Superposition coded modulation with peak-power limitation

We apply clipping to superposition coded modulation (SCM) systems to reduce the peak-to-average power ratio (PAPR) of the transmitted signal. The impact on performance is investigated by evaluating the mutual information driven by the induced peak-power-limited input signals. It is shown that the rate loss is marginal for moderate clipping thresholds if optimal encoding/decoding is used. This fact is confirmed in examples where capacityapproaching component codes are used together with the maximum a posteriori probability (MAP) detection. In order to reduce the detection complexity of SCM with a large number of layers, we develop a suboptimal soft compensation (SC) method that is combined with soft-input soft-output (SISO) decoding algorithms in an iterative manner. A variety of simulation results for additive white Gaussian noise (AWGN) and fading channels are presented. It is shown that with the proposed method, the effect of clipping can be efficiently compensated and a good tradeoff between PAPR and bit-error rate (BER) can be achieved. Comparisons with other coded modulation schemes demonstrate that SCM offers significant advantages for high-rate transmissions over fading channels

Advanced Coding And Modulation For Ultra-wideband And Impulsive Noises

The ever-growing demand for higher quality and faster multimedia content delivery over short distances in home environments drives the quest for higher data rates in wireless personal area networks (WPANs). One of the candidate IEEE 802.15.3a WPAN proposals support data rates up to 480 Mbps by using punctured convolutional codes with quadrature phase shift keying (QPSK) modulation for a multi-band orthogonal frequency-division multiplexing (MB-OFDM) system over ultra wideband (UWB) channels. In the first part of this dissertation, we combine more powerful near-Shannon-limit turbo codes with bandwidth efficient trellis coded modulation, i.e., turbo trellis coded modulation (TTCM), to further improve the data rates up to 1.2 Gbps. A modified iterative decoder for this TTCM coded MB-OFDM system is proposed and its bit error rate performance under various impulsive noises over both Gaussian and UWB channel is extensively investigated, especially in mismatched scenarios. A robust decoder which is immune to noise mismatch is provided based on comparison of impulsive noises in time domain and frequency domain. The accurate estimation of the dynamic noise model could be very difficult or impossible at the receiver, thus a significant performance degradation may occur due to noise mismatch. In the second part of this dissertation, we prove that the minimax decoder in \cite, which instead of minimizing the average bit error probability aims at minimizing the worst bit error probability, is optimal and robust to certain noise model with unknown prior probabilities in two and higher dimensions. Besides turbo codes, another kind of error correcting codes which approach the Shannon capacity is low-density parity-check (LDPC) codes. In the last part of this dissertation, we extend the density evolution method for sum-product decoding using mismatched noises. We will prove that as long as the true noise type and the estimated noise type used in the decoder are both binary-input memoryless output symmetric channels, the output from mismatched log-likelihood ratio (LLR) computation is also symmetric. We will show the Shannon capacity can be evaluated for mismatched LLR computation and it can be reduced if the mismatched LLR computation is not an one-to-one mapping function. We will derive the Shannon capacity, threshold and stable condition of LDPC codes for mismatched BIAWGN and BIL noise types. The results show that the noise variance estimation errors will not affect the Shannon capacity and stable condition, but the errors do reduce the threshold. The mismatch in noise type will only reduce Shannon capacity when LLR computation is based on BIL

