A 10-b Fourth-Order Quadrature Bandpass Continuous-Time ΣΔ Modulator With 33-MHz Bandwidth for a Dual-Channel GNSS Receiver

This document is the Accepted Manuscript version of the following article: Junfeng Zhang, Yang Xu, Zehong Zhang, Yichuang Sun, Zhihua Wang, and Baoyong Chi, ‘A 10-b Fourth-Order Quadrature Bandpass Continuous-Time ΣΔ Modulator With 33-MHz Bandwidth for a Dual-Channel GNSS Receiver’, IEEE Transactions on Microwave Theory and Practice, Vol. 65 (4): 1303-1314, first published online 16 February 2017. The version of record is available online at DOI: 10.1109/TMTT.2017.266237, Published by IEEE. © 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.A fourth-order quadrature bandpass continuous-time sigma-delta modulator for a dual-channel global navigation satellite system (GNSS) receiver is presented. With a bandwidth (BW) of 33 MHz, the modulator is able to digitalize the downconverted GNSS signals in two adjacent signal bands simultaneously, realizing dual-channel GNSS reception with one receiver channel instead of two independent receiver channels. To maintain the loop-stability of the high-order architecture, any extra loop phase shifting should be minimized. In the system architecture, a feedback and feedforward hybrid architecture is used to implement the fourth-order loop-filter, and a return-to-zero (RZ) feedback after the discrete-time differential operation is introduced into the input of the final integrator to realize the excess loop delay compensation, saving a spare summing amplifier. In the circuit implementation, power-efficient amplifiers with high-frequency active feedforward and antipole-splitting techniques are employed in the active RC integrators, and self-calibrated comparators are used to implement the low-power 3-b quantizers. These power saving techniques help achieve superior figure of merit for the presented modulator. With a sampling rate of 460 MHz, current-steering digital-analog converters are chosen to guarantee high conversion speed. Implemented in only 180-nm CMOS, the modulator achieves 62.1-dB peak signal to noise and distortion ratio, 64-dB dynamic range, and 59.3-dB image rejection ratio, with a BW of 33 MHz, and consumes 54.4 mW from a 1.8 V power supply.Peer reviewe

