Adaptive prediction in digitally controlled buck converter with fast load transient response

An adaptive prediction scheme based on linear extrapolation for digitally controlled voltage-mode buck-type switching converter is presented. A major drawback of conventional digitally controlled switching converters is bandwidth limitation due to the additional phase lag in the digital feedback control loop. By predicting the future error voltage, the ADC sampling time delay is compensated in order to achieve a higher bandwidth even with a modest sampling rate. Both simulation and measurement results show that the output voltage settling time of the digitally controlled buck converter is reduced by as much as 28% with the proposed adaptive prediction. The fastest settling time in response to a 600mA load transient is around 15μs, approaching the transient response of the state-of-the-art analog-based controller.published_or_final_versio

完全自動合成可能な低電力・広入力統計的フラッシュ型A/D変換回路

This work presents a fully synthesizable stochastic flash A/D converter (SFADC), which can operate at the supply voltage of 0.6V with power consumption as low as 1.5mW at the clock frequency of 250MHz. By employing the all-digital comparator, the SFADC can be described with Verilog netlist and synthesized according to a standard digital design flow. Cross-coupled dynamic comparator structure saves the overall power due to remarkable control of dynamic power consumption. In addition, the rail-to-rail characteristic of comparator and the proposed linearity enhancement technique based on SFADC are proposed, allowing us to design a wide input-range stochastic flash ADC.北九州市立大

Low-Power Energy Efficient Circuit Techniques for Small IoT Systems

Although the improvement in circuit speed has been limited in recent years, there has been increased focus on the internet of things (IoT) as technology scaling has decreased circuit size, power usage and cost. This trend has led to the development of many small sensor systems with affordable costs and diverse functions, offering people convenient connection with and control over their surroundings. This dissertation discusses the major challenges and their solutions in realizing small IoT systems, focusing on non-digital blocks, such as power converters and analog sensing blocks, which have difficulty in following the traditional scaling trends of digital circuits. To accommodate the limited energy storage and harvesting capacity of small IoT systems, this dissertation presents an energy harvester and voltage regulators with low quiescent power and good efficiency in ultra-low power ranges. Switched-capacitor-based converters with wide-range energy-efficient voltage-controlled oscillators assisted by power-efficient self-oscillating voltage doublers and new cascaded converter topologies for more conversion ratio configurability achieve efficient power conversion down to several nanowatts. To further improve the power efficiency of these systems, analog circuits essential to most wireless IoT systems are also discussed and improved. A capacitance-to-digital sensor interface and a clocked comparator design are improved by their digital-like implementation and operation in phase and frequency domain. Thanks to the removal of large passive elements and complex analog blocks, both designs achieve excellent area reduction while maintaining state-of-art energy efficiencies. Finally, a technique for removing dynamic voltage and temperature variations is presented as smaller circuits in advanced technologies are more vulnerable to these variations. A 2-D simultaneous feedback control using an on-chip oven control locks the supply voltage and temperature of a small on-chip domain and protects circuits in this locked domain from external voltage and temperature changes, demonstrating 0.0066 V/V and 0.013 °C/°C sensitivities to external changes. Simple digital implementation of the sensors and most parts of the control loops allows robust operation within wide voltage and temperature ranges.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/138743/1/wanyeong_1.pd

Near-Threshold Computing: Past, Present, and Future.

Transistor threshold voltages have stagnated in recent years, deviating from constant-voltage scaling theory and directly limiting supply voltage scaling. To overcome the resulting energy and power dissipation barriers, energy efficiency can be improved through aggressive voltage scaling, and there has been increased interest in operating at near-threshold computing (NTC) supply voltages. In this region sizable energy gains are achieved with moderate performance loss, some of which can be regained through parallelism. This thesis first provides a methodical definition of how near to threshold is "near threshold" and continues with an in-depth examination of NTC across past, present, and future CMOS technologies. By systematically defining near-threshold, the trends and tradeoffs are analyzed, lending insight in how best to design and optimize near-threshold systems. NTC works best for technologies that feature good circuit delay scalability, therefore technologies without strong short-channel effects. Early planar technologies (prior to 90nm or so) featured good circuit scalability (8x energy gains), but lacked area in which to add cores for parallelization. Recent planar nodes (32nm – 20nm) feature more area for cores but suffer from poor delay scalability, and so are not well-suited for NTC (4x energy gains). The switch to FinFET CMOS technology allows for a return to strong voltage scalability (8x gain), reversing trends seen in planar technologies, while dark silicon has created an opportunity to add cores for parallelization. Improved FinFET voltage scalability even allows for latency reduction of a single task, as long as the task is sufficiently parallelizable (< 10% serial code). Finally, we will look at a technique for fast voltage boosting, called Shortstop, in which a core's operating voltage is raised in 10s of cycles. Shortstop can be used to quickly respond to single-threaded performance demands of a near-threshold system by leveraging the innate parasitic inductance of a dedicated dirty supply rail, further improving energy efficiency. The technique is demonstrated in a wirebond implementation and is able to boost a core up to 1.8x faster than a header-based approach, while reducing supply droop by 2-7x. An improved flip-chip architecture is also proposed.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/113600/1/npfet_1.pd