Source-channel coding for robust image transmission and for dirty-paper coding

In this dissertation, we studied two seemingly uncorrelated, but conceptually related problems in terms of source-channel coding: 1) wireless image transmission and 2) Costa ("dirty-paper") code design. In the first part of the dissertation, we consider progressive image transmission over a wireless system employing space-time coded OFDM. The space-time coded OFDM system based on a newly built broadband MIMO fading model is theoretically evaluated by assuming perfect channel state information (CSI) at the receiver for coherent detection. Then an adaptive modulation scheme is proposed to pick the constellation size that offers the best reconstructed image quality for each average signal-to-noise ratio (SNR). A more practical scenario is also considered without the assumption of perfect CSI. We employ low-complexity decision-feedback decoding for differentially space- time coded OFDM systems to exploit transmitter diversity. For JSCC, we adopt a product channel code structure that is proven to provide powerful error protection and bursty error correction. To further improve the system performance, we also apply the powerful iterative (turbo) coding techniques and propose the iterative decoding of differentially space-time coded multiple descriptions of images. The second part of the dissertation deals with practical dirty-paper code designs. We first invoke an information-theoretical interpretation of algebraic binning and motivate the code design guidelines in terms of source-channel coding. Then two dirty-paper code designs are proposed. The first is a nested turbo construction based on soft-output trellis-coded quantization (SOTCQ) for source coding and turbo trellis- coded modulation (TTCM) for channel coding. A novel procedure is devised to balance the dimensionalities of the equivalent lattice codes corresponding to SOTCQ and TTCM. The second dirty-paper code design employs TCQ and IRA codes for near-capacity performance. This is done by synergistically combining TCQ with IRA codes so that they work together as well as they do individually. Our TCQ/IRA design approaches the dirty-paper capacity limit at the low rate regime (e.g., < 1:0 bit/sample), while our nested SOTCQ/TTCM scheme provides the best performs so far at medium-to-high rates (e.g., >= 1:0 bit/sample). Thus the two proposed practical code designs are complementary to each other

Spectrally and Energy Efficient Wireless Communications: Signal and System Design, Mathematical Modelling and Optimisation

This thesis explores engineering studies and designs aiming to meeting the requirements of enhancing capacity and energy efficiency for next generation communication networks. Challenges of spectrum scarcity and energy constraints are addressed and new technologies are proposed, analytically investigated and examined. The thesis commences by reviewing studies on spectrally and energy-efficient techniques, with a special focus on non-orthogonal multicarrier modulation, particularly spectrally efficient frequency division multiplexing (SEFDM). Rigorous theoretical and mathematical modelling studies of SEFDM are presented. Moreover, to address the potential application of SEFDM under the 5th generation new radio (5G NR) heterogeneous numerologies, simulation-based studies of SEFDM coexisting with orthogonal frequency division multiplexing (OFDM) are conducted. New signal formats and corresponding transceiver structure are designed, using a Hilbert transform filter pair for shaping pulses. Detailed modelling and numerical investigations show that the proposed signal doubles spectral efficiency without performance degradation, with studies of two signal formats; uncoded narrow-band internet of things (NB-IoT) signals and unframed turbo coded multi-carrier signals. The thesis also considers using constellation shaping techniques and SEFDM for capacity enhancement in 5G system. Probabilistic shaping for SEFDM is proposed and modelled to show both transmission energy reduction and bandwidth saving with advantageous flexibility for data rate adaptation. Expanding on constellation shaping to improve performance further, a comparative study of multidimensional modulation techniques is carried out. A four-dimensional signal, with better noise immunity is investigated, for which metaheuristic optimisation algorithms are studied, developed, and conducted to optimise bit-to-symbol mapping. Finally, a specially designed machine learning technique for signal and system design in physical layer communications is proposed, utilising the application of autoencoder-based end-to-end learning. Multidimensional signal modulation with multidimensional constellation shaping is proposed and optimised by using machine learning techniques, demonstrating significant improvement in spectral and energy efficiencies

An investigation into the use of orthogonal frequency division multiplexing in packet radio

Bibliography: leaves 56-58.The concept of Orthogonal Frequency Division Multiplexing has been around since the 1960s. It has resurfaced over the last decade as being the modulation scheme of choice in some newer technologies like Digital Video Broadcasting (DVB) and Asynchronous Digital Subscriber lines (ADSL). Amateur packet radio started in 1978 and has attracted thousands of enthusiasts from around the world. The interest in packet radio has waned over the years due advances in the data transmission capabilities oflandline systems and also more widespread access to the Internet. The purpose of this thesis was to develop a simple software simulation model to determine whether or not OFDM could be used to increase the data rates currently available in packet radio systems. The thesis starts out with an introduction to packet radio and OFDM in Chapter 1. A slightly more detailed discussion on OFDM is given in Chapter 2 in order to develop a basic specification for the proposed OFDM model. Chapters 2,3 and 4 discuss the development of the Transmitter model, the Receiver model and the Channel model respectively using the Simulink software package. Chapter 6 discusses the problem of Peak-to-Average Power Ratios (PAPR) in OFDM and explores the use of A-law companding to reduce this problem. In Chapter 7, the developed models are simulated and their performance compared to theoretical expectations. The full system is also simulated in this chapter in order to ascertain the possible data rate through the modelled packet radio channel. Conclusions regarding the application of OFDM to packet radio are presented in Chapter 8