Design and implementation of a wideband sigma delta ADC

Abstract. High-speed and wideband ADCs have become increasingly important in response to the growing demand for high-speed wireless communication services. Continuous time sigma delta modulators (CTƩ∆M), well-known for their oversampling and noise shaping properties, offer a promising solution for low-power and high-speed design in wireless applications. The objective of this thesis is to design and implement a wideband CTƩ∆M for a global navigation satellite system(GNSS) receiver. The targeted modulator architecture is a 3rdorder single-bit CTƩ∆M, specifically designed to operate within a 15 MHz signal bandwidth. With an oversampling ratio of 25, the ADC’s sampling frequency is set at 768 MHz. The design goal is to achieve a theoretical signal to noise ratio (SNR) of 55 dB. This thesis focuses on the design and implementation of the CTƩ∆M, building upon the principles of a discrete time Ʃ∆ modulator, and leveraging system-level simulation and formulations. A detailed explanation of the coefficient calculation procedure specific to CTƩ∆ modulators is provided, along with a "top-down" design approach that ensures the specified requirements are met. MATLAB scripts for coefficient calculation are also included. To overcome the challenges associated with the implementation of CTƩ∆ modulators, particularly excess loop delay and clock jitter sensitivity, this thesis explores two key strategies: the introduction of a delay compensation path and the utilization of a finite impulse response (FIR) feedback DAC. By incorporating a delay compensation path, the stability of the modulator can be ensured and its noise transfer function (NTF) can be restored. Additionally, the integration of an FIR feedback DAC addresses the issue of clock jitter sensitivity, enhancing the overall performance and robustness of the CTƩ∆M. The CTƩ∆Ms employ the cascade of integrators with feed forward (CIFF) and cascade of integrators with feedforward and feedback (CIFF-B) topologies, with a particular emphasis on the CIFF-B configuration using 22nm CMOS technology node and a supply voltage of 0.8 V. Various simulations are performed to validate the modulator’s performance. The simulation results demonstrate an achievable SNR of 55 dB with a power consumption of 1.36 mW. Furthermore, the adoption of NTF zero optimization techniques enhances the SNR to 62 dB.Laajakaistaisen jatkuva-aikaisen sigma delta-AD-muuntimen suunnittelu ja toteutus. Tiivistelmä. Nopeat ja laajakaistaiset AD-muuntimet ovat tulleet entistä tärkeämmiksi nopeiden langattomien kommunikaatiopalvelujen kysynnän kasvaessa. Jatkuva-aikaiset sigma delta -modulaattorit (CTƩ∆M), joissa käytetään ylinäytteistystä ja kohinanmuokkausta, tarjoavat lupaavan ratkaisun matalan tehonkulutuksen ja nopeiden langattomien sovellusten suunnitteluun. Tämän työn tarkoituksena on suunnitella ja toteuttaa laajakaistainen jatkuva -aikainen sigma delta -modulaattori satelliittipaikannusjärjestelmien (GNSS) vastaanottimeen. Arkkitehtuuriltaan modulaattori on kolmannen asteen 1-bittinen CTƩ∆M, jolla on 15MHz:n signaalikaistanleveys. Ylinäytteistyssuhde on 25 ja AD muuntimen näytteistystaajuus 768 MHz. Tavoitteena on saavuttaa teoreettinen 55 dB signaalikohinasuhde (SNR). Tämä työ keskittyy jatkuva-aikaisen sigma delta -modulaattorin suunnitteluun ja toteutukseen, perustuen diskreettiaikaisen Ʃ∆-modulaattorin periaatteisiin ja systeemitason simulointiin ja mallitukseen. Jatkuva-aikaisen sigma delta -modulaattorin kertoimien laskentamenetelmä esitetään yksityiskohtaisesti, ja vaatimusten täyttyminen varmistetaan “top-down” -suunnitteluperiaatteella. Liitteenä on kertoimien laskemiseen käytetty MATLAB-koodi. Jatkuva-aikaisten sigma delta -modulaattoreiden erityishaasteiden, liian pitkän silmukkaviiveen ja kellojitterin herkkyyden, voittamiseksi tutkitaan kahta strategiaa, viiveen kompensointipolkua ja FIR takaisinkytkentä -DA muunninta. Viivekompensointipolkua käyttämällä modulaattorin stabiilisuus ja kohinansuodatusfunktio saadaan varmistettua ja korjattua. Lisäksi FIR takaisinkytkentä -DA-muuntimen käyttö pienentää kellojitteriherkkyyttä, parantaen jatkuva aikaisen sigma delta -modulaattorin kokonaissuorituskykyä ja luotettavuutta. Toteutetuissa jatkuva-aikaisissa sigma delta -modulaattoreissa on kytketty peräkkäin integraattoreita myötäkytkentärakenteella (CIFF) ja toisessa sekä myötä- että takaisinkytkentärakenteella (CIFF-B). Päähuomio on CIFF-B rakenteessa, joka toteutetaan 22nm CMOS prosessissa käyttäen 0.8 voltin käyttöjännitettä. Suorityskyky varmistetaan erilaisilla simuloinneilla, joiden perusteella 55 dB SNR saavutetaan 1.36 mW tehonkulutuksella. Lisäksi kohinanmuokkausfunktion optimoinnilla SNR saadaan nostettua 62 desibeliin

