12 research outputs found

    Noncooperative and Cooperative Transmission Schemes with Precoding and Beamforming

    Get PDF
    The next generation mobile networks are expected to provide multimedia applications with a high quality of service. On the other hand, interference among multiple base stations (BS) that co-exist in the same location limits the capacity of wireless networks. In conventional wireless networks, the base stations do not cooperate with each other. The BSs transmit individually to their respective mobile stations (MS) and treat the transmission from other BSs as interference. An alternative to this structure is a network cooperation structure. Here, BSs cooperate with other BSs to simultaneously transmit to their respective MSs using the same frequency band at a given time slot. By doing this, we significantly increase the capacity of the networks. This thesis presents novel research results on a noncooperative transmission scheme and a cooperative transmission scheme for multi-user multiple-input-multiple-output orthogonal frequency division multiplexing (MIMO-OFDM). We first consider the performance limit of a noncooperative transmission scheme. Here, we propose a method to reduce the interference and increase the throughput of orthogonal frequency division multiplexing (OFDM) systems in co-working wireless local area networks (WLANs) by using joint adaptive multiple antennas(AMA) and adaptive modulation (AM) with acknowledgement (ACK) Eigen-steering. The calculation of AMA and AM are performed at the receiver. The AMA is used to suppress interference and to maximize the signal-to-interference-plus-noise ratio (SINR). The AM scheme is used to allocate OFDM sub-carriers, power, and modulation mode subject to the constraints of power, discrete modulation, and the bit error rate (BER). The transmit weights, the allocation of power, and the allocation of sub-carriers are obtained at the transmitter using ACK Eigen-steering. The derivations of AMA, AM, and ACK Eigen-steering are shown. The performance of joint AMA and AM for various AMA configurations is evaluated through the simulations of BER and spectral efficiency (SE) against SIR. To improve the performance of the system further, we propose a practical cooperative transmission scheme to mitigate against the interference in co-working WLANs. Here, we consider a network coordination among BSs. We employ Tomlinson Harashima precoding (THP), joint transmit-receive beamforming based on SINR (signal-to-interference-plus-noise-ratio) maximization, and an adaptive precoding order to eliminate co-working interference and achieve bit error rate (BER) fairness among different users. We also consider the design of the system when partial channel state information (CSI) (where each user only knows its own CSI) and full CSI (where each user knows CSI of all users) are available at the receiver respectively. We prove analytically and by simulation that the performance of our proposed scheme will not be degraded under partial CSI. The simulation results show that the proposed scheme considerably outperforms both the existing noncooperative and cooperative transmission schemes. A method to design a spectrally efficient cooperative downlink transmission scheme employing precoding and beamforming is also proposed. The algorithm eliminates the interference and achieves symbol error rate (SER) fairness among different users. To eliminate the interference, Tomlinson Harashima precoding (THP) is used to cancel part of the interference while the transmit-receive antenna weights cancel the remaining one. A new novel iterative method is applied to generate the transmit-receive antenna weights. To achieve SER fairness among different users and further improve the performance of MIMO systems, we develop algorithms that provide equal SINR across all users and order the users so that the minimum SINR for each user is maximized. The simulation results show that the proposed scheme considerably outperforms existing cooperative transmission schemes in terms of the SER performance and complexity and approaches an interference free performance under the same configuration. We could improve the performance of the proposed interference cancellation further. This is because the proposed interference cancellation does not consider receiver noise when calculating the transmit-receive weight antennas. In addition, the proposed scheme mentioned above is designed specifically for a single-stream multi-user transmission. Here, we employ THP precoding and an iterative method based on the uplink-downlink duality principle to generate the transmit-receive antenna weights. The algorithm provides an equal SINR across all users. A simpler method is then proposed by trading off the complexity with a slight performance degradation. The proposed methods are extended to also work when the receiver does not have complete Channel State Informations (CSIs). A new method of setting the user precoding order, which has a much lower complexity than the VBLAST type ordering scheme but with almost the same performance, is also proposed. The simulation results show that the proposed schemes considerably outperform existing cooperative transmission schemes in terms of SER performance and approach an interference free performance. In all the cooperative transmission schemes proposed above, we use THP to cancel part of the interference. In this thesis, we also consider an alternative approach that bypasses the use of THP. The task of cancelling the interference from other users now lies solely within the transmit-receive antenna weights. We consider multiuser Gaussian broadcast channels with multiple antennas at both transmitter and receivers. An iterative multiple beamforming (IMB) algorithm is proposed, which is flexible in the antenna configuration and performs well in low to moderate data rates. Its capacity and bit error rate performance are compared with the ones achieved by the traditional zero-forcing method