THE APPLICATION OF REAL-TIME SOFTWARE IN THE IMPLEMENTATION OF LOW-COST SATELLITE RETURN LINKS

Digital Signal Processors (DSPs) have evolved to a level where it is feasible for digital modems with relatively low data rates to be implemented entirely with software algorithms. With current technology it is still necessary for analogue processing between the RF input and a low frequency IF but, as DSP technology advances, it will become possible to shift the interface between analogue and digital domains ever closer towards the RF input. The software radio concept is a long-term goal which aims to realise software-based digital modems which are completely flexible in terms of operating frequency, bandwidth, modulation format and source coding. The ideal software radio cannot be realised until DSP, Analogue to Digital (A/D) and Digital to Analogue (D/A) technology has advanced sufficiently. Until these advances have been made, it is often necessary to sacrifice optimum performance in order to achieve real-time operation. This Thesis investigates practical real-time algorithms for carrier frequency synchronisation, symbol timing synchronisation, modulation, demodulation and FEC. Included in this work are novel software-based transceivers for continuous-mode transmission, burst-mode transmission, frequency modulation, phase modulation and orthogonal frequency division multiplexing (OFDM). Ideal applications for this work combine the requirement for flexible baseband signal processing and a relatively low data rate. Suitable applications for this work were identified in low-cost satellite return links, and specifically in asymmetric satellite Internet delivery systems. These systems employ a high-speed (>>2Mbps) DVB channel from service provider to customer and a low-cost, low-speed (32-128 kbps) return channel. This Thesis also discusses asymmetric satellite Internet delivery systems, practical considerations for their implementation and the techniques that are required to map TCP/IP traffic to low-cost satellite return links

Advanced receivers and waveforms for UAV/Aircraft aeronautical communications

Nowadays, several studies are launched for the design of reliable and safe communications systems that introduce Unmanned Aerial Vehicle (UAV), this paves the way for UAV communication systems to play an important role in a lot of applications for non-segregated military and civil airspaces. Until today, rules for integrating commercial UAVs in airspace still need to be defined, the design of secure, highly reliable and cost effective communications systems still a challenging task. This thesis is part of this communication context. Motivated by the rapid growth of UAV quantities and by the new generations of UAVs controlled by satellite, the thesis aims to study the various possible UAV links which connect UAV/aircraft to other communication system components (satellite, terrestrial networks, etc.). Three main links are considered: the Forward link, the Return link and the Mission link. Due to spectrum scarcity and higher concentration in aircraft density, spectral efficiency becomes a crucial parameter for largescale deployment of UAVs. In order to set up a spectrally efficient UAV communication system, a good understanding of transmission channel for each link is indispensable, as well as a judicious choice of the waveform. This thesis begins to study propagation channels for each link: a mutipath channels through radio Line-of-Sight (LOS) links, in a context of using Meduim Altitude Long drones Endurance (MALE) UAVs. The objective of this thesis is to maximize the solutions and the algorithms used for signal reception such as channel estimation and channel equalization. These algorithms will be used to estimate and to equalize the existing muti-path propagation channels. Furthermore, the proposed methods depend on the choosen waveform. Because of the presence of satellite link, in this thesis, we consider two low-papr linear waveforms: classical Single-Carrier (SC) waveform and Extented Weighted Single-Carrier Orthogonal Frequency-Division Multiplexing (EW-SC-OFDM) waveform. channel estimation and channel equalization are performed in the time-domain (SC) or in the frequency-domain (EW-SC-OFDM). UAV architecture envisages the implantation of two antennas placed at wings. These two antennas can be used to increase diversity gain (channel matrix gain). In order to reduce channel equalization complexity, the EWSC- OFDM waveform is proposed and studied in a muti-antennas context, also for the purpose of enhancing UAV endurance and also increasing spectral efficiency, a new modulation technique is considered: Spatial Modulation (SM). In SM, transmit antennas are activated in an alternating manner. The use of EW-SC-OFDM waveform combined to SM technique allows us to propose new modified structures which exploit exces bandwidth to improve antenna bit protection and thus enhancing system performances

