Limiting Performance of Conventional and Widely Linear DFT-precoded-OFDM Receivers in Wideband Frequency Selective Channels

This paper describes the limiting behavior of linear and decision feedback equalizers (DFEs) in single/multiple antenna systems employing real/complex-valued modulation alphabets. The wideband frequency selective channel is modeled using a Rayleigh fading channel model with infinite number of time domain channel taps. Using this model, we show that the considered equalizers offer a fixed post signal-to-noise-ratio (post-SNR) at the equalizer output that is close to the matched filter bound (MFB). General expressions for the post-SNR are obtained for zero-forcing (ZF) based conventional receivers as well as for the case of receivers employing widely linear (WL) processing. Simulation is used to study the bit error rate (BER) performance of both MMSE and ZF based receivers. Results show that the considered receivers advantageously exploit the rich frequency selective channel to mitigate both fading and inter-symbol-interference (ISI) while offering a performance comparable to the MFB

Dual-Polarization OFDM-OQAM Wireless Communication System

In this paper we describe the overall idea and results of a recently proposed radio access technique based on filter bank multicarrier (FBMC) communication system using two orthogonal polarizations: dual-polarization FBMC (DP-FBMC). Using this system we can alleviate the intrinsic interference problem in FBMC systems. This enables use of all the multicarrier techniques used in cyclic-prefix orthogonal frequency-division multiplexing (CP-OFDM) systems for channel equalization, multiple-input/multiple-output (MIMO) processing, etc., without using the extra processing required for conventional FBMC. DP-FBMC also provides other interesting advantages over CP-OFDM and FBMC such as more robustness in multipath fading channels, and more robustness to receiver carrier frequency offset (CFO) and timing offset (TO). For DP-FBMC we propose three different structures based on different multiplexing techniques in time, frequency, and polarization. We will show that one of these structures has exactly the same system complexity and equipment as conventional FBMC. In our simulation results DP-FBMC has better bit error ratio (BER) performance in dispersive channels. Based on these results, DP-FBMC has potential as a promising candidate for future wireless communication systems.Comment: 1.This paper is accepted to be published in IEEE Vehicular Technology Conference (VTC) FALL 2018. 2.In this new submitted version authors have revised the paper based on the VTC FALL reviewers comments. Therefore some typos have fixed and some results have change

A Generalized Framework on Beamformer Design and CSI Acquisition for Single-Carrier Massive MIMO Systems in Millimeter Wave Channels

In this paper, we establish a general framework on the reduced dimensional channel state information (CSI) estimation and pre-beamformer design for frequency-selective massive multiple-input multiple-output MIMO systems employing single-carrier (SC) modulation in time division duplex (TDD) mode by exploiting the joint angle-delay domain channel sparsity in millimeter (mm) wave frequencies. First, based on a generic subspace projection taking the joint angle-delay power profile and user-grouping into account, the reduced rank minimum mean square error (RR-MMSE) instantaneous CSI estimator is derived for spatially correlated wideband MIMO channels. Second, the statistical pre-beamformer design is considered for frequency-selective SC massive MIMO channels. We examine the dimension reduction problem and subspace (beamspace) construction on which the RR-MMSE estimation can be realized as accurately as possible. Finally, a spatio-temporal domain correlator type reduced rank channel estimator, as an approximation of the RR-MMSE estimate, is obtained by carrying out least square (LS) estimation in a proper reduced dimensional beamspace. It is observed that the proposed techniques show remarkable robustness to the pilot interference (or contamination) with a significant reduction in pilot overhead

Wireless industrial monitoring and control networks: the journey so far and the road ahead

While traditional wired communication technologies have played a crucial role in industrial monitoring and control networks over the past few decades, they are increasingly proving to be inadequate to meet the highly dynamic and stringent demands of today’s industrial applications, primarily due to the very rigid nature of wired infrastructures. Wireless technology, however, through its increased pervasiveness, has the potential to revolutionize the industry, not only by mitigating the problems faced by wired solutions, but also by introducing a completely new class of applications. While present day wireless technologies made some preliminary inroads in the monitoring domain, they still have severe limitations especially when real-time, reliable distributed control operations are concerned. This article provides the reader with an overview of existing wireless technologies commonly used in the monitoring and control industry. It highlights the pros and cons of each technology and assesses the degree to which each technology is able to meet the stringent demands of industrial monitoring and control networks. Additionally, it summarizes mechanisms proposed by academia, especially serving critical applications by addressing the real-time and reliability requirements of industrial process automation. The article also describes certain key research problems from the physical layer communication for sensor networks and the wireless networking perspective that have yet to be addressed to allow the successful use of wireless technologies in industrial monitoring and control networks

Characterization and Mitigation of Hyper-Rayleigh Fading

Due to the unprecedented spatial and temporal resolution they offer, wireless sensor networks are considered an enabling technology for the distributed monitoring of industrial, military, and natural environments. As these systems migrate into vastly different and novel applications, new constraints are discovered that affect network reliability and utility. For example, wireless sensors are typically statically deployed and, unlike mobile systems, cannot move to a new location for better radio reception. As a result, the signal fades caused by non-optimal environmental conditions can increase the outage probability of the system, potentially rendering the network unreliable and ineffectual. Stochastic models that quantify link reliability and the effectiveness of diversity methods are often employed to understand the impact of such fading. However, the performance of these models applied to wireless sensor networks is entirely dependent on the appropriateness of the model with respect to the environment. This work first presents an empirical study of the propagation environment for a wingless, rotary aircraft, showing that the wireless environment within exhibits frequency-selective fading much more severe than predicted by current worst-case models (i.e., Rayleigh). An analysis is then given of the effectiveness of several diversity methods operating within such environments (referred to as hyper-Rayleigh). These fade mitigation techniques are simple enough to be employed for use with low-complexity wireless sensor hardware, and include spatial diversity, polar diversity, two-element passive combining, and two-element phased combining. Two-element phased combining is further developed by examining the effect that smaller element spacing has on diversity gain. A demonstration of a wireles