    Noncooperative and Cooperative Transmission Schemes with Precoding and Beamforming

    Get PDF
    The next generation mobile networks are expected to provide multimedia applications with a high quality of service. On the other hand, interference among multiple base stations (BS) that co-exist in the same location limits the capacity of wireless networks. In conventional wireless networks, the base stations do not cooperate with each other. The BSs transmit individually to their respective mobile stations (MS) and treat the transmission from other BSs as interference. An alternative to this structure is a network cooperation structure. Here, BSs cooperate with other BSs to simultaneously transmit to their respective MSs using the same frequency band at a given time slot. By doing this, we significantly increase the capacity of the networks. This thesis presents novel research results on a noncooperative transmission scheme and a cooperative transmission scheme for multi-user multiple-input-multiple-output orthogonal frequency division multiplexing (MIMO-OFDM). We first consider the performance limit of a noncooperative transmission scheme. Here, we propose a method to reduce the interference and increase the throughput of orthogonal frequency division multiplexing (OFDM) systems in co-working wireless local area networks (WLANs) by using joint adaptive multiple antennas(AMA) and adaptive modulation (AM) with acknowledgement (ACK) Eigen-steering. The calculation of AMA and AM are performed at the receiver. The AMA is used to suppress interference and to maximize the signal-to-interference-plus-noise ratio (SINR). The AM scheme is used to allocate OFDM sub-carriers, power, and modulation mode subject to the constraints of power, discrete modulation, and the bit error rate (BER). The transmit weights, the allocation of power, and the allocation of sub-carriers are obtained at the transmitter using ACK Eigen-steering. The derivations of AMA, AM, and ACK Eigen-steering are shown. The performance of joint AMA and AM for various AMA configurations is evaluated through the simulations of BER and spectral efficiency (SE) against SIR. To improve the performance of the system further, we propose a practical cooperative transmission scheme to mitigate against the interference in co-working WLANs. Here, we consider a network coordination among BSs. We employ Tomlinson Harashima precoding (THP), joint transmit-receive beamforming based on SINR (signal-to-interference-plus-noise-ratio) maximization, and an adaptive precoding order to eliminate co-working interference and achieve bit error rate (BER) fairness among different users. We also consider the design of the system when partial channel state information (CSI) (where each user only knows its own CSI) and full CSI (where each user knows CSI of all users) are available at the receiver respectively. We prove analytically and by simulation that the performance of our proposed scheme will not be degraded under partial CSI. The simulation results show that the proposed scheme considerably outperforms both the existing noncooperative and cooperative transmission schemes. A method to design a spectrally efficient cooperative downlink transmission scheme employing precoding and beamforming is also proposed. The algorithm eliminates the interference and achieves symbol error rate (SER) fairness among different users. To eliminate the interference, Tomlinson Harashima precoding (THP) is used to cancel part of the interference while the transmit-receive antenna weights cancel the remaining one. A new novel iterative method is applied to generate the transmit-receive antenna weights. To achieve SER fairness among different users and further improve the performance of MIMO systems, we develop algorithms that provide equal SINR across all users and order the users so that the minimum SINR for each user is maximized. The simulation results show that the proposed scheme considerably outperforms existing cooperative transmission schemes in terms of the SER performance and complexity and approaches an interference free performance under the same configuration. We could improve the performance of the proposed interference cancellation further. This is because the proposed interference cancellation does not consider receiver noise when calculating the transmit-receive weight antennas. In addition, the proposed scheme mentioned above is designed specifically for a single-stream multi-user transmission. Here, we employ THP precoding and an iterative method based on the uplink-downlink duality principle to generate the transmit-receive antenna weights. The algorithm provides an equal SINR across all users. A simpler method is then proposed by trading off the complexity with a slight performance degradation. The proposed methods are extended to also work when the receiver does not have complete Channel State Informations (CSIs). A new method of setting the user precoding order, which has a much lower complexity than the VBLAST type ordering scheme but with almost the same performance, is also proposed. The simulation results show that the proposed schemes considerably outperform existing cooperative transmission schemes in terms of SER performance and approach an interference free performance. In all the cooperative transmission schemes proposed above, we use THP to cancel part of the interference. In this thesis, we also consider an alternative approach that bypasses the use of THP. The task of cancelling the interference from other users now lies solely within the transmit-receive antenna weights. We consider multiuser Gaussian broadcast channels with multiple antennas at both transmitter and receivers. An iterative multiple beamforming (IMB) algorithm is proposed, which is flexible in the antenna configuration and performs well in low to moderate data rates. Its capacity and bit error rate performance are compared with the ones achieved by the traditional zero-forcing method