Repeat-Accumulate構造に基づく直列連接信号符号

電気通信大学201

Architecture and algorithms for the implementation of digital wireless receivers in FPGA and ASIC: ISDB-T and DVB-S2 cases

[EN] The first generation of Terrestrial Digital Television(DTV) has been in service for over a decade. In 2013, several countries have already completed the transition from Analog to Digital TV Broadcasting, most of which in Europe. In South America, after several studies and trials, Brazil adopted the Japanese standard with some innovations. Japan and Brazil started Digital Terrestrial Television Broadcasting (DTTB) services in December 2003 and December 2007 respectively, using Integrated Services Digital Broadcasting - Terrestrial (ISDB-T), also known as ARIB STD-B31. In June 2005 the Committee for the Information Technology Area (CATI) of Brazilian Ministry of Science and Technology and Innovation MCTI approved the incorporation of the IC-Brazil Program, in the National Program for Microelectronics (PNM) . The main goals of IC-Brazil are the formal qualification of IC designers, support to the creation of semiconductors companies focused on projects of ICs within Brazil, and the attraction of semiconductors companies focused on the design and development of ICs in Brazil. The work presented in this thesis originated from the unique momentum created by the combination of the birth of Digital Television in Brazil and the creation of the IC-Brazil Program by the Brazilian government. Without this combination it would not have been possible to make these kind of projects in Brazil. These projects have been a long and costly journey, albeit scientifically and technologically worthy, towards a Brazilian DTV state-of-the-art low complexity Integrated Circuit, with good economy scale perspectives, due to the fact that at the beginning of this project ISDB-T standard was not adopted by several countries like DVB-T. During the development of the ISDB-T receiver proposed in this thesis, it was realized that due to the continental dimensions of Brazil, the DTTB would not be enough to cover the entire country with open DTV signal, specially for the case of remote localizations far from the high urban density regions. Then, Eldorado Research Institute and Idea! Electronic Systems, foresaw that, in a near future, there would be an open distribution system for high definition DTV over satellite, in Brazil. Based on that, it was decided by Eldorado Research Institute, that would be necessary to create a new ASIC for broadcast satellite reception. At that time DVB-S2 standard was the strongest candidate for that, and this assumption still stands nowadays. Therefore, it was decided to apply to a new round of resources funding from the MCTI - that was granted - in order to start the new project. This thesis discusses in details the Architecture and Algorithms proposed for the implementation of a low complexity Intermediate Frequency(IF) ISDB-T Receiver on Application Specific Integrated Circuit (ASIC) CMOS. The Architecture proposed here is highly based on the COordinate Rotation Digital Computer (CORDIC) Algorithm, that is a simple and efficient algorithm suitable for VLSI implementations. The receiver copes with the impairments inherent to wireless channels transmission and the receiver crystals. The thesis also discusses the Methodology adopted and presents the implementation results. The receiver performance is presented and compared to those obtained by means of simulations. Furthermore, the thesis also presents the Architecture and Algorithms for a DVB-S2 receiver targeting its ASIC implementation. However, unlike the ISDB-T receiver, only preliminary ASIC implementation results are introduced. This was mainly done in order to have an early estimation of die area to prove that the project in ASIC is economically viable, as well as to verify possible bugs in early stage. As in the case of ISDB-T receiver, this receiver is highly based on CORDIC algorithm and it was prototyped in FPGA. The Methodology used for the second receiver is derived from that used for the ISDB-T receiver, with minor additions given the project characteristics.