Direct Digital Frequency Synthesizer Architecture for Wireless Communication in 90 NM CMOS Technology

Software radio is one promising field that can meet the demands for low cost, low power, and high speed electronic devices for wireless communication. At the heart of software radio is a programmable oscillator called a Direct Digital Synthesizer (DDS). DDS has the capabilities of rapid frequency hopping by digital software control while operating at very high frequencies and having sub-hertz resolution. Nevertheless, the digital-to-analog converter (DAC) and the read-only-memory (ROM) look-up table, building blocks of the DDS, prevent the DDS to be used in wireless communication because they introduce errors and noises to the DDS and their performances deteriorate at high speed. The DAC and ROM are replaced in this thesis by analog active filters that convert the square wave output of the phase accumulator directly into a sine wave. The proposed architecture operates with a reference clock of 9.09 GHz and can be fully-integrated in 90 nm CMOS technology

Techniques for high-performance digital frequency synthesis and phase control

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2008.Includes bibliographical references (p. 183-190).This thesis presents a 3.6-GHz, 500-kHz bandwidth digital [delta][sigma] frequency synthesizer architecture that leverages a recently invented noise-shaping time-to-digital converter (TDC) and an all-digital quantization noise cancellation technique to achieve excellent in-band and out-of-band phase noise, respectively. In addition, a passive digital-to-analog converter (DAC) structure is proposed as an efficient interface between the digital loop filter and a conventional hybrid voltage-controlled oscillator (VCO) to create a digitally-controlled oscillator (DCO). An asynchronous divider structure is presented which lowers the required TDC range and avoids the divide-value-dependent delay variation. The prototype is implemented in a 0.13-am CMOS process and its active area occupies 0.95 mm². Operating under 1.5 V, the core parts, excluding the VCO output buffer, dissipate 26 mA. Measured phase noise at 3.67 GHz achieves -108 dBc/Hz and -150 dBc/Hz at 400 kHz and 20 MHz, respectively. Integrated phase noise at this carrier frequency yields 204 fs of jitter (measured from 1 kHz to 40 MHz). In addition, a 3.2-Gb/s delay-locked loop (DLL) in a 0.18-[mu]m CMOS for chip-tochip communications is presented. By leveraging the fractional-N synthesizer technique, this architecture provides a digitally-controlled delay adjustment with a fine resolution and infinite range. The provided delay resolution is less sensitive to the process, voltage, and temperature variations than conventional techniques. A new [delta][sigma] modulator enables a compact and low-power implementation of this architecture. A simple bang-bang detector is used for phase detection. The prototype operates at a 1.8-V supply voltage with a current consumption of 55 mA. The phase resolution and differential rms clock jitter are 1.4 degrees and 3.6 ps, respectively.by Chun-Ming Hsu.Ph.D

Spur Reduction Techniques for Phase-Locked Loops Exploiting A Sub-Sampling Phase Detector

This paper presents phase-locked loop (PLL) reference-spur reduction design techniques exploiting a sub-sampling phase detector (SSPD) (which is also referred to as a sampling phase detector). The VCO is sampled by the reference clock without using a frequency divider and an amplitude controlled charge pump is used which is inherently insensitive to mismatch. The main remaining source of the VCO reference spur is the periodic disturbance of the VCO by the sampling at the reference frequency. The underlying VCO sampling spur mechanisms are analyzed and their effect is minimized by using dummy samplers and isolation buffers. A duty-cycle-controlled reference buffer and delay-locked loop (DLL) tuning are proposed to further reduce the worst case spur level. To demonstrate the effectiveness of the\ud proposed spur reduction techniques, a 2.21 GHz PLL is designed and fabricated in 0.18 m CMOS technology. While using a high loop-bandwidth-to-reference-frequency ratio of 1/20, the reference spur measured from 20 chips is 80 dBc. The PLL consumes 3.8 mW while the in-band phase noise is 121 dBc/Hz at 200 kHz and the output jitter integrated from 10 kHz to 100 MHz is 0.3 ps rms

A Low Noise Sub-Sampling PLL in Which Divider Noise Is Eliminated and PD-CP Noise Is not multiplied by N^2

This paper presents a 2.2-GHz low jitter sub-sampling based PLL. It uses a phase-detector/charge-pump (PD/CP)that sub-samples the VCO output with the reference clock. In contrast to what happens in a classical PLL, the PD/CP noise is not multiplied by N2 in this sub-sampling PLL, resulting in a low noise contribution from the PD/CP. Moreover, no frequency divider is needed in the locked state and hence divider noise and power can be eliminated. An added frequency locked loop guarantees correct frequency locking without degenerating jitter performance when in lock. The PLL is implemented in a standard 0.18- m CMOS process. It consumes 4.2 mA from a 1.8 V supply and occupies an active area of 0.4 X 0.45 m