    Protocols for multi-antenna ad-hoc wireless networking in interference environments

    Get PDF
    Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2010.Cataloged from PDF version of thesis.Includes bibliographical references (p. 231-242).A fundamental question for the design of future wireless networks concerns the nature of spectrum management and the protocols that govern use of the spectrum. In the oligopoly model, spectrum is owned and centrally managed, and the protocols tend to reflect this centralized nature. In the common's model, spectrum is a public good, and protocols must support ad hoc communication. This work presents the design, tradeoffs and parameter optimization for a new protocol (Simultaneous Transmissions in Interference (STI-MAC)) for ad hoc wireless networks. The key idea behind the STI-MAC protocol is 'channel stuffing,' that is, allowing network nodes to more efficiently use spatial, time and frequency degrees of freedom. This is achieved in three key ways. First, 'channel stuffing' is achieved through multiple antennas that are used at the receiver to mitigate interference using Minimum-Mean-Squared-Error (MMSE) receivers, allowing network nodes to transmit simultaneously in interference limited environments. The protocol also supports the use of multiple transmit antennas to beamform to the target receiver. Secondly, 'channel stuffing' is achieved through the use of a control channel that is orthogonal in time to the data channel, where nodes contend in order to participate on the data channel. And thirdly, 'channel stuffing' is achieved through a protest scheme that prevents data channel overloading. The STI-MAC protocol is analyzed via Monte-Carlo simulations in which transmitter nodes are uniformly distributed in a plane, each at a fixed distance from their target receiver; and as a function of network parameters including the number of transmit and receive antennas, the distance between a transmitter-receiver pair (link-length), the average number of transmitters whose received signal is stronger at a given receiver than its target transmitter (link-rank), number of transmitter-receiver pairs, the distribution on the requested rate, the offered load, and the transmit scheme. The STI-MAC protocol is benchmarked relative to simulations of the 802.11(n) (Wi-Fi) protocol. The key results of this work show a 3X gain in throughput relative to 802.11(n) in typical multi-antenna wireless networks that have 20 transmitter-receiver pairs, a link-length of 10 meters, four receive antennas and a single transmit antenna. We also show a reduction in delay by a factor of two when the networks are heavily loaded. We find that the link-rank is a key parameter affecting STIMAC gains over Wi-Fi. In simulations of networks with 40 transmit-receiver pairs, link-rank of three, a link-length of 10 meters, and eight transmit and receive antennas in which the transmitter beamforms to its target receiver in its strongest target channel mode, we find gains in throughput of at least 5X over the 802.11(n) protocol.by Danielle A. Hinton.Ph.D