[ES] La primera generación de Televisión Digital Terrestre(DTV) ha estado en servicio por más de una década. En 2013, varios países completaron la transición de transmisión analógica a televisión digital, la mayoría de ellas en Europa. En América del Sur, después de varios estudios y ensayos, Brasil adoptó el estándar japonés con algunas innovaciones. Japón y Brasil comenzaron a prestar el servicio de Difusión de Televisión Digital Terrestre (DTTB) en diciembre de 2003 y diciembre de 2007 respectivamente, utilizando Radiodifusión Digital de Servicios Integrados Terrestres (ISDB-T), también conocida como ARIB STD-B31. En junio de 2005, el Comité del Área de Tecnología de la Información (CATI) del Ministerio de Ciencia, Tecnología e Innovación de Brasil - MCTI aprobó la incorporación del Programa CI-Brasil, en el Programa Nacional de Microelectrónica (PNM). Los principales objetivos de la CI-Brasil son la formación de diseñadores de CIs, apoyar la creación de empresas de semiconductores enfocadas en proyectos de circuitos integrados dentro de Brasil, y la atracción de empresas de semiconductores interesadas en el diseño y desarrollo de circuitos integrados. El trabajo presentado en esta tesis se originó en el impulso único creado por la combinación del nacimiento de la televisión digital en Brasil y la creación del Programa de CI-Brasil por el gobierno brasileño. Sin esta combinación no hubiera sido posible realizar este tipo de proyectos en Brasil. Estos proyectos han sido un trayecto largo y costoso, aunque meritorio desde el punto de vista científico y tecnológico, hacia un Circuito Integrado brasileño de punta y de baja complejidad para DTV, con buenas perspectivas de economía de escala debido al hecho que al inicio de este proyecto, el estándar ISDB-T no fue adoptado por varios países como DVB-T. Durante el desarrollo del receptor ISDB-T propuesto en esta tesis, se observó que debido a las dimensiones continentales de Brasil, la DTTB no sería suficiente para cubrir todo el país con la señal de televisión digital abierta, especialmente para el caso de localizaciones remotas, apartadas de las regiones de alta densidad urbana. En ese momento, el Instituto de Investigación Eldorado e Idea! Sistemas Electrónicos, previeron que en un futuro cercano habría un sistema de distribución abierto para DTV de alta definición por satélite en Brasil. Con base en eso, el Instituto de Investigación Eldorado decidió que sería necesario crear un nuevo ASIC para la recepción de radiodifusión por satélite, basada el estándar DVB-S2. En esta tesis se analiza en detalle la Arquitectura y algoritmos propuestos para la implementación de un receptor ISDB-T de baja complejidad y frecuencia intermedia (IF) en un Circuito Integrado de Aplicación Específica (ASIC) CMOS. La arquitectura aquí propuesta se basa fuertemente en el algoritmo Computadora Digital para Rotación de Coordenadas (CORDIC), el cual es un algoritmo simple, eficiente y adecuado para implementaciones VLSI. El receptor hace frente a las deficiencias inherentes a las transmisiones por canales inalámbricos y los cristales del receptor. La tesis también analiza la metodología adoptada y presenta los resultados de la implementación. Por otro lado, la tesis también presenta la arquitectura y los algoritmos para un receptor DVB-S2 dirigido a la implementación en ASIC. Sin embargo, a diferencia del receptor ISDB-T, se introducen sólo los resultados preliminares de implementación en ASIC. Esto se hizo principalmente con el fin de tener una estimación temprana del área del die para demostrar que el proyecto en ASIC es económicamente viable, así como para verificar posibles errores en etapa temprana. Como en el caso de receptor ISDB-T, este receptor se basa fuertemente en el algoritmo CORDIC y fue un prototipado en FPGA. La metodología utilizada para el segundo receptor se deriva de la utilizada para el re[CA] La primera generació de Televisió Digital Terrestre (TDT) ha