High Performance Local Oscillator Design for Next Generation Wireless Communication

Local Oscillator (LO) is an essential building block in modern wireless radios. In modern wireless radios, LO often serves as a reference of the carrier signal to modulate or demod- ulate the outgoing or incoming data. The LO signal should be a clean and stable source, such that the frequency or timing information of the carrier reference can be well-defined. However, as radio architecture evolves, the importance of LO path design has become much more important than before. Of late, many radio architecture innovations have exploited sophisticated LO generation schemes to meet the ever-increasing demands of wireless radio performances. The focus of this thesis is to address challenges in the LO path design for next-generation high performance wireless radios. These challenges include (1) Congested spectrum at low radio frequency (RF) below 5GHz (2) Continuing miniaturization of integrated wireless radio, and (3) Fiber-fast (>10Gb/s) mm-wave wireless communication. The thesis begins with a brief introduction of the aforementioned challenges followed by a discussion of the opportunities projected to overcome these challenges. To address the challenge of congested spectrum at frequency below 5GHz, novel ra- dio architectures such as cognitive radio, software-defined radio, and full-duplex radio have drawn significant research interest. Cognitive radio is a radio architecture that opportunisti- cally utilize the unused spectrum in an environment to maximize spectrum usage efficiency. Energy-efficient spectrum sensing is the key to implementing cognitive radio. To enable energy-efficient spectrum sensing, a fast-hopping frequency synthesizer is an essential build- ing block to swiftly sweep the carrier frequency of the radio across the available spectrum. Chapter 2 of this thesis further highlights the challenges and trade-offs of the current LO gen- eration scheme for possible use in sweeping LO-based spectrum analysis. It follows by intro- duction of the proposed fast-hopping LO architecture, its implementation and measurement results of the validated prototype. Chapter 3 proposes an embedded phase-shifting LO-path design for wideband RF self-interference cancellation for full-duplex radio. It demonstrates a synergistic design between the LO path and signal to perform self-interference cancellation. To address the challenge of continuing miniaturization of integrated wireless radio, ring oscillator-based frequency synthesizer is an attractive candidate due to its compactness. Chapter 4 discussed the difficulty associated with implementing a Phase-Locked Loop (PLL) with ultra-small form-factor. It further proposes the concept sub-sampling PLL with time- based loop filter to address these challenges. A 65nm CMOS prototype and its measurement result are presented for validation of the concept. In shifting from RF to mm-wave frequencies, the performance of wireless communication links is boosted by significant bandwidth and data-rate expansion. However, the demand for data-rate improvement is out-pacing the innovation of radio architectures. A >10Gb/s mm-wave wireless communication at 60GHz is required by emerging applications such as virtual-reality (VR) headsets, inter-rack data transmission at data center, and Ultra-High- Definition (UHD) TV home entertainment systems. Channel-bonding is considered to be a promising technique for achieving >10Gb/s wireless communication at 60GHz. Chapter 5 discusses the fundamental radio implementation challenges associated with channel-bonding for 60GHz wireless communication and the pros and cons of prior arts that attempted to address these challenges. It is followed by a discussion of the proposed 60GHz channel- bonding receiver, which utilizes only a single PLL and enables both contiguous and non- contiguous channel-bonding schemes. Finally, Chapter 6 presents the conclusion of this thesis

Delay Flip-Flop (DFF) Metastability Impact on Clock and Data Recovery (CDR) and Phase-Locked Loop (PLL) Circuits

Modeling delay flip-flops for binary (e.g., Alexander) phase detectors requires paying close attention to three important timing parameters: setup time, hold time, and clock edge-to-output (or briefly C2Q time). These parameters have a critical role in determining the status of the system on the circuit level. This study provided a guideline for designing an optimum DFF for an Alexander phase detector in a clock and data recovery circuit. Furthermore, it indicated DFF timing requirements for a high-speed phase detector in a clock and data recovery circuit. The CDR was also modeled by Verilog-A, and the results were compared with Simulink model achievements. Eventually designed in 45 nm CMOS technology, for 10 Gbps random sequence, the recovered clock contained 0.136 UI and 0.15 UI peak-to-peak jitter on the falling and rising edges respectively, and the lock time was 125 ns. The overall power dissipation was 21 mW from a 1 V supply voltage. Future work includes layout design and manufacturing of the proposed design

Process and Temperature Compensated Wideband Injection Locked Frequency Dividers and their Application to Low-Power 2.4-GHz Frequency Synthesizers

There has been a dramatic increase in wireless awareness among the user community in the past five years. The 2.4-GHz Industrial, Scientific and Medical (ISM) band is being used for a diverse range of applications due to the following reasons. It is the only unlicensed band approved worldwide and it offers more bandwidth and supports higher data rates compared to the 915-MHz ISM band. The power consumption of devices utilizing the 2.4-GHz band is much lower compared to the 5.2-GHz ISM band. Protocols like Bluetooth and Zigbee that utilize the 2.4-GHz ISM band are becoming extremely popular. Bluetooth is an economic wireless solution for short range connectivity between PC, cell phones, PDAs, Laptops etc. The Zigbee protocol is a wireless technology that was developed as an open global standard to address the unique needs of low-cost, lowpower, wireless sensor networks. Wireless sensor networks are becoming ubiquitous, especially after the recent terrorist activities. Sensors are employed in strategic locations for real-time environmental monitoring, where they collect and transmit data frequently to a nearby terminal. The devices operating in this band are usually compact and battery powered. To enhance battery life and avoid the cumbersome task of battery replacement, the devices used should consume extremely low power. Also, to meet the growing demands cost and sized has to be kept low which mandates fully monolithic implementation using low cost process. CMOS process is extremely attractive for such applications because of its low cost and the possibility to integrate baseband and high frequency circuits on the same chip. A fully integrated solution is attractive for low power consumption as it avoids the need for power hungry drivers for driving off-chip components. The transceiver is often the most power hungry block in a wireless communication system. The frequency divider (prescaler) and the voltage controlled oscillator in the transmitter’s frequency synthesizer are among the major sources of power consumption. There have been a number of publications in the past few decades on low-power high-performance VCOs. Therefore this work focuses on prescalers. A class of analog frequency dividers called as Injection-Locked Frequency Dividers (ILFD) was introduced in the recent past as low power frequency division. ILFDs can consume an order of magnitude lower power when compared to conventional flip-flop based dividers. However the range of operation frequency also knows as the locking range is limited. ILFDs can be classified as LC based and Ring based. Though LC based are insensitive to process and temperature variation, they cannot be used for the 2.4-GHz ISM band because of the large size of on-chip inductors at these frequencies. This causes a lot of valuable chip area to be wasted. Ring based ILFDs are compact and provide a low power solution but are extremely sensitive to process and temperature variations. Process and temperature variation can cause ring based ILFD to loose lock in the desired operating band. The goal of this work is to make the ring based ILFDs useful for practical applications. Techniques to extend the locking range of the ILFDs are discussed. A novel and simple compensation technique is devised to compensate the ILFD and keep the locking range tight with process and temperature variations. The proposed ILFD is used in a 2.4-GHz frequency synthesizer that is optimized for fractional-N synthesis. Measurement results supporting the theory are provided