High Performance Optical Transmitter Ffr Next Generation Supercomputing and Data Communication

High speed optical interconnects consuming low power at affordable prices are always a major area of research focus. For the backbone network infrastructure, the need for more bandwidth driven by streaming video and other data intensive applications such as cloud computing has been steadily pushing the link speed to the 40Gb/s and 100Gb/s domain. However, high power consumption, low link density and high cost seriously prevent traditional optical transceiver from being the next generation of optical link technology. For short reach communications, such as interconnects in supercomputers, the issues related to the existing electrical links become a major bottleneck for the next generation of High Performance Computing (HPC). Both applications are seeking for an innovative solution of optical links to tackle those current issues. In order to target the next generation of supercomputers and data communication, we propose to develop a high performance optical transmitter by utilizing CISCO Systems®\u27s proprietary CMOS photonic technology. The research seeks to achieve the following outcomes: 1. Reduction of power consumption due to optical interconnects to less than 5pJ/bit without the need for Ring Resonators or DWDM and less than 300fJ/bit for short distance data bus applications. 2. Enable the increase in performance (computing speed) from Peta-Flop to Exa-Flops without the proportional increase in cost or power consumption that would be prohibitive to next generation system architectures by means of increasing the maximum data transmission rate over a single fiber. 3. Explore advanced modulation schemes such as PAM-16 (Pulse-Amplitude-Modulation with 16 levels) to increase the spectrum efficiency while keeping the same or less power figure. This research will focus on the improvement of both the electrical IC and optical IC for the optical transmitter. An accurate circuit model of the optical device is created to speed up the performance optimization and enable co-simulation of electrical driver. Circuit architectures are chosen to minimize the power consumption without sacrificing the speed and noise immunity. As a result, a silicon photonic based optical transmitter employing 1V supply, featuring 20Gb/s data rate is fabricated. The system consists of an electrical driver in 40nm CMOS and an optical MZI modulator with an RF length of less than 0.5mm in 0.13&mu m SOI CMOS. Two modulation schemes are successfully demonstrated: On-Off Keying (OOK) and Pulse-Amplitude-Modulation-N (PAM-N N=4, 16). Both versions demonstrate signal integrity, interface density, and scalability that fit into the next generation data communication and exa-scale computing. Modulation power at 20Gb/s data rate for OOK and PAM-16 of 4pJ/bit and 0.25pJ/bit are achieved for the first time of an MZI type optical modulator, respectively

DIGITALLY ASSISTED TECHNIQUES FOR NYQUIST RATE ANALOG-to-DIGITAL CONVERTERS

With the advance of technology and rapid growth of digital systems, low power high speed analog-to-digital converters with great accuracy are in demand. To achieve high effective number of bits Analog-to-Digital Converter(ADC) calibration as a time consuming process is a potential bottleneck for designs. This dissertation presentsa fully digital background calibration algorithm for a 7-bit redundant flash ADC using split structure and look-up table based correction. Redundant comparators are used in the flash ADC design of this work in order to tolerate large offset voltages while minimizing signal input capacitance. The split ADC structure helps by eliminating the unknown input signal from the calibration path. The flash ADC has been designed in 180nm IBM CMOS technology and fabricated through MOSIS. This work was supported by Analog Devices, Wilmington,MA. While much research on ADC design has concentrated on increasing resolution and sample rate, there are many applications (e.g. biomedical devices and sensor networks) that do not require high performance but do require low power energy efficient ADCs. This dissertation also explores on design of a low quiescent current 100kSps Successive Approximation (SAR) ADC that has been used as an error detection ADC for an automotive application in 350nm CD (CMOS-DMOS) technology. This work was supported by ON Semiconductor Corp, East Greenwich,RI

Design of PVT Tolerant Inverter Based Circuits for Low Supply Voltages

University of Minnesota Ph.D. dissertation. June 2015. Major: Electrical Engineering. Advisor: Ramesh Harjani. 1 computer file (PDF); xiv, 187 pages.Rapid advances in the field of integrated circuit design has been advantageous from the point of view of cost and miniaturization. Although technology scaling is advantageous to digital circuits in terms of increased speed and lower power, analog circuits strongly suffer from this trend. This is becoming a crucial bottle neck in the realization of a system on chip in scaled technology merging high-density digital parts, with high performance analog interfaces. This is because scaled technologies reduce the output impedance (gain) and supply voltage which limits the dynamic range (output swing). One way to mitigate the power supply restrictions is to move to current mode circuit circuit design rather than voltage mode designs. This thesis focuses on designing Process Voltage and Temperature (PVT) tolerant base band circuits at lower supply voltages and in lower technologies. Inverter amplifiers are known to have better transconductance efficiency, better noise and linearity performance. But inverters are prone to PVT variations and has poor CMRR and PSRR. To circumvent the problem, we have proposed various biasing schemes for inverter like semi constant current biasing, constant current biasing and constant gm biasing. Each biasing technique has its own advantages, like semi constant current biasing allows to select different PMOS and NMOS current. This feature allows for higher inherent inverter linearity. Similarly constant current and constant gm biasing allows for reduced PVT sensitivity. The inverter based OTA achieves a measured THD of -90.6 dB, SNR of 78.7 dB, CMRR 97dB, PSRR 61 dB wile operating from a nominal power of 0.9V and at output swing of 0.9V{pp,diff} in TSMC 40nm general purpose process. Further the measured third harmonic distortion varies approximately by 11.5dB with 120C variation in temperature and 9dB with a 18% variation in supply voltage. The linearity can be increased by increasing the loop gain and bandwidth in a negative feedback circuit or by increasing the over drive voltage in open loop architectures. However both these techniques increases the noise contribution of the circuit. There exist a trade off between noise and linearity in analog circuits. To circumvent this problem, we have introduced nonlinear cancellation techniques and noise filtering techniques. An analog-to-digital converter (ADC) driver which is capable of amplifying the continuous time signal with a gain of 8 and sample onto the input capacitor(1pF) of 1 10 bit successive approximation register (SAR) ADC is designed in TSMC 65nm general purpose process. This exploits the non linearity cancellation in current mirror and also allows for higher bandwidth operation by decoupling closed loop gain from the negative feedback loop. The noise from the out of band is filtered before sampling leading to low noise operation. The measured design operates at 100MS/s and has an OIP_3 of 40dBm at the nyquist rate, noise power spectral density of 17nV/sqrt{Hz} and inter modulation distortion of 65dB. The intermodulation distortion variation across 10 chips is 6dB and 4dB across a temperature variation of 120C. Non linearity cancellation is exploited in designing two filters, an anti alias filter and a continuously tunable channel select filter. Traditional active RC filters are based on cascade of integrators. These create multiple low impedance nodes in the circuit which results in a higher noise. We propose a real low pass filter based filter architecture rather than traditional integrator based approach. Further the entire filtering operation takes place in current domain to circumvent the power supply limitations. This also facilitates the use of tunable non linear metal oxide semiconductor capacitor (MOSCAP) as filter capacitors. We introduce techniques of self compensation to use the filter resistor and capacitor as compensation capacitor for lower power. The anti alias filter designed for 50MHz bandwidth is fabricated in IBM 65nm process achieves an IIP3 of 33dBm, while consuming 1.56mW from 1.2 V supply. The channel select filter is tunable from 34MHz to 314MHz and is fabricated in TSMC 65nm general purpose process. This filter achieves an OIP3 of 25.24 dBm at the maximum frequency while drawing 4.2mA from 1.1V supply. The measured intermodulation distortion varies by 5dB across 120C variation in temperature and 6.5dB across a 200mV variation in power supply. Further this filter presents a high impedance node at the input and a low impedance node at the output easing system integration. SAR ADCs are becoming popular at lower technologies as they are based on device switching rather than amplifying circuits. But recent SAR ADCs that have good energy efficiency have had relatively large input capacitance increasing the driver power. We present a 2X time interleaved (TI) SAR ADC which has the lowest input capacitance of 133fF in literature. The sampling capacitor is separated from the capacitive digital to analog converter (DAC) array by performing the input and DAC reference subtraction in the current domain rather than as done traditionally in charge domain. The proposed ADC is fabricated in TSMC's 65nm general purpose process and occupies an area of 0.0338 mm^2. The measured ADC spurious free dynamic range (SFDR) is 57dB and the measured effective number of bits (ENOB) at nyquist rate is 7.55 bit while using 1.55mW power from 1 V supply. A sub 1V reference circuit is proposed, that exploits the complementary to absolute temperature (CTAT) and proportional to absolute temperature (PTAT) voltages in the beta multiplier circuit to attain a stable voltage with temperature and power supply. A one-time calibration is integrated in the architecture to get a good performance over process. Chopper stabilization is employed to reduce the flicker noise of the reference circuit. The prototype was simulated in TSMC 65nm process and we obtain the nominal output of 236mW, while consuming 0.7mW from power supply. Simulations show a temperature coefficient of 18 ppmC from -40 to 100C and with a power supply ranging from 0.8 to 2V