718 research outputs found
Design of CMOS integrated frequency synthesizers for ultra-wideband wireless communications systems
Ultra¬wide band (UWB) system is a breakthrough in wireless communication, as it provides data rate one order higher than existing ones. This dissertation focuses on the design of CMOS integrated frequency synthesizer and its building blocks used in UWB system.
A mixer¬based frequency synthesizer architecture is proposed to satisfy the agile frequency hopping requirement, which is no more than 9.5 ns, three orders faster than conventional phase¬locked loop (PLL)¬based synthesizers. Harmonic cancela¬tion technique is extended and applied to suppress the undesired harmonic mixing components. Simulation shows that sidebands at 2.4 GHz and 5 GHz are below 36 dBc from carrier. The frequency synthesizer contains a novel quadrature VCO based on the capacitive source degeneration structure. The QVCO tackles the jeopardous ambiguity of the oscillation frequency in conventional QVCOs. Measurement shows that the 5¬GHz CSD¬QVCO in 0.18 µm CMOS technology draws 5.2 mA current from a 1.2 V power supply. Its phase noise is ¬120 dBc at 3 MHz offset. Compared with existing phase shift LC QVCOs, the proposed CSD¬QVCO presents better phase noise and power efficiency.
Finally, a novel injection locking frequency divider (ILFD) is presented. Im¬plemented with three stages in 0.18 µm CMOS technology, the ILFD draws 3¬mA current from a 1.8¬V power supply. It achieves multiple large division ratios as 6, 12, and 18 with all locking ranges greater than 1.7 GHz and injection frequency up to 11 GHz. Compared with other published ILFDs, the proposed ILFD achieves the largest division ratio with satisfactory locking range
Quadrature Phase-Domain ADPLL with Integrated On-line Amplitude Locked Loop Calibration for 5G Multi-band Applications
5th generation wireless systems (5G) have expanded frequency band coverage with the low-band 5G and mid-band 5G frequencies spanning 600 MHz to 4 GHz spectrum. This dissertation focuses on a microelectronic implementation of CMOS 65 nm design of an All-Digital Phase Lock Loop (ADPLL), which is a critical component for advanced 5G wireless transceivers. The ADPLL is designed to operate in the frequency bands of 600MHz-930MHz, 2.4GHz-2.8GHz and 3.4GHz-4.2GHz. Unique ADPLL sub-components include: 1) Digital Phase Frequency Detector, 2) Digital Loop Filter, 3) Channel Bank Select Circuit, and 4) Digital Control Oscillator. Integrated with the ADPLL is a 90-degree active RC-CR phase shifter with on-line amplitude locked loop (ALL) calibration to facilitate enhanced image rejection while mitigating the effects of fabrication process variations and component mismatch. A unique high-sensitivity high-speed dynamic voltage comparator is included as a key component of the active phase shifter/ALL calibration subsystem. 65nm CMOS technology circuit designs are included for the ADPLL and active phase shifter with simulation performance assessments. Phase noise results for 1 MHz offset with carrier frequencies of 600MHz, 2.4GHz, and 3.8GHz are -130, -122, and -116 dBc/Hz, respectively. Monte Carlo simulations to account for process variations/component mismatch show that the active phase shifter with ALL calibration maintains accurate quadrature phase outputs when operating within the frequency bands 600MHz-930MHz, 2.4GHz-2.8GHz and 3.4GHz-4.2GHz
A 2.4GHz fast-switching integer-N frequency synthesizer
The adaptive bandwidth technique is commonly used to implement fast switching in low-spurious frequency synthesizers. In this technique the high loop bandwidth used during the switching mode has to be restored once switching is complete. The process of restoring the bandwidth adds to the total switching time because of the glitches on the VCO control voltage arising from the perturbation caused in the loop. Often in applications demanding ultra fast switching times and tight error tolerances, the additional settling time due to these secondary glitches can be a significant fraction of the total switching time. In this thesis, a more efficient multi-step bandwidth-switching scheme is proposed that can significantly reduce the total switching time by minimizing the effect of secondary glitches. After satisfactory behavioral simulations, a proof-of-concept test chip integrating a 2.4GHz Integer-N synthesizer is designed and fabricated in the TSMC 0.25mum mixed-signal CMOS process. Simulations using time contraction show that the synthesizer switches 14% faster in the four-step mode compared to the one-step mode for a frequency step of 20MHz and 0.1% error tolerance
Recommended from our members
Architectures and Circuits Leveraging Injection-Locked Oscillators for Ultra-Low Voltage Clock Synthesis and Reference-less Receivers for Dense Chip-to-Chip Communications
High performance computing is critical for the needs of scientific discovery and economic competitiveness. An extreme-scale computing system at 1000x the performance of today’s petaflop machines will exhibit massive parallelism on multiple vertical fronts, from thousands of computational units on a single processor to thousands of processors in a single data center. To facilitate such a massively-parallel extreme-scale computing, a key challenge is power. The challenge is not power associated with base computation but rather the problem of transporting data from one chip to another at high enough rates. This thesis presents architectures and techniques to achieve low power and area footprint while achieving high data rates in a dense very-short reach (VSR) chip-to-chip (C2C) communication network. High-speed serial communication operating at ultra-low supplies improves the energy-efficiency and lowers the power envelop of a system doing an exaflop of loops. One focus area of this thesis is clock synthesis for such energy-efficient interconnect applications operating at high speeds and ultra-low supplies. A sub-integer clockfrequency synthesizer is presented that incorporates a multi-phase injection-locked ring-oscillator-based prescaler for operation at an ultra-low supply voltage of 0.5V, phase-switching based programmable division for sub-integer clock-frequency synthesis, and automatic calibration to ensure injection lock. A record speed of 9GHz has been demonstrated at 0.5V in 45nm SOI CMOS. It consumes 3.5mW of power at 9.12GHz and 0.052 of area, while showing an output phase noise of -100dBc/Hz at 1MHz offset and RMS jitter of 325fs; it achieves a net of -186.5 in a 45-nm SOI CMOS process. This thesis also describes a receiver with a reference-less clocking architecture for high-density VSR-C2C links. This architecture simplifies clock-tree planning in dense extreme-scaling computing environments and has high-bandwidth CDR to enable SSC for suppressing EMI and to mitigate TX jitter requirements. It features clock-less DFE and a high-bandwidth CDR based on master-slave ILOs for phase generation/rotation. The RX is implemented in 14nm CMOS and characterized at 19Gb/s. It is 1.5x faster that previous reference-less embedded-oscillator based designs with greater than 100MHz jitter tolerance bandwidth and recovers error-free data over VSR-C2C channels. It achieves a power-efficiency of 2.9pJ/b while recovering error-free data (BER 200MHz and the INL of the ILO-based phase-rotator (32- Steps/UI) is <1-LSB. Lastly, this thesis develops a time-domain delay-based modeling of injection locking to describe injection-locking phenomena in nonharmonic oscillators. The model is used to predict the locking bandwidth, and the locking dynamics of the locked oscillator. The model predictions are verified against simulations and measurements of a four-stage differential ring oscillator. The model is further used to predict the injection-locking behavior of a single-ended CMOS inverter based ring oscillator, the lock range of a multi-phase injection-locked ring-oscillator-based prescaler, as well as the dynamics of tracking injection phase perturbations in injection-locked masterslave oscillators; demonstrating its versatility in application to any nonharmonic oscillator
Process and Temperature Compensated Wideband Injection Locked Frequency Dividers and their Application to Low-Power 2.4-GHz Frequency Synthesizers
There has been a dramatic increase in wireless awareness among the user community in the past five years. The 2.4-GHz Industrial, Scientific and Medical (ISM) band is being used for a diverse range of applications due to the following reasons. It is the only unlicensed band approved worldwide and it offers more bandwidth and supports higher data rates compared to the 915-MHz ISM band. The power consumption of devices utilizing the 2.4-GHz band is much lower compared to the 5.2-GHz ISM band. Protocols like Bluetooth and Zigbee that utilize the 2.4-GHz ISM band are becoming extremely popular.
