Silicon-on-Insulator Power Management Integrated Circuit for Thin-Film Solid-State Lithium-Ion Micro-Batteries

This thesis presents the design and implementation of a power management integrated circuit (IC) that is capable of both current and voltage charging thin-film, solid-state, lithium-ion micro-batteries. The power management system has been fabricated using a single-poly, 0.35-ìm, partially-depleted, silicon-on-insulator process (PD-SOI). The system contains a temperature stable current charger (current generator and a 4-bit current-mode DAC), a regulated voltage supply (voltage amplifier), and a voltage monitoring circuit (2-bit flash ADC). Experimental results of the first version of the power management system show proper functionality was obtained. The current charger produced a 2% worst-case variation in output current over the temperature range 0–100°C. The regulated voltage output was measured to be 4.4 V and the digital outputs of the flash ADC transitioned at 3.45 and 4.76 V

An accurate, trimless, high PSRR, low-voltage, CMOS bandgap reference IC

Bandgap reference circuits are used in a host of analog, digital, and mixed-signal systems to establish an accurate voltage standard for the entire IC. The accuracy of the bandgap reference voltage under steady-state (dc) and transient (ac) conditions is critical to obtain high system performance. In this work, the impact of process, power-supply, load, and temperature variations and package stresses on the dc and ac accuracy of bandgap reference circuits has been analyzed. Based on this analysis, the a bandgap reference that 1. has high dc accuracy despite process and temperature variations and package stresses, without resorting to expensive trimming or noisy switching schemes, 2. has high dc and ac accuracy despite power-supply variations, without using large off-chip capacitors that increase bill-of-material costs, 3. has high dc and ac accuracy despite load variations, without resorting to error-inducing buffers, 4. is capable of producing a sub-bandgap reference voltage with a low power-supply, to enable it to operate in modern, battery-operated portable applications, 5. utilizes a standard CMOS process, to lower manufacturing costs, and 6. is integrated, to consume less board space has been proposed. The functionality of critical components of the system has been verified through prototypes after which the performance of the complete system has been evaluated by integrating all the individual components on an IC. The proposed CMOS bandgap reference can withstand 5mA of load variations while generating a reference voltage of 890mV that is accurate with respect to temperature to the first order. It exhibits a trimless, dc 3-sigma accuracy performance of 0.84% over a temperature range of -40°C to 125°C and has a worst case ac power-supply ripple rejection (PSRR) performance of 30dB up to 50MHz using 60pF of on-chip capacitance. All the proposed techniques lead to the development of a CMOS bandgap reference that meets the low-cost, high-accuracy demands of state-of-the-art System-on-Chip environments.Ph.D.Committee Chair: Rincon-Mora, Gabriel; Committee Member: Ayazi, Farrokh; Committee Member: Bhatti, Pamela; Committee Member: Leach, W. Marshall; Committee Member: Morley, Thoma

High Performance Current Amplifier [TK7871.58.P4 G896 2006 f rb] [Microfiche 8561].

A high bandwidth class AB current amplifier by using few compensation resistor technique and current mirrors is presented and analyzed. The simulation results are obtained using TSpice tool using 0.35μm CMOS TSMC process, at 2.5V power supply. The amplifier utilizes Class AB amplifier topology to achieve high bandwidth. Sebuah penguat arus kelas AB berjalur lebar tinggi yang menggunakan teknik “compensation” resistor dibentang dan dianalisis dalam tesis ini. Keputusan penyelakuan ini didapati dengan mengunakan Teknology TSMC 0.35μm CMOS bekalan kuasa 2.5V melalui alat penyelakuan TSPice. Penguat Kelas AB diimplementasikan untuk mencapai jalur lebar yang tinggi

CMOS design of chaotic oscillators using state variables: a monolithic Chua's circuit

This paper presents design considerations for monolithic implementation of piecewise-linear (PWL) dynamic systems in CMOS technology. Starting from a review of available CMOS circuit primitives and their respective merits and drawbacks, the paper proposes a synthesis approach for PWL dynamic systems, based on state-variable methods, and identifies the associated analog operators. The GmC approach, combining quasi-linear VCCS's, PWL VCCS's, and capacitors is then explored regarding the implementation of these operators. CMOS basic building blocks for the realization of the quasi-linear VCCS's and PWL VCCS's are presented and applied to design a Chua's circuit IC. The influence of GmC parasitics on the performance of dynamic PWL systems is illustrated through this example. Measured chaotic attractors from a Chua's circuit prototype are given. The prototype has been fabricated in a 2.4- mu m double-poly n-well CMOS technology, and occupies 0.35 mm/sup 2/, with a power consumption of 1.6 mW for a +or-2.5-V symmetric supply. Measurements show bifurcation toward a double-scroll Chua's attractor by changing a bias current

A wideband linear tunable CDTA and its application in field programmable analogue array

This document is the Accepted Manuscript version of the following article: Hu, Z., Wang, C., Sun, J. et al. ‘A wideband linear tunable CDTA and its application in field programmable analogue array’, Analog Integrated Circuits and Signal Processing, Vol. 88 (3): 465-483, September 2016. Under embargo. Embargo end date: 6 June 2017. The final publication is available at Springer via https://link.springer.com/article/10.1007%2Fs10470-016-0772-7 © Springer Science+Business Media New York 2016In this paper, a NMOS-based wideband low power and linear tunable transconductance current differencing transconductance amplifier (CDTA) is presented. Based on the NMOS CDTA, a novel simple and easily reconfigurable configurable analogue block (CAB) is designed. Moreover, using the novel CAB, a simple and versatile butterfly-shaped FPAA structure is introduced. The FPAA consists of six identical CABs, and it could realize six order current-mode low pass filter, second order current-mode universal filter, current-mode quadrature oscillator, current-mode multi-phase oscillator and current-mode multiplier for analog signal processing. The Cadence IC Design Tools 5.1.41 post-layout simulation and measurement results are included to confirm the theory.Peer reviewedFinal Accepted Versio