    Channelization, Link Adaptation and Multi-antenna Techniques for OFDM(A) Based Wireless Systems

    Get PDF

    Adaptation of the IEEE 802.11 protocol for inter-satellite links in LEO satellite networks

    Get PDF
    Knowledge of the coefficient of thermal expansion (CTE) of a ceramic material is important in many application areas. Whilst the CTE can be measured, it would be useful to be able to predict the expansion behaviour of multiphase materials.. There are several models for the CTE, however, most require a knowledge of the elastic properties of the constituent phases and do not take account ofthe microstructural features of the material. If the CTE could be predicted on the basis of microstructural information, this would then lead to the ability to engineer the microstructure of multiphase ceramic materials to produce acceptable thermal expansion behaviour. To investigate this possibility, magnesia-magnesium aluminate sp~el (MMAS) composites, consisting of a magnesia matrix and magnesium aluminate s~ne'l (MAS) particles, were studied. Having determined a procedure to produce MAS fr alumina and magnesia, via solid state sintering, magnesia-rich compositions wit ~ various magnesia contents were prepared to make the MMAS composites. Further, the l\.1MAS composites prepared from different powders (i.e. from an alumina-magnesia mixture ahd from a magnesia-spinel powder) were compared. Com starch was added into the powder mixtures before sintering to make porous microstructures. Microstructural development and thermal expansion behaviour ofthe MMAS composites were investigated. Microstructures of the MAS and the MMAS composites as well as their porous bodies were quaritified from backscattered electron micrographs in terms of the connectivity of solids i.e. solid contiguity by means of linear intercept counting. Solid contiguity decreased with increasing pore content and varied with pore size, pore shape and pore distribution whereas the phase contiguity depended strongly on the chemical composition and was less influenced by porosity. ' The thermal expansion behaviour of the MAS and the MMAS composites between 100 and 1000 °C was determined experimentally. Variation in the CTE ofthe MAS relates to the degree of spinel formation while the thermal expansion of the MMAS composites depends strongly on phase content. However, the MMAS composites with similar phase compositions but made from different manufacturing processes showed differences in microstructural features and thermal expansion behaviour. Predictions of the CTE values for composites based on a simple rule-of-mixtures (ROM) using volume fraction were compared with the measured data. A conventional ROM accurately predicted the effective CTE of a range of dense alumina-silicon carbide particulate composites but was not very accurate for porous multiphase structures. It provided an upper bound prediction as all experimental values were lower. Hence, the conventional ROM was modified to take account of quantitative microstructural parameters obtained from solid contiguity. The modified ROM predicted lower values and gave a good agreement with the experimental data. Thus, it has been shown that quantitative microstructural information can be used to predict the CTE of multiphase ceramic materials with complex microstructures.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

    Recent Advances in Wireless Communications and Networks

    Get PDF
    This book focuses on the current hottest issues from the lowest layers to the upper layers of wireless communication networks and provides "real-time" research progress on these issues. The authors have made every effort to systematically organize the information on these topics to make it easily accessible to readers of any level. This book also maintains the balance between current research results and their theoretical support. In this book, a variety of novel techniques in wireless communications and networks are investigated. The authors attempt to present these topics in detail. Insightful and reader-friendly descriptions are presented to nourish readers of any level, from practicing and knowledgeable communication engineers to beginning or professional researchers. All interested readers can easily find noteworthy materials in much greater detail than in previous publications and in the references cited in these chapters