Bluetooth is an economic wireless solution for short range connectivity between PC, cell phones, PDAs, Laptops etc. The Zigbee protocol is a wireless technology that was developed as an open global standard to address the unique needs of low-cost, lowpower, wireless sensor networks. Wireless sensor networks are becoming ubiquitous, especially after the recent terrorist activities. Sensors are employed in strategic locations for real-time environmental monitoring, where they collect and transmit data frequently to a nearby terminal. The devices operating in this band are usually compact and battery powered. To enhance battery life and avoid the cumbersome task of battery replacement, the devices used should consume extremely low power. Also, to meet the growing demands cost and sized has to be kept low which mandates fully monolithic implementation using low cost process.
CMOS process is extremely attractive for such applications because of its low cost and the possibility to integrate baseband and high frequency circuits on the same chip. A fully integrated solution is attractive for low power consumption as it avoids the need for power hungry drivers for driving off-chip components. The transceiver is often the most power hungry block in a wireless communication system. The frequency divider (prescaler) and the voltage controlled oscillator in the transmitter’s frequency synthesizer are among the major sources of power consumption. There have been a number of publications in the past few decades on low-power high-performance VCOs. Therefore this work focuses on prescalers.
A class of analog frequency dividers called as Injection-Locked Frequency Dividers (ILFD) was introduced in the recent past as low power frequency division. ILFDs can consume an order of magnitude lower power when compared to conventional flip-flop based dividers. However the range of operation frequency also knows as the locking range is limited. ILFDs can be classified as LC based and Ring based. Though LC based are insensitive to process and temperature variation, they cannot be used for the 2.4-GHz ISM band because of the large size of on-chip inductors at these frequencies. This causes a lot of valuable chip area to be wasted. Ring based ILFDs are compact and provide a low power solution but are extremely sensitive to process and temperature variations. Process and temperature variation can cause ring based ILFD to loose lock in the desired operating band.
The goal of this work is to make the ring based ILFDs useful for practical applications. Techniques to extend the locking range of the ILFDs are discussed. A novel and simple compensation technique is devised to compensate the ILFD and keep the locking range tight with process and temperature variations. The proposed ILFD is used in a 2.4-GHz frequency synthesizer that is optimized for fractional-N synthesis. Measurement results supporting the theory are provided
Relationships Between the Performance of Time/Frequency Standards and Navigation/Communication Systems
The relationship between system performance and clock or oscillator performance is discussed. Tradeoffs discussed include: short term stability versus bandwidth requirements; frequency accuracy versus signal acquisition time; flicker of frequency and drift versus resynchronization time; frequency precision versus communications traffic volume; spectral purity versus bit error rate, and frequency standard stability versus frequency selection and adjustability. The benefits and tradeoffs of using precise frequency and time signals are various levels of precision and accuracy are emphasized
Recommended from our members
High Performance Local Oscillator Design for Next Generation Wireless Communication
Local Oscillator (LO) is an essential building block in modern wireless radios. In modern wireless radios, LO often serves as a reference of the carrier signal to modulate or demod- ulate the outgoing or incoming data. The LO signal should be a clean and stable source, such that the frequency or timing information of the carrier reference can be well-defined. However, as radio architecture evolves, the importance of LO path design has become much more important than before. Of late, many radio architecture innovations have exploited sophisticated LO generation schemes to meet the ever-increasing demands of wireless radio performances.
The focus of this thesis is to address challenges in the LO path design for next-generation high performance wireless radios. These challenges include (1) Congested spectrum at low radio frequency (RF) below 5GHz (2) Continuing miniaturization of integrated wireless radio, and (3) Fiber-fast (>10Gb/s) mm-wave wireless communication.
The thesis begins with a brief introduction of the aforementioned challenges followed by a discussion of the opportunities projected to overcome these challenges.
To address the challenge of congested spectrum at frequency below 5GHz, novel ra- dio architectures such as cognitive radio, software-defined radio, and full-duplex radio have drawn significant research interest. Cognitive radio is a radio architecture that opportunisti- cally utilize the unused spectrum in an environment to maximize spectrum usage efficiency. Energy-efficient spectrum sensing is the key to implementing cognitive radio. To enable energy-efficient spectrum sensing, a fast-hopping frequency synthesizer is an essential build- ing block to swiftly sweep the carrier frequency of the radio across the available spectrum. Chapter 2 of this thesis further highlights the challenges and trade-offs of the current LO gen-
eration scheme for possible use in sweeping LO-based spectrum analysis. It follows by intro- duction of the proposed fast-hopping LO architecture, its implementation and measurement results of the validated prototype. Chapter 3 proposes an embedded phase-shifting LO-path design for wideband RF self-interference cancellation for full-duplex radio. It demonstrates a synergistic design between the LO path and signal to perform self-interference cancellation.
To address the challenge of continuing miniaturization of integrated wireless radio, ring oscillator-based frequency synthesizer is an attractive candidate due to its compactness. Chapter 4 discussed the difficulty associated with implementing a Phase-Locked Loop (PLL) with ultra-small form-factor. It further proposes the concept sub-sampling PLL with time- based loop filter to address these challenges. A 65nm CMOS prototype and its measurement result are presented for validation of the concept.
In shifting from RF to mm-wave frequencies, the performance of wireless communication links is boosted by significant bandwidth and data-rate expansion. However, the demand for data-rate improvement is out-pacing the innovation of radio architectures. A >10Gb/s mm-wave wireless communication at 60GHz is required by emerging applications such as virtual-reality (VR) headsets, inter-rack data transmission at data center, and Ultra-High- Definition (UHD) TV home entertainment systems. Channel-bonding is considered to be a promising technique for achieving >10Gb/s wireless communication at 60GHz. Chapter 5 discusses the fundamental radio implementation challenges associated with channel-bonding for 60GHz wireless communication and the pros and cons of prior arts that attempted to address these challenges. It is followed by a discussion of the proposed 60GHz channel- bonding receiver, which utilizes only a single PLL and enables both contiguous and non- contiguous channel-bonding schemes.
Finally, Chapter 6 presents the conclusion of this thesis
Programmable rate modem utilizing digital signal processing techniques
The engineering development study to follow was written to address the need for a Programmable Rate Digital Satellite Modem capable of supporting both burst and continuous transmission modes with either binary phase shift keying (BPSK) or quadrature phase shift keying (QPSK) modulation. The preferred implementation technique is an all digital one which utilizes as much digital signal processing (DSP) as possible. Here design tradeoffs in each portion of the modulator and demodulator subsystem are outlined, and viable circuit approaches which are easily repeatable, have low implementation losses and have low production costs are identified. The research involved for this study was divided into nine technical papers, each addressing a significant region of concern in a variable rate modem design. Trivial portions and basic support logic designs surrounding the nine major modem blocks were omitted. In brief, the nine topic areas were: (1) Transmit Data Filtering; (2) Transmit Clock Generation; (3) Carrier Synthesizer; (4) Receive AGC; (5) Receive Data Filtering; (6) RF Oscillator Phase Noise; (7) Receive Carrier Selectivity; (8) Carrier Recovery; and (9) Timing Recovery
Astronomical spectrograph calibration with broad-spectrum frequency combs
Broadband femtosecond-laser frequency combs are filtered to
spectrographically resolvable frequency-mode spacing, and the limitations of
using cavities for spectral filtering are considered. Data and theory are used
to show implications to spectrographic calibration of high-resolution,
astronomical spectrometers
- …