CMOS analog-digital circuit components for low power applications

Dissertação de mestrado em Micro and NanoelectronicsThis dissertation presents a study in the area of mixed analog/digital CMOS power extraction circuits for energy harvester. The main contribution of this work is the realization of low power consumption and high efficient circuit components employable in a management circuit for piezoelectricbased energy harvester. This thesis focuses on the development of current references and operational amplifiers addressing low power demands. A brief literature review is conducted on the components necessary for the power extraction circuit, including introduction to CMOS technology design and research of known low power circuits. It is presented with multiple implementations for voltage and current references, as well for operational amplifier designs. A self-biased current reference, capable of driving the remaining harvesting circuit, is designed and verified. A novel operational amplifier is proposed by the use of a minimum current selector circuit topology. It is a three-stage amplifier with an AB class output stage, comprised by a translinear circuit. The circuit is designed, taking into consideration noise reduction. The circuit components are designed based on the 0.35mm CMOS technology. A physical layout is developed for fabrication purposes. This technology was chosen with consideration of robustness, costliness and performance. The current reference is capable of outputting a stable 12nA current, which may remain stable in a broad range of power supply voltages with a minimum voltage of 1.6V. The operational amplifier operates correctly at voltages as low as 1.5V. The amplifier power consumption is extremely low, around 8mW, with an optimal quiescent current and minimum current preservation in the output stage.A principal contribuição desta dissertação é a implementação de circuitos integrados de muito baixo consumo e alta eficiência, prontos a ser implementados num circuito de extração de energia com base num elemento piezoelétrico. Esta tese foca-se no desenvolvimento de um circuito de referência de corrente e um amplificador operacional com baixa exigência de consumo. Uma revisão da literatura é realizada, incluindo introdução à tecnologia Complementary Metal-Oxide-Semiconductor (CMOS), e implementação de conhecidos circuitos de baixo consumo. Várias implementações de referência de tensão e corrente são consideradas, e amplificadores operacionais também. Uma referência de corrente auto polarizada com extremo baixo consumo é desenvolvida e verificada. Um amplificador operacional original é proposto com uma topologia de seleção de corrente mínima. Este circuito é constituído por três estágios, com um estágio de saída de classe AB, e um circuito translinear. O circuito tem em consideração redução de ruído na sua implementação. Os circuitos são desenvolvidos com base na tecnologia 0.35mm CMOS. Uma layout foi também desenhada com o propósito de fabricação. A tecnologia foi escolhida tendo em conta o seu custo versus desempenho. A referência de corrente produz uma corrente de 12nA, permanecendo estável para tensões de alimentação de variáveis, com uma tensão mínima de 1.6V. O circuito mostra um coeficiente de temperatura satisfatório. O amplificador operacional funciona com tensão de alimentação mínima de 1.5V, com um consumo baixo de 8mW, com uma corrente mínima mantida no estágio de saída

A Survey of Non-conventional Techniques for Low-voltage Low-power Analog Circuit Design

Designing integrated circuits able to work under low-voltage (LV) low-power (LP) condition is currently undergoing a very considerable boom. Reducing voltage supply and power consumption of integrated circuits is crucial factor since in general it ensures the device reliability, prevents overheating of the circuits and in particular prolongs the operation period for battery powered devices. Recently, non-conventional techniques i.e. bulk-driven (BD), floating-gate (FG) and quasi-floating-gate (QFG) techniques have been proposed as powerful ways to reduce the design complexity and push the voltage supply towards threshold voltage of the MOS transistors (MOST). Therefore, this paper presents the operation principle, the advantages and disadvantages of each of these techniques, enabling circuit designers to choose the proper design technique based on application requirements. As an example of application three operational transconductance amplifiers (OTA) base on these non-conventional techniques are presented, the voltage supply is only ±0.4 V and the power consumption is 23.5 µW. PSpice simulation results using the 0.18 µm CMOS technology from TSMC are included to verify the design functionality and correspondence with theory

Energy-Efficient Amplifiers Based on Quasi-Floating Gate Techniques

Energy efficiency is a key requirement in the design of amplifiers for modern wireless applications. The use of quasi-floating gate (QFG) transistors is a very convenient approach to achieve such energy efficiency. We illustrate different QFG circuit design techniques aimed to implement low-voltage, energy-efficient class AB amplifiers. A new super class AB QFG amplifier is presented as a design example, including some of the techniques described. The amplifier has been fabricated in a 130 nm CMOS test chip prototype. Measurement results confirm that low-voltage, ultra-low-power amplifiers can be designed, preserving, at the same time, excellent small-signal and large-signal performance.Agencia Estatal de Investigación PID2019-107258RB-C32Unión Europea PID2019-107258RB-C3

Energy-efficient amplifiers based on quasi-floating gate techniques

Energy efficiency is a key requirement in the design of amplifiers for modern wireless applications. The use of quasi-floating gate (QFG) transistors is a very convenient approach to achieve such energy efficiency. We illustrate different QFG circuit design techniques aimed to implement low-voltage energy-efficient class AB amplifiers. A new super class AB QFG amplifier is presented as a design example including some of the techniques described. The amplifier has been fabricated in a 130 nm CMOS test chip prototype. Measurement results confirm that low-voltage ultra low power amplifiers can be designed preserving at the same time excellent small-signal and large-signal performance.This research was funded by AEI/FEDER, grant number PID2019-107258RB-C32