Energy-Efficient Digital Circuit Design using Threshold Logic Gates

abstract: Improving energy efficiency has always been the prime objective of the custom and automated digital circuit design techniques. As a result, a multitude of methods to reduce power without sacrificing performance have been proposed. However, as the field of design automation has matured over the last few decades, there have been no new automated design techniques, that can provide considerable improvements in circuit power, leakage and area. Although emerging nano-devices are expected to replace the existing MOSFET devices, they are far from being as mature as semiconductor devices and their full potential and promises are many years away from being practical. The research described in this dissertation consists of four main parts. First is a new circuit architecture of a differential threshold logic flipflop called PNAND. The PNAND gate is an edge-triggered multi-input sequential cell whose next state function is a threshold function of its inputs. Second a new approach, called hybridization, that replaces flipflops and parts of their logic cones with PNAND cells is described. The resulting \hybrid circuit, which consists of conventional logic cells and PNANDs, is shown to have significantly less power consumption, smaller area, less standby power and less power variation. Third, a new architecture of a field programmable array, called field programmable threshold logic array (FPTLA), in which the standard lookup table (LUT) is replaced by a PNAND is described. The FPTLA is shown to have as much as 50% lower energy-delay product compared to conventional FPGA using well known FPGA modeling tool called VPR. Fourth, a novel clock skewing technique that makes use of the completion detection feature of the differential mode flipflops is described. This clock skewing method improves the area and power of the ASIC circuits by increasing slack on timing paths. An additional advantage of this method is the elimination of hold time violation on given short paths. Several circuit design methodologies such as retiming and asynchronous circuit design can use the proposed threshold logic gate effectively. Therefore, the use of threshold logic flipflops in conventional design methodologies opens new avenues of research towards more energy-efficient circuits.Dissertation/ThesisDoctoral Dissertation Computer Science 201

Exploiting Adaptive Techniques to Improve Processor Energy Efficiency

Rapid device-miniaturization keeps on inducing challenges in building energy efficient microprocessors. As the size of the transistors continuously decreasing, more uncertainties emerge in their operations. On the other hand, integrating more and more transistors on a single chip accentuates the need to lower its supply-voltage. This dissertation investigates one of the primary device uncertainties - timing error, in microprocessor performance bottleneck in NTC era. Then it proposes various innovative techniques to exploit these opportunities to maintain processor energy efficiency, in the context of emerging challenges. Evaluated with the cross-layer methodology, the proposed approaches achieve substantial improvements in processor energy efficiency, compared to other start-of-art techniques

Modeling and Analysis of Noise and Interconnects for On-Chip Communication Link Design

This thesis considers modeling and analysis of noise and interconnects in onchip communication. Besides transistor count and speed, the capabilities of a modern design are often limited by on-chip communication links. These links typically consist of multiple interconnects that run parallel to each other for long distances between functional or memory blocks. Due to the scaling of technology, the interconnects have considerable electrical parasitics that affect their performance, power dissipation and signal integrity. Furthermore, because of electromagnetic coupling, the interconnects in the link need to be considered as an interacting group instead of as isolated signal paths. There is a need for accurate and computationally effective models in the early stages of the chip design process to assess or optimize issues affecting these interconnects. For this purpose, a set of analytical models is developed for on-chip data links in this thesis. First, a model is proposed for modeling crosstalk and intersymbol interference. The model takes into account the effects of inductance, initial states and bit sequences. Intersymbol interference is shown to affect crosstalk voltage and propagation delay depending on bus throughput and the amount of inductance. Next, a model is proposed for the switching current of a coupled bus. The model is combined with an existing model to evaluate power supply noise. The model is then applied to reduce both functional crosstalk and power supply noise caused by a bus as a trade-off with time. The proposed reduction method is shown to be effective in reducing long-range crosstalk noise. The effects of process variation on encoded signaling are then modeled. In encoded signaling, the input signals to a bus are encoded using additional signaling circuitry. The proposed model includes variation in both the signaling circuitry and in the wires to calculate the total delay variation of a bus. The model is applied to study level-encoded dual-rail and 1-of-4 signaling. In addition to regular voltage-mode and encoded voltage-mode signaling, current-mode signaling is a promising technique for global communication. A model for energy dissipation in RLC current-mode signaling is proposed in the thesis. The energy is derived separately for the driver, wire and receiver termination.Siirretty Doriast