Full-duplex wireless communications: challenges, solutions and future research directions

The family of conventional half-duplex (HD) wireless systems relied on transmitting and receiving in different time-slots or frequency sub-bands. Hence the wireless research community aspires to conceive full-duplex (FD) operation for supporting concurrent transmission and reception in a single time/frequency channel, which would improve the attainable spectral efficiency by a factor of two. The main challenge encountered in implementing an FD wireless device is the large power difference between the self-interference (SI) imposed by the device’s own transmissions and the signal of interest received from a remote source. In this survey, we present a comprehensive list of the potential FD techniques and highlight their pros and cons. We classify the SI cancellation techniques into three categories, namely passive suppression, analog cancellation and digital cancellation, with the advantages and disadvantages of each technique compared. Specifically, we analyse the main impairments (e.g. phase noise, power amplifier nonlinearity as well as in-phase and quadrature-phase (I/Q) imbalance, etc.) that degrading the SI cancellation. We then discuss the FD based Media Access Control (MAC)-layer protocol design for the sake of addressing some of the critical issues, such as the problem of hidden terminals, the resultant end-to-end delay and the high packet loss ratio (PLR) due to network congestion. After elaborating on a variety of physical/MAC-layer techniques, we discuss potential solutions conceived for meeting the challenges imposed by the aforementioned techniques. Furthermore, we also discuss a range of critical issues related to the implementation, performance enhancement and optimization of FD systems, including important topics such as hybrid FD/HD scheme, optimal relay selection and optimal power allocation, etc. Finally, a variety of new directions and open problems associated with FD technology are pointed out. Our hope is that this treatise will stimulate future research efforts in the emerging field of FD communication

Multi-Polarized Channel Characterization

Machine-to-machine (M2M) communication is becoming an important aspect of warehouse management, remote control, robotics, traffic control, supply chain management, fleet management and telemedicine. M2M is expected to become a significant portion of the Industrial Internet and, more broadly, the Internet of Things (IoT). The environments in which M2M systems are expected to operate may be challenging in terms of radio wave propagation due to their cluttered, multipath nature, which can cause deep signal fades and signal depolarization. Polarization diversity in two dimensions is a well-known technique to mitigate such fades. But in the presence of reflectors and retarders where multipath components arrive from any direction, we find the detrimental effects to be three-dimensional and thus consider herein mitigation approaches that are also 3D. The objectives of this dissertation are three. First, to provide a theoretical framework for depolarization in three dimensions. Second, to prepare a tripolar antenna design that meets cost, power consumption, and simplicity requirements of M2M applications and that can mitigate the expected channel effects. Finally, to develop new channel models in three dimensional space for wireless systems. Accordingly, this dissertation presents a complete description of 3D electromagnetic fields, in terms of their polarization characteristics and confirms the advantage of employing tripolar antennas in multipath conditions. Furthermore, the experimental results illustrate that highly variable depolarization occurs across all three spatial dimensions and is dependent on small changes in frequency and space. Motivated by these empirical results, we worked with a collaborating institution to develop a three-dimensional tripolar antenna that can be integrated with a commercially available wireless sensor. This dissertation presents the testing results that show that this design significantly improves channels over traditional 2D approaches. The implications of tripolar antenna integration on M2M systems include reduction in energy use, longer wireless communication link distances, and/or greater link reliability. Similar results are shown for a planar antenna design that enables four different polarization configurations. Finally, the work presents a novel three-dimensional geometry-based stochastic channel model that builds the channel as a sum of shell-like sub-regions, where each sub-region consists of groups of multipath components. The model is validated with empirical data to show the approach may be used for system analyses in indoor environments

Detect-and-forward relaying aided cooperative spatial modulation for wireless networks

A novel detect-and-forward (DeF) relaying aided cooperative SM scheme is proposed, which is capable of striking a flexible tradeoff in terms of the achievable bit error ratio (BER), complexity and unequal error protection (UEP). More specifically, SM is invoked at the source node (SN) and the information bit stream is divided into two different sets: the antenna index-bits (AI-bits) as well as the amplitude and phase modulation-bits (APM-bits). By exploiting the different importance of the AI-bits and the APM-bits in SM detection, we propose three low-complexity, yet powerful relay protocols, namely the partial, the hybrid and the hierarchical modulation (HM) based DeF relaying schemes. These schemes determine the most appropriate number of bits to be re-modulated by carefully considering their potential benefits and then assigning a specific modulation scheme for relaying the message. As a further benefit, the employment of multiple radio frequency (RF) chains and the requirement of tight inter-relay synchronization (IRS) can be avoided. Moreover, by exploiting the benefits of our low-complexity relaying protocols and our inter-element interference (IEI) model, a low-complexity maximum-likelihood (ML) detector is proposed for jointly detecting the signal received both via the source-destination (SD) and relay-destination (RD) links. Additionally, an upper bound of the BER is derived for our DeF-SM scheme. Our numerical results show that the bound is asymptotically tight in the high-SNR region and the proposed schemes provide beneficial system performance improvements compared to the conventional MIMO schemes in an identical cooperative scenario.<br/