Design of a Comparator and an Amplifier in CMOS using standard logic gates

Using standard logic gates in CMOS, or standard-cells, has the advantage of full synthe- sizability, as well as the voltage scalability between technologies. In this work a general pur- pose standard-cell-based voltage comparator and amplifier are presented. The objective is to design a general purpose standard-cell-based comparator and ampli- fier in 130 nm CMOS by optimizing the already existing topologies with the aim of improving some of the specifications of the studied topologies. Various simulation testbenches were made to test the studied topologies of comparators and amplifiers, in which the results were compared. The top performing standard-cell com- parator and amplifier were then modified. After successfully designing the comparator, it was used in the design of an opamp-less Sigma-Delta modulator (ΣΔM). The proposed comparator is an OR-AND-Inverter-based comparator with dual inputs and outputs, achieving a delay of 109 ps, static input offset of 591 μV, and random offset of 10.42 μV, while dissipating 890 μW, when clocked at 1.5 GHz. The proposed amplifier is a single-path three-stage inverter-based operational transcon- ductance amplifier (OTA) with active common-mode feedback loop, achieving a DC gain of 63 dB, 1444 MHz of unity-gain bandwidth, 51º of phase margin while dissipating 1098 μW, considering a load of 1 pF. The proposed comparator was employed in the ΣΔM with a standard-cell based edge- triggered flip-flop. The ΣΔM, with a sampling frequency of 2 MHz and a signal bandwidth of 2.5 kHz, achieved a peak SNDR of 69 dB while dissipating only 136.7 μW.Utilizando portas lógicas básicas em CMOS oferece a vantagem de um circuito comple- tamente sintetizável, tal como o escalamento de tensão entre tecnologias. Neste trabalho são apresentados um comparador de tensão e um amplificador utilizando portas lógicas. O objetivo deste trabalho é desenhar um comparador e um amplificador utilizando por- tas lógicas através do estudo e otimização de topologias já existentes com a finalidade de me- lhoramento de algumas das especificações das mesmas. Foram realizados vários bancos de teste para testar as topologias estudadas de compa- radores e amplificadores, em que os resultados foram comparados. As topologias de compa- radores e amplificadores de portas lógicas com melhor performance foram então modificadas. Após o comparador ter sido projetado com sucesso, foi utilizado na projeção de um modula- dor Sigma-Delta (ΣΔM) opamp-less. O comparador proposto é um OR-AND-Inversor com duas entradas e saídas, que apre- senta um atraso de 109 ps, offset estático na entrada de 591 μV, offset aleatório de 10.42 μV, enquanto dissipando 890 μW, utilizando uma frequência de relógio de 1.5 GHz O amplificador proposto é um amplificador operacional de transcondutância single- path three-stage inverter-based com um loop ativo de realimentação do modo-comum, que apresenta um ganho DC de 63 dB, 1444 MHz de ganho-unitário de largura de banda, 51º de margem de fase e dissipando 1098 μW, considerando uma carga de 1 pF. O comparador proposto foi aplicado no ΣΔM com um flip-flop edge-triggered baseado em portas lógicas. O ΣΔM, com uma frequência de amostragem de 2 MHz e uma largura de banda de 2.5 kHz, apresentou um SNDR máximo de 69 dB enquanto dissipando apenas 136.7 μW

A 0.1–5.0 GHz flexible SDR receiver with digitally assisted calibration in 65 nm CMOS

© 2017 Elsevier Ltd. All rights reserved.A 0.1–5.0 GHz flexible software-defined radio (SDR) receiver with digitally assisted calibration is presented, employing a zero-IF/low-IF reconfigurable architecture for both wideband and narrowband applications. The receiver composes of a main-path based on a current-mode mixer for low noise, a high linearity sub-path based on a voltage-mode passive mixer for out-of-band rejection, and a harmonic rejection (HR) path with vector gain calibration. A dual feedback LNA with “8” shape nested inductor structure, a cascode inverter-based TCA with miller feedback compensation, and a class-AB full differential Op-Amp with Miller feed-forward compensation and QFG technique are proposed. Digitally assisted calibration methods for HR, IIP2 and image rejection (IR) are presented to maintain high performance over PVT variations. The presented receiver is implemented in 65 nm CMOS with 5.4 mm2 core area, consuming 9.6–47.4 mA current under 1.2 V supply. The receiver main path is measured with +5 dB m/+5dBm IB-IIP3/OB-IIP3 and +61dBm IIP2. The sub-path achieves +10 dB m/+18dBm IB-IIP3/OB-IIP3 and +62dBm IIP2, as well as 10 dB RF filtering rejection at 10 MHz offset. The HR-path reaches +13 dB m/+14dBm IB-IIP3/OB-IIP3 and 62/66 dB 3rd/5th-order harmonic rejection with 30–40 dB improvement by the calibration. The measured sensitivity satisfies the requirements of DVB-H, LTE, 802.11 g, and ZigBee.Peer reviewedFinal Accepted Versio