Power Reductions with Energy Recovery Using Resonant Topologies

The problem of power densities in system-on-chips (SoCs) and processors has become more exacerbated recently, resulting in high cooling costs and reliability issues. One of the largest components of power consumption is the low skew clock distribution network (CDN), driving large load capacitance. This can consume as much as 70% of the total dynamic power that is lost as heat, needing elaborate sensing and cooling mechanisms. To mitigate this, resonant clocking has been utilized in several applications over the past decade. An improved energy recovering reconfigurable generalized series resonance (GSR) solution with all the critical support circuitry is developed in this work. This LC resonant clock driver is shown to save about 50% driver power (\u3e40% overall), on a 22nm process node and has 50% less skew than a non-resonant driver at 2GHz. It can operate down to 0.2GHz to support other energy savings techniques like dynamic voltage and frequency scaling (DVFS). As an example, GSR can be configured for the simpler pulse series resonance (PSR) operation to enable further power saving for double data rate (DDR) applications, by using de-skewing latches instead of flip-flop banks. A PSR based subsystem for 40% savings in clocking power with 40% driver active area reduction xii is demonstrated. This new resonant driver generates tracking pulses at each transition of clock for dual edge operation across DVFS. PSR clocking is designed to drive explicit-pulsed latches with negative setup time. Simulations using 45nm IBM/PTM device and interconnect technology models, clocking 1024 flip-flops show the reductions, compared to non-resonant clocking. DVFS range from 2GHz/1.3V to 200MHz/0.5V is obtained. The PSR frequency is set \u3e3× the clock rate, needing only 1/10th the inductance of prior-art LC resonance schemes. The skew reductions are achieved without needing to increase the interconnect widths owing to negative set-up times. Applications in data circuits are shown as well with a 90nm example. Parallel resonant and split-driver non-resonant configurations as well are derived from GSR. Tradeoffs in timing performance versus power, based on theoretical analysis, are compared for the first time and verified. This enables synthesis of an optimal topology for a given application from the GSR

Models predicting the performance of IC component or PCB channel during electromagnetic interference

This dissertation is composed of three papers, which cover the prediction of the characteristics of jitter due to crosstalk and due to simultaneous switching noise, and covers susceptibility of delay locked loop (DLL) to electromagnetic interference. In the first paper, an improved tail-fit de-convolution method is proposed for characterizing the impact of deterministic jitter in the presence of random jitter. A Wiener filter de-convolution method is also presented for extracting the characteristics of crosstalk induced jitter from measurements of total jitter made when the crosstalk sources were and were not present. The proposed techniques are shown to work well both in simulations and in measurements of a high-speed link. In the second paper, methods are developed to predict the statistical distribution of timing jitter due to dynamic currents drawn by an integrated circuit (IC) and the resulting power supply noise on the PCB. Distribution of dynamic currents is found through vectorless methods. Results demonstrate the approach can rapidly determine the average and standard deviation of the power supply noise voltage and the peak jitter within 5~15% error, which is more than sufficient for predicting the performance impact on integrated circuits. In the third paper, a model is developed to predict the susceptibility of a DLL to electromagnetic noise on the power supply. With the proposed analytical noise transfer function, peak to peak jitter and cycle to cycle jitter at the DLL output can be estimated, which can be use to predict when soft failures will occur and to better understand how to fix these failures. Simulation and measurement results demonstrate the accuracy of the DLL delay model. --Abstract, page iv

Low-Power Embedded Design Solutions and Low-Latency On-Chip Interconnect Architecture for System-On-Chip Design

This dissertation presents three design solutions to support several key system-on-chip (SoC) issues to achieve low-power and high performance. These are: 1) joint source and channel decoding (JSCD) schemes for low-power SoCs used in portable multimedia systems, 2) efficient on-chip interconnect architecture for massive multimedia data streaming on multiprocessor SoCs (MPSoCs), and 3) data processing architecture for low-power SoCs in distributed sensor network (DSS) systems and its implementation. The first part includes a low-power embedded low density parity check code (LDPC) - H.264 joint decoding architecture to lower the baseband energy consumption of a channel decoder using joint source decoding and dynamic voltage and frequency scaling (DVFS). A low-power multiple-input multiple-output (MIMO) and H.264 video joint detector/decoder design that minimizes energy for portable, wireless embedded systems is also designed. In the second part, a link-level quality of service (QoS) scheme using unequal error protection (UEP) for low-power network-on-chip (NoC) and low latency on-chip network designs for MPSoCs is proposed. This part contains WaveSync, a low-latency focused network-on-chip architecture for globally-asynchronous locally-synchronous (GALS) designs and a simultaneous dual-path routing (SDPR) scheme utilizing path diversity present in typical mesh topology network-on-chips. SDPR is akin to having a higher link width but without the significant hardware overhead associated with simple bus width scaling. The last part shows data processing unit designs for embedded SoCs. We propose a data processing and control logic design for a new radiation detection sensor system generating data at or above Peta-bits-per-second level. Implementation results show that the intended clock rate is achieved within the power target of less than 200mW. We also present a digital signal processing (DSP) accelerator supporting configurable MAC, FFT, FIR, and 3-D cross product operations for embedded SoCs. It consumes 12.35mW along with 0.167mm2 area at 333MHz

Synergistic Timing Speculation for Multi-Threaded Programs

Timing speculation is a promising approach to increase the processor performance and energy efficiency. Under timing speculation, an integrated circuit is allowed to operate at a speed faster than its slowest path|the critical path. It is based on the empirical observation, which is presented later in the thesis, that these critical path delays are rarely manifested during the program execution. Consequently, as long as the processor is equipped with an error detection and recovery mechanism, its performance can be increased and/or energy consumption reduced beyond that achievable by any other conventional operation. While many past works have dealt with timing speculation within a single core, in this work, a new direction is being uncovered | timing speculation for a multi-core processor executing a parallel, multi-threaded application. Through a rigorous cross-layered circuit architectural analysis, it is observed that during the execution of a multi-threaded program, there is a significant variation in circuit delay characteristics across different threads. Synergistic Timing Speculation (SynTS) is proposed to exploit this variation (heterogeneity) in path sensitization delays, to jointly optimize the energy and execution time of the many-core processor. In particular, SynTS uses a sampling based online error probability estimation technique, coupled with a polynomial time algorithm, to optimally determine the voltage, frequency and the amount of timing speculation for each thread. The experimental analysis is presented for three pipe stages, namely, Decode, SimpleALU and ComplexALU, with a reduction in Energy Delay Product by up to 26%, 25% and 7.5% respectively, compared to existing per-core timing speculation scheme. The analysis also embeds a case study for a General Purpose Graphics Processing Unit

Generating and auto-tuning parallel stencil codes

In this thesis, we present a software framework, Patus, which generates high performance stencil codes for different types of hardware platforms, including current multicore CPU and graphics processing unit architectures. The ultimate goals of the framework are productivity, portability (of both the code and performance), and achieving a high performance on the target platform. A stencil computation updates every grid point in a structured grid based on the values of its neighboring points. This class of computations occurs frequently in scientific and general purpose computing (e.g., in partial differential equation solvers or in image processing), justifying the focus on this kind of computation. The proposed key ingredients to achieve the goals of productivity, portability, and performance are domain specific languages (DSLs) and the auto-tuning methodology. The Patus stencil specification DSL allows the programmer to express a stencil computation in a concise way independently of hardware architecture-specific details. Thus, it increases the programmer productivity by disburdening her or him of low level programming model issues and of manually applying hardware platform-specific code optimization techniques. The use of domain specific languages also implies code reusability: once implemented, the same stencil specification can be reused on different hardware platforms, i.e., the specification code is portable across hardware architectures. Constructing the language to be geared towards a special purpose makes it amenable to more aggressive optimizations and therefore to potentially higher performance. Auto-tuning provides performance and performance portability by automated adaptation of implementation-specific parameters to the characteristics of the hardware on which the code will run. By automating the process of parameter tuning — which essentially amounts to solving an integer programming problem in which the objective function is the number representing the code's performance as a function of the parameter configuration, — the system can also be used more productively than if the programmer had to fine-tune the code manually. We show performance results for a variety of stencils, for which Patus was used to generate the corresponding implementations. The selection includes stencils taken from two real-world applications: a simulation of the temperature within the human body during hyperthermia cancer treatment and a seismic application. These examples demonstrate the framework's flexibility and ability to produce high performance code

Archiving the Relaxed Consistency Web

The historical, cultural, and intellectual importance of archiving the web has been widely recognized. Today, all countries with high Internet penetration rate have established high-profile archiving initiatives to crawl and archive the fast-disappearing web content for long-term use. As web technologies evolve, established web archiving techniques face challenges. This paper focuses on the potential impact of the relaxed consistency web design on crawler driven web archiving. Relaxed consistent websites may disseminate, albeit ephemerally, inaccurate and even contradictory information. If captured and preserved in the web archives as historical records, such information will degrade the overall archival quality. To assess the extent of such quality degradation, we build a simplified feed-following application and simulate its operation with synthetic workloads. The results indicate that a non-trivial portion of a relaxed consistency web archive may contain observable inconsistency, and the inconsistency window may extend significantly longer than that observed at the data store. We discuss the nature of such quality degradation and propose a few possible remedies.Comment: 10 pages, 6 figures, CIKM 201

Process-induced skew reduction in nominal zero-skew clock trees

Abstract — This work develops an analytic framework for clock tree analysis considering process variations that is shown to correspond well with Monte Carlo results. The analysis frame-work is used in a new algorithm that constructs deterministic nominal zero-skew clock trees that have reduced sensitivity to process variation. The new algorithm uses a sampling approach to perform route embedding during a bottom-up merging phase, but does not select the best embedding until the top-down phase. This results in clock trees that exhibit a mean skew reduction of 32.4 % on average and a standard deviation reduction of 40.7 % as verified by Monte Carlo. The average increase in total clock tree capacitance is less than 0.02%. I