estat en servici durant més d'una dècada. En 2013, diversos països ja van completar la transició de la radiodifusió de televisió analògica a la digital, i la majoria van ser a Europa. A Amèrica del Sud, després de diversos estudis i assajos, Brasil va adoptar l'estàndard japonés amb algunes innovacions. Japó i Brasil van començar els servicis de Radiodifusió de Televisió Terrestre Digital (DTTB) al desembre de 2003 i al desembre de 2007, respectivament, utilitzant la Radiodifusió Digital amb Servicis Integrats de (ISDB-T), coneguda com a ARIB STD-B31. Al juny de 2005, el Comité de l'Àrea de Tecnologia de la Informació (CATI) del Ministeri de Ciència i Tecnologia i Innovació del Brasil (MCTI) va aprovar la incorporació del programa CI Brasil al Programa Nacional de Microelectrònica (PNM). Els principals objectius de CI Brasil són la qualificació formal dels dissenyadors de circuits integrats, el suport a la creació d'empreses de semiconductors centrades en projectes de circuits integrats dins del Brasil i l'atracció d'empreses de semiconductors centrades en el disseny i desenvolupament de circuits integrats. El treball presentat en esta tesi es va originar en l'impuls únic creat per la combinació del naixement de la televisió digital al Brasil i la creació del programa Brasil CI pel govern brasiler. Sense esta combinació no hauria estat possible realitzar este tipus de projectes a Brasil. Estos projectes han suposat un viatge llarg i costós, tot i que digne científicament i tecnològica, cap a un circuit integrat punter de baixa complexitat per a la TDT brasilera, amb bones perspectives d'economia d'escala perquè a l'inici d'este projecte l'estàndard ISDB-T no va ser adoptat per diversos països, com el DVB-T. Durant el desenvolupament del receptor de ISDB-T proposat en esta tesi, va resultar que, a causa de les dimensions continentals de Brasil, la DTTB no seria suficient per cobrir tot el país amb el senyal de TDT oberta, especialment pel que fa a les localitzacions remotes allunyades de les regions d'alta densitat urbana.. En este moment, l'Institut de Recerca Eldorado i Idea! Sistemes Electrònics van preveure que, en un futur pròxim, no hi hauria a Brasil un sistema de distribució oberta de TDT d'alta definició a través de satèl¿lit. D'acord amb això, l'Institut de Recerca Eldorado va decidir que seria necessari crear un nou ASIC per a la recepció de radiodifusió per satèl¿lit. basat en l'estàndard DVB-S2. En esta tesi s'analitza en detall l'arquitectura i els algorismes proposats per l'execució d'un receptor ISDB-T de Freqüència Intermèdia (FI) de baixa complexitat sobre CMOS de Circuit Integrat d'Aplicacions Específiques (ASIC). L'arquitectura ací proposada es basa molt en l'algorisme de l'Ordinador Digital de Rotació de Coordenades (CORDIC), que és un algorisme simple i eficient adequat per implementacions VLSI. El receptor fa front a les deficiències inherents a la transmissió de canals sense fil i els cristalls del receptor. Esta tesi també analitza la metodologia adoptada i presenta els resultats de l'execució. Es presenta el rendiment del receptor i es compara amb els obtinguts per mitjà de simulacions. D'altra banda, esta tesi també presenta l'arquitectura i els algorismes d'un receptor de DVB-S2 de cara a la seua implementació en ASIC. No obstant això, a diferència del receptor ISDB-T, només s'introdueixen resultats preliminars d'implementació en ASIC. Això es va fer principalment amb la finalitat de tenir una estimació primerenca de la zona de dau per demostrar que el projecte en ASIC és econòmicament viable, així com per verificar possibles errors en l'etapa primerenca. Com en el cas del receptor ISDB-T, este receptor es basa molt en l'algorisme CORDIC i va ser un prototip de FPGA. La metodologia utilitzada per al segon receptor es deriva de la utilitzada per al receptor IRodrigues De Lima, E. (2016). Architecture and algorithms for the implementation of digital wireless receivers in FPGA and ASIC: ISDB-T and DVB-S2 cases [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/61967TESI