Design Techniques for High Speed Low Voltage and Low Power Non-Calibrated Pipeline Analog to Digital Converters

The profound digitization of modern microelectronic modules made Analog-to- Digital converters (ADC) key components in many systems. With resolutions up to 14bits and sampling rates in the 100s of MHz, the pipeline ADC is a prime candidate for a wide range of applications such as instrumentation, communications and consumer electronics. However, while past work focused on enhancing the performance of the pipeline ADC from an architectural standpoint, little has been done to individually address its fundamental building blocks. This work aims to achieve the latter by proposing design techniques to improve the performance of these blocks with minimal power consumption in low voltage environments, such that collectively high performance is achieved in the pipeline ADC. Towards this goal, a Recycling Folded Cascode (RFC) amplifier is proposed as an enhancement to the general performance of the conventional folded cascode. Tested in Taiwan Semiconductor Manufacturing Company (TSMC) 0.18?m Complementary Metal Oxide Semiconductor (CMOS) technology, the RFC provides twice the bandwidth, 8-10dB additional gain, more than twice the slew rate and improved noise performance over the conventional folded cascode-all at no additional power or silicon area. The direct auto-zeroing offset cancellation scheme is optimized for low voltage environments using a dual level common mode feedback (CMFB) circuit, and amplifier differential offsets up to 50mV are effectively cancelled. Together with the RFC, the dual level CMFB was used to implement a sample and hold amplifier driving a singleended load of 1.4pF and using only 2.6mA; at 200MS/s better than 9bit linearity is achieved. Finally a power conscious technique is proposed to reduce the kickback noise of dynamic comparators without resorting to the use of pre-amplifiers. When all techniques are collectively used to implement a 1Vpp 10bit 160MS/s pipeline ADC in Semiconductor Manufacturing International Corporation (SMIC) 0.18[mu]m CMOS, 9.2 effective number of bits (ENOB) is achieved with a near Nyquist-rate full scale signal. The ADC uses an area of 1.1mm2 and consumes 42mW in its analog core. Compared to recent state-of-the-art implementations in the 100-200MS/s range, the presented pipeline ADC uses the least power per conversion rated at 0.45pJ/conversion-step

High gain and bandwidth current-mode amplifiers : study and implementation

Doutoramento em Engenharia ElectrotécnicaEsta tese aborda o problema do projecto de amplificadores com grandes produtos de ganho por largura de banda. A aplicação final considerada consistiu no projecto de amplificadores adequados à recepção de sinais ópticos em sistemas de transmissão ópticos usando o espaço livre. Neste tipo de sistemas as maiores limitações de ganho e largura de banda surgem nos circuitos de entrada. O uso de detectores ópticos com grande área fotosensível é uma necessidade comum neste tipo de sistemas. Estes detectores apresentam grandes capacidades intrínsecas, o que em conjunto com a impedância de entrada apresentada pelo amplificador estabelece sérias restrições no produto do ganho pela largura de banda. As técnicas mais tradicionais para combater este problema recorrem ao uso de amplificadores com retroacção baseados em configurações de transimpedância. Estes amplificadores apresentam baixas impedâncias de entrada devido à acção da retroacção. Contudo, os amplificadores de transimpedância também apresentam uma relação directa entre o ganho e a impedância de entrada. Logo, diminuir a impedância de entrada implica diminuir o ganho. Esta tese propõe duas técnicas novas para combater os problemas referidos. A primeira técnica tem por base uma propriedade fundamental dos amplificadores com retroacção. Em geral, todos os circuitos electrónicos têm tempos de atraso associados, os amplificadores com retroacção não são uma excepção a esta regra. Os tempos de atraso são em geral reconhecidos como elementos instabilizadores neste tipos da amplificadores. Contudo, se usados judiciosamente, este tempos de atraso podem ser explorados como uma forma da aumentar a largura de banda em amplificadores com retroacção. Com base nestas ideias, esta tese apresenta o conceito geral de reatroacção com atraso, como um método de optimização de largura de banda em amplificadores com retroacção. O segundo método baseia-se na destruição da dualidade entre ganho e impedância de entrada existente nos amplificadores de transimpedância. O conceito de adaptação activa em modo de corrente é neste sentido uma forma adequada para separar o detector óptico da entrada do amplificador. De acordo com este conceito, emprega-se um elemento de adaptação em modo de corrente para isolar o detector óptico da entrada do amplificador. Desta forma as tradicionais limitações de ganho e largura de banda podem ser tratadas em separado. Esta tese defende o uso destas técnicas no desenho de amplificadores de transimpedância para sistemas de recepção de sinais ópticos em espaço livre.This thesis addresses the problem of achieving high gain-bandwidth products in amplifiers. The adopted framework consisted on the design of a free-space optical (FSO) front end amplifier able to amplify very small optical signals over large frequency bandwidths. The major gain-bandwidth limitations in FSO front end amplifiers arise due to the input circuitry. Usually, it is necessary to have large area optical detectors in order to maximize signal reception. These detectors have large intrinsic capacitances, which together with the amplifier input impedance poses a severe restriction on the gain-bandwidth product. Traditional techniques to combat this gain-bandwidth limitation resort to feedback amplifiers consisting on transimpedance configurations. These amplifiers have small input impedances due to the feedback action. Nevertheless, transimpedance amplifiers have a direct relation between gain and input impedance. Thus reducing the input impedance usually implies reducing the gain. This thesis advances two new methods suitable to combat the above mentioned problems. The first method is based on a fundamental property of feedback amplifiers. In general, all electronic circuits have associated time delays, and feedback amplifiers are not an exception to this rule. Time delays in feedback amplifiers have been recognized as destabilizing elements. Nevertheless, when used with appropriate care, these delays can be exploited as bandwidth enhancement elements. Based on these ideas, this thesis presents the general concept of delayed feedback, as a bandwidth optimization method suitable for feedback amplifiers. The second method is based on the idea of destroying the impedance-gain duality in transimpedance amplifiers. The concept of active current matching is in this sense a suitable method to detach the optical detector from the transimpedance amplifier input. According to this concept, a current matching device (CMD) is used to convey the signal current sensed by the optical detector, to the amplifier’s input. Using this concept the traditional gainbandwidth limitations can be treated in a separate fashion. This thesis advocates the usage of these techniques for the design of transimpedance amplifiers suited for FSO receiving systems

Design Of A 20MHz Transimpedance Amplifier With Embedded Low-pass Filter For A Direct Conversion Wireless Receiver

Accelerated growth in wireless communications in recent years has led to the emergence of portable devices that employ several wireless communication standards to provide multiple functionality such as cellular communication, wireless data communication and connectivity, entertainment and navigation, within the same device. Industry drive is towards reduction of the number of radio frequency (RF) front-end receivers required to cater to the various standards/bands within a single device to reduce cost, size and power consumption. The current trend is to use broadband/multi-standard or reconfigurable RF front-ends to cater to two or three standards at a time for cost-effective RF front-end solutions. The direct conversion receiver architecture has become attractive as it offers a full on-chip front-end solution without the need for expensive external components. Passive current-mode mixers are used in these receivers to eliminate mixer flicker noise. The in-band current signals are typically in the micro-amp range after mixer downconversion. Transimpedance amplifiers are used to convert the downconverted current signals to voltage, and they provide amplification in the process. Because of the co-existence of multiple-radios within each device, large blocker currents downconvert close to the channel bandwidth after the mixer. Conventionally, single-pole transimpedance amplifier (TIA) filters are used to provide out-of-band (OOB) signal filtering. This requires high resolution analog-to-digital converters (ADCs) later in the receiver chain for signal processing. Providing higher order filtering before the ADC relaxes its specifications and this reduces the ADC and ADC calibration cost and complexity. Typically, an extra filtering stage is provided in the form of a cascaded filtering block after the single-pole TIA. In this work, higher order filtering is embedded within the TIA in the form of active feedback. In addition to relaxing the ADC specifications, this proposed TIA provides improved large signal linearity such as P1dB compression point. Furthermore, since the extra-circuitry is not in the signal path, in-band flicker noise and linearity are not degraded. The proposed TIA filter has been designed in IBM 90nm technology with a supply voltage of 1.2V. It can tolerate close-in blocker magnitudes of 4.5mA at 60MHz and higher before in-band 1dB compression is reached