    Layer 2 Path Selection Protocol for Wireless Mesh Networks with Smart Antennas

    Get PDF
    In this thesis the possibilities of smart antenna systems in wireless mesh networks are examined. With respect to the individual smart antenna tradeoffs, a routing protocol (Modified HWMP, MHWMP) for IEEE 802.11s mesh networks is presented, that exploits the full range of benefits provided by smart antennas: MHWMP actively switches between the PHY-layer transmission/reception modes (multiplexing, beamforming and diversity) according to the wireless channel conditions. Spatial multiplexing and beamforming are used for unicast data transmissions, while antenna diversity is employed for efficient broadcasts. To adapt to the directional channel environment and to take full benefit of the PHY capabilities, a respective MAC scheme is employed. The presented protocol is tested in extensive simulation and the results are examined.:1 Introduction 2 Wireless Mesh Networks 3 IEEE 802.11s 4 Smart Antenna Concepts 5 State of the Art: Wireless Mesh Networks with Smart Antennas 6 New Concepts 7 System Model 8 Results and Discussion 9 Conclusion and Future Wor

    Cooperative Radio Communications for Green Smart Environments

    Get PDF
    The demand for mobile connectivity is continuously increasing, and by 2020 Mobile and Wireless Communications will serve not only very dense populations of mobile phones and nomadic computers, but also the expected multiplicity of devices and sensors located in machines, vehicles, health systems and city infrastructures. Future Mobile Networks are then faced with many new scenarios and use cases, which will load the networks with different data traffic patterns, in new or shared spectrum bands, creating new specific requirements. This book addresses both the techniques to model, analyse and optimise the radio links and transmission systems in such scenarios, together with the most advanced radio access, resource management and mobile networking technologies. This text summarises the work performed by more than 500 researchers from more than 120 institutions in Europe, America and Asia, from both academia and industries, within the framework of the COST IC1004 Action on "Cooperative Radio Communications for Green and Smart Environments". The book will have appeal to graduates and researchers in the Radio Communications area, and also to engineers working in the Wireless industry. Topics discussed in this book include: • Radio waves propagation phenomena in diverse urban, indoor, vehicular and body environments• Measurements, characterization, and modelling of radio channels beyond 4G networks• Key issues in Vehicle (V2X) communication• Wireless Body Area Networks, including specific Radio Channel Models for WBANs• Energy efficiency and resource management enhancements in Radio Access Networks• Definitions and models for the virtualised and cloud RAN architectures• Advances on feasible indoor localization and tracking techniques• Recent findings and innovations in antenna systems for communications• Physical Layer Network Coding for next generation wireless systems• Methods and techniques for MIMO Over the Air (OTA) testin

    Cooperative Radio Communications for Green Smart Environments

    Get PDF
    The demand for mobile connectivity is continuously increasing, and by 2020 Mobile and Wireless Communications will serve not only very dense populations of mobile phones and nomadic computers, but also the expected multiplicity of devices and sensors located in machines, vehicles, health systems and city infrastructures. Future Mobile Networks are then faced with many new scenarios and use cases, which will load the networks with different data traffic patterns, in new or shared spectrum bands, creating new specific requirements. This book addresses both the techniques to model, analyse and optimise the radio links and transmission systems in such scenarios, together with the most advanced radio access, resource management and mobile networking technologies. This text summarises the work performed by more than 500 researchers from more than 120 institutions in Europe, America and Asia, from both academia and industries, within the framework of the COST IC1004 Action on "Cooperative Radio Communications for Green and Smart Environments". The book will have appeal to graduates and researchers in the Radio Communications area, and also to engineers working in the Wireless industry. Topics discussed in this book include: • Radio waves propagation phenomena in diverse urban, indoor, vehicular and body environments• Measurements, characterization, and modelling of radio channels beyond 4G networks• Key issues in Vehicle (V2X) communication• Wireless Body Area Networks, including specific Radio Channel Models for WBANs• Energy efficiency and resource management enhancements in Radio Access Networks• Definitions and models for the virtualised and cloud RAN architectures• Advances on feasible indoor localization and tracking techniques• Recent findings and innovations in antenna systems for communications• Physical Layer Network Coding for next generation wireless systems• Methods and techniques for MIMO Over the Air (OTA) testin
    corecore