고속 시리얼 링크를 위한 고리 발진기를 기반으로 하는 주파수 합성기

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this dissertation, major concerns in the clocking of modern serial links are discussed. As sub-rate, multi-standard architectures are becoming predominant, the conventional clocking methodology seems to necessitate innovation in terms of low-cost implementation. Frequency synthesis with active, inductor-less oscillators replacing LC counterparts are reviewed, and solutions for two major drawbacks are proposed. Each solution is verified by prototype chip design, giving a possibility that the inductor-less oscillator may become a proper candidate for future high-speed serial links. To mitigate the high flicker noise of a high-frequency ring oscillator (RO), a reference multiplication technique that effectively extends the bandwidth of the following all-digital phase-locked loop (ADPLL) is proposed. The technique avoids any jitter accumulation, generating a clean mid-frequency clock, overall achieving high jitter performance in conjunction with the ADPLL. Timing constraint for the proper reference multiplication is first analyzed to determine the calibration points that may correct the existent phase errors. The weight for each calibration point is updated by the proposed a priori probability-based least-mean-square (LMS) algorithm. To minimize the time required for the calibration, each gain for the weight update is adaptively varied by deducing a posteriori which error source dominates the others. The prototype chip is fabricated in a 40-nm CMOS technology, and its measurement results verify the low-jitter, high-frequency clock generation with fast calibration settling. The presented work achieves an rms jitter of 177/223 fs at 8/16-GHz output, consuming 12.1/17-mW power. As the second embodiment, an RO-based ADPLL with an analog technique that addresses the high supply sensitivity of the RO is presented. Unlike prior arts, the circuit for the proposed technique does not extort the RO voltage headroom, allowing high-frequency oscillation. Further, the performance given from the technique is robust over process, voltage, and temperature (PVT) variations, avoiding the use of additional calibration hardware. Lastly, a comprehensive analysis of phase noise contribution is conducted for the overall ADPLL, followed by circuit optimizations, to retain the low-jitter output. Implemented in a 40-nm CMOS technology, the frequency synthesizer achieves an rms jitter of 289 fs at 8 GHz output without any injected supply noise. Under a 20-mVrms white supply noise, the ADPLL suppresses supply-noise-induced jitter by -23.8 dB.본 논문은 현대 시리얼 링크의 클락킹에 관여되는 주요한 문제들에 대하여 기술한다. 준속도, 다중 표준 구조들이 채택되고 있는 추세에 따라, 기존의 클라킹 방법은 낮은 비용의 구현의 관점에서 새로운 혁신을 필요로 한다. LC 공진기를 대신하여 능동 소자 발진기를 사용한 주파수 합성에 대하여 알아보고, 이에 발생하는 두가지 주요 문제점과 각각에 대한 해결 방안을 탐색한다. 각 제안 방법을 프로토타입 칩을 통해 그 효용성을 검증하고, 이어서 능동 소자 발진기가 미래의 고속 시리얼 링크의 클락킹에 사용될 가능성에 대해 검토한다. 첫번째 시연으로써, 고주파 고리 발진기의 높은 플리커 잡음을 완화시키기 위해 기준 신호를 배수화하여 뒷단의 위상 고정 루프의 대역폭을 효과적으로 극대화 시키는 회로 기술을 제안한다. 본 기술은 지터를 누적 시키지 않으며 따라서 깨끗한 중간 주파수 클락을 생성시켜 위상 고정 루프와 함께 높은 성능의 고주파 클락을 합성한다. 기준 신호를 성공적으로 배수화하기 위한 타이밍 조건들을 먼저 분석하여 타이밍 오류를 제거하기 위한 방법론을 파악한다. 각 교정 중량은 연역적 확률을 기반으로한 LMS 알고리즘을 통해 갱신되도록 설계된다. 교정에 필요한 시간을 최소화 하기 위하여, 각 교정 이득은 타이밍 오류 근원들의 크기를 귀납적으로 추론한 값을 바탕으로 지속적으로 제어된다. 40-nm CMOS 공정으로 구현된 프로토타입 칩의 측정을 통해 저소음, 고주파 클락을 빠른 교정 시간안에 합성해 냄을 확인하였다. 이는 177/223 fs의 rms 지터를 가지는 8/16 GHz의 클락을 출력한다. 두번째 시연으로써, 고리 발진기의 높은 전원 노이즈 의존성을 완화시키는 기술이 포함된 주파수 합성기가 설계되었다. 이는 고리 발진기의 전압 헤드룸을 보존함으로서 고주파 발진을 가능하게 한다. 나아가, 전원 노이즈 감소 성능은 공정, 전압, 온도 변동에 대하여 민감하지 않으며, 따라서 추가적인 교정 회로를 필요로 하지 않는다. 마지막으로, 위상 노이즈에 대한 포괄적 분석과 회로 최적화를 통하여 주파수 합성기의 저잡음 출력을 방해하지 않는 방법을 고안하였다. 해당 프로토타입 칩은 40-nm CMOS 공정으로 구현되었으며, 전원 노이즈가 인가되지 않은 상태에서 289 fs의 rms 지터를 가지는 8 GHz의 클락을 출력한다. 또한, 20 mVrms의 전원 노이즈가 인가되었을 때에 유도되는 지터의 양을 -23.8 dB 만큼 줄이는 것을 확인하였다.1 Introduction 1 1.1 Motivation 3 1.1.1 Clocking in High-Speed Serial Links 4 1.1.2 Multi-Phase, High-Frequency Clock Conversion 8 1.2 Dissertation Objectives 10 2 RO-Based High-Frequency Synthesis 12 2.1 Phase-Locked Loop Fundamentals 12 2.2 Toward All-Digital Regime 15 2.3 RO Design Challenges 21 2.3.1 Oscillator Phase Noise 21 2.3.2 Challenge 1: High Flicker Noise 23 2.3.3 Challenge 2: High Supply Noise Sensitivity 26 3 Filtering RO Noise 28 3.1 Introduction 28 3.2 Proposed Reference Octupler 34 3.2.1 Delay Constraint 34 3.2.2 Phase Error Calibration 38 3.2.3 Circuit Implementation 51 3.3 IL-ADPLL Implementation 55 3.4 Measurement Results 59 3.5 Summary 63 4 RO Supply Noise Compensation 69 4.1 Introduction 69 4.2 Proposed Analog Closed Loop for Supply Noise Compensation 72 4.2.1 Circuit Implementation 73 4.2.2 Frequency-Domain Analysis 76 4.2.3 Circuit Optimization 81 4.3 ADPLL Implementation 87 4.4 Measurement Results 90 4.5 Summary 98 5 Conclusions 99 A Notes on the 8REF 102 B Notes on the ACSC 105박

All-Digital Phase-Locked Loop for Radio Frequency Synthesis

It has been a constant challenge in wireless system design to meet the growing demand for an ever higher data rate and more diversified functionality at minimal cost and power consumption. The key lies in exploiting the phenomenal success of CMOS technology scaling for high-level integration. This underlies the paradigm shift in the field of integrated circuit (IC) design to one that increasingly favours digital circuits as opposed to their analog counterparts. With radio transceiver design for wireless systems in particular, a noticeable trend is the introduction of digital-intensive solutions for traditional analog functions. A prominent example is the emergence of the all-digital phase-locked loop (ADPLL) architectures for frequency synthesis. By avoiding traditional analog blocks, the ADPLL brings the benefits of high-level integration and improved programmability. This thesis presents ADPLL frequency synthesizer design, highlighting practical design considerations and technical innovations. Three prototype designs using a 65-nm CMOS technology are presented. The first example address a low-power ADPLL design for 2.4-GHz ISM (Industrial, Scientific, Medical) band frequency synthesis. A high-speed topology is employed in the implementation for the variable phase accumulator to count full cycles of the radio frequency (RF) output. A simple technique based on a short delay line in the reference signal path allows the time-to-digital converter (TDC) core to operate at a low duty cycle with approximately 95% reduction in its average power consumption. The ADPLL incorporates a two-point modulation scheme with an adaptive gain calibration to allow for direct frequency modulation. The second implementation is a wide-band ADPLL-based frequency synthesizer for cognitive radio sensor units. It employs a digitally controlled ring oscillator with an LC tank introduced to extend the tuning range and reduce power dissipation. An adaptive frequency calibration technique based on binary search is used for fast frequency settling. The third implementation is another wideband ADPLL frequency synthesizer. At the architectural level, separation of coarse-tune and fine-tune branches results in a word length reduction for both of them and allows the coarse tuning logic to be powered off or clock gated during normal operation, which led to a significant reduction in the area and power consumption for the digital logic and simplified the digital design. A dynamic binary search technique was proposed to achieve further improved frequency calibration speed compared with previous techniques. In addition, an original technique was employed for the frequency tuning of the wideband ring oscillator to allow for compact design and excellent linearity

LOW-JITTER AND LOW-SPUR RING-OSCILLATOR-BASED PHASE-LOCKED LOOPS

Department of Electrical EngineeringIn recent years, ring-oscillator based clock generators have drawn a lot of attention due to the merits of high area efficiency, potentially wide tuning range, and multi-phase generation. However, the key challenge is how to suppress the poor jitter of ring oscillators. There have been many efforts to develop a ring-oscillator-based clock generator targeting very low-jitter performance. However, it remains difficult for conventional architectures to achieve both low RMS jitter and low levels of reference spurs concurrently while having a high multiplication factor. In this dissertation, a time-domain analysis is presented that provides an intuitive understanding of RMS jitter calculation of the clock generators from their phase-error correction mechanisms. Based on this analysis, we propose new designs of a ring-oscillator-based PLL that addresses the challenges of prior-art ring-based architectures. This dissertation introduces a ring-oscillator-based PLL with the proposed fast phase-error correction (FPEC) technique, which emulates the phase-realignment mechanism of an injection-locked clock multiplier (ILCM). With the FPEC technique, the phase error of the voltage-controlled oscillator (VCO) is quickly removed, achieving ultra-low jitter. In addition, in the transfer function of the proposed architecture, an intrinsic integrator is involved since it is naturally based on a PLL topology. The proposed PLL can thus have low levels of reference spurs while maintaining high stability even for a large multiplication factor. Furthermore, it presents another design of a digital PLL embodying the FPEC technique (or FPEC DPLL). To overcome the problem of a conventional TDC, a low-power optimally-spaced (OS) TDC capable of effectively minimizing the quantization error is presented. In the proposed FPEC DPLL, background digital controllers continuously calibrate the decision thresholds and the gain of the error correction by the loop to be optimal, thus dramatically reducing the quantization error. Since the proposed architecture is implemented in a digital fashion, the variables defining the characteristics of the loop can be easily estimated and calibrated by digital calibrators. As a result, the performances of an ultra-low jitter and the figure-of-merit can be achieved.clos