First Order Self-Oscillating Class-D Circuit with Triangular Wave Injection

An investigation into performance improvements to the modulator stage of a class-D amplifier is conducted in this thesis. Two of the standard topologies, namely class-D open-loop pulse-width modulation (PWM), and the improved self-oscillating feedback system are benchmarked against a topology which includes both a hysteretic comparator in a feedback loop and triangle wave injection. Circuit performance is analyzed by comparing how the triangle injection circuit handles known issues with open-loop and self-oscillating circuits. Using this analysis, it is shown that the triangle injection topology offers an improved power supply rejection ratio relative to open-loop PWM and reduces distortion generated by frequency modulation characteristic of the self-oscillating topology

Performance enhancement techniques for operational amplifiers

Operational amplifiers (op amps) are one of the most fundamental and widely used building blocks for analog and mixed-signal circuits and systems. As transistors’ feature size scales down in the deep submicron process, the short channel effects, high leakage current and reduced supply voltages make the design of op amps more challenging. In this dissertation, we present several methods to improve op amps’ DC gain, slew rate, power efficiency and current utilization efficiency (CUE). A basic requirement for an op amp is high DC gain especially for high precision applications. We introduce a method to robustly improve op amps’ DC gain with negligible power and area overhead. The new DC gain enhancement method can be implemented based on the source degeneration circuit (SDC) or the flipped voltage attenuator (FVA). Compared to the FVA-based technique, the SDC-based technique is more suitable for those CMOS processes whose transistors’ threshold voltages are too low for the transistors in the FVA to work in weak or strong inversion regions. Otherwise, the FVA-based technique is recommended as this technique is more robust to devices’ random mismatch. A prototype op amp with the FVA-based technique is designed and fabricated in the IBM130nm process. The measurement and simulation results of the prototype verify that the technique largely enhances an op amp’s DC and is very robust over process, voltage and temperature variations. Another important op amp requirement is high slew rate. In this regard, we introduce a method that greatly improves an op amp’s slew rate while still preserving its small signal performance by a well-defined turn-on condition. The performance of the introduced method is discussed in comparison with an existing adaptive biasing method that was widely used to enhance slew rate. The introduced method excels in several aspects. First, unlike the adaptive biasing method which degrades an op amp’ linearity, the introduced method is able to enhance linearity. Second, the proposed method improves an op amp’s slew rate by 2320% (vs. 780% by the adaptive method) with the power and area overhead of 2% and 1.2% (vs. 15% and 35% by the adaptive method). In addition, the proposed method improves the op amp’s total harmonic distortion (THD) by 6dB but the adaptive method degrades the THD by 12dB. The ability to drive large capacitive loads is becoming critical for op amps in emerging applications such as liquid crystal display drivers. In this regard, we introduce a power efficient design of op amps that can drive large capacitive loads. The proposed method decouples the large and small signal performance, eliminates current waste in the preamp stages’ load circuits, and is not sensitive to devices’ random mismatches. Compared to the state-of-the-art methods, our design prototype in a CMOS 180nm process shows largely improved small and large signal figure of merits, equivalent to largely improved power efficiency for given small and large signal performance specifications. Folded cascode amplifier (FCA) is a commonly used architecture for designing op amps, but a significant portion of supply current is wasted in the cascode stage. This not only reduces the current utilization efficiency (CUE), defined as the ratio of an FCA’s tail current to its total supply current, but also degrades the FCA’s gain, noise and offset. In this regard, we introduce a method to dramatically reduce a FCA’s cascode stage current without degrading the FCA’s settling performance. Compared to the existing methods, the proposed method effectively improves not only the CUE but also the settling performance of op amps. Lastly, a prototype FCA, with the proposed performance enhancement techniques of gain, slew rate and CUE, is designed to demonstrate the compatibility of these techniques