Energy Optimization in Commercial FPGAs with Voltage, Frequency and Logic Scaling

This paper investigates the energy reductions possible in commercially available FPGAs configured to support voltage, frequency and logic scalability combined with power gating. Voltage and frequency scaling is based on in-situ detectors that allow the device to detect valid working voltage and frequency pairs at run-time while logic scalability is achieved with partial dynamic reconfiguration. The considered devices are FPGA-processor hybrids with independent power domains fabricated in 28 nm process nodes. The test case is based on a number of operational scenarios in which the FPGA side is loaded with a motion estimation core that can be configured with a variable number of execution units. The results demonstrate that voltage scalability reduces power by up to 60 percent compared with nominal voltage operation at the same frequency. The energy analysis show that the most energy efficiency core configuration depends on the performance requirements. A low performance scenario shows that serial computation is more energy efficient than the parallel configuration while the opposite is true when the performance requirements increase. An algorithm is proposed to combine effectively adaptive voltage/logic scaling and power gating in the proposed system and application

Evaluating Built-in ECC of FPGA on-chip Memories for the Mitigation of Undervolting Faults

Voltage underscaling below the nominal level is an effective solution for improving energy efficiency in digital circuits, e.g., Field Programmable Gate Arrays (FPGAs). However, further undervolting below a safe voltage level and without accompanying frequency scaling leads to timing related faults, potentially undermining the energy savings. Through experimental voltage underscaling studies on commercial FPGAs, we observed that the rate of these faults exponentially increases for on-chip memories, or Block RAMs (BRAMs). To mitigate these faults, we evaluated the efficiency of the built-in Error-Correction Code (ECC) and observed that more than 90% of the faults are correctable and further 7% are detectable (but not correctable). This efficiency is the result of the single-bit type of these faults, which are then effectively covered by the Single-Error Correction and Double-Error Detection (SECDED) design of the built-in ECC. Finally, motivated by the above experimental observations, we evaluated an FPGA-based Neural Network (NN) accelerator under low-voltage operations, while built-in ECC is leveraged to mitigate undervolting faults and thus, prevent NN significant accuracy loss. In consequence, we achieve 40% of the BRAM power saving through undervolting below the minimum safe voltage level, with a negligible NN accuracy loss, thanks to the substantial fault coverage by the built-in ECC.Comment: 6 pages, 2 figure

FPGA Energy Efficiency by Leveraging Thermal Margin

Cutting edge FPGAs are not energy efficient as conventionally presumed to be, and therefore, aggressive power-saving techniques have become imperative. The clock rate of an FPGA-mapped design is set based on worst-case conditions to ensure reliable operation under all circumstances. This usually leaves a considerable timing margin that can be exploited to reduce power consumption by scaling voltage without lowering clock frequency. There are hurdles for such opportunistic voltage scaling in FPGAs because (a) critical paths change with designs, making timing evaluation difficult as voltage changes, (b) each FPGA resource has particular power-delay trade-off with voltage, (c) data corruption of configuration cells and memory blocks further hampers voltage scaling. In this paper, we propose a systematical approach to leverage the available thermal headroom of FPGA-mapped designs for power and energy improvement. By comprehensively analyzing the timing and power consumption of FPGA building blocks under varying temperatures and voltages, we propose a thermal-aware voltage scaling flow that effectively utilizes the thermal margin to reduce power consumption without degrading performance. We show the proposed flow can be employed for energy optimization as well, whereby power consumption and delay are compromised to accomplish the tasks with minimum energy. Lastly, we propose a simulation framework to be able to examine the efficiency of the proposed method for other applications that are inherently tolerant to a certain amount of error, granting further power saving opportunity. Experimental results over a set of industrial benchmarks indicate up to 36% power reduction with the same performance, and 66% total energy saving when energy is the optimization target.Comment: Accepted in IEEE International Conference on Computer Design (ICCD) 201

Optimizing energy efficiency of CNN-based object detection with dynamic voltage and frequency scaling

On the one hand, accelerating convolution neural networks (CNNs) on FPGAs requires ever increasing high energy efficiency in the edge computing paradigm. On the other hand, unlike normal digital algorithms, CNNs maintain their high robustness even with limited timing errors. By taking advantage of this unique feature, we propose to use dynamic voltage and frequency scaling (DVFS) to further optimize the energy efficiency for CNNs. First, we have developed a DVFS framework on FPGAs. Second, we apply the DVFS to SkyNet, a state-of-the-art neural network targeting on object detection. Third, we analyze the impact of DVFS on CNNs in terms of performance, power, energy efficiency and accuracy. Compared to the state-of-the-art, experimental results show that we have achieved 38% improvement in energy efficiency without any loss in accuracy. Results also show that we can achieve 47% improvement in energy efficiency if we allow 0.11% relaxation in accuracy