Process and Temperature Compensated Wideband Injection Locked Frequency Dividers and their Application to Low-Power 2.4-GHz Frequency Synthesizers

There has been a dramatic increase in wireless awareness among the user community in the past five years. The 2.4-GHz Industrial, Scientific and Medical (ISM) band is being used for a diverse range of applications due to the following reasons. It is the only unlicensed band approved worldwide and it offers more bandwidth and supports higher data rates compared to the 915-MHz ISM band. The power consumption of devices utilizing the 2.4-GHz band is much lower compared to the 5.2-GHz ISM band. Protocols like Bluetooth and Zigbee that utilize the 2.4-GHz ISM band are becoming extremely popular. Bluetooth is an economic wireless solution for short range connectivity between PC, cell phones, PDAs, Laptops etc. The Zigbee protocol is a wireless technology that was developed as an open global standard to address the unique needs of low-cost, lowpower, wireless sensor networks. Wireless sensor networks are becoming ubiquitous, especially after the recent terrorist activities. Sensors are employed in strategic locations for real-time environmental monitoring, where they collect and transmit data frequently to a nearby terminal. The devices operating in this band are usually compact and battery powered. To enhance battery life and avoid the cumbersome task of battery replacement, the devices used should consume extremely low power. Also, to meet the growing demands cost and sized has to be kept low which mandates fully monolithic implementation using low cost process. CMOS process is extremely attractive for such applications because of its low cost and the possibility to integrate baseband and high frequency circuits on the same chip. A fully integrated solution is attractive for low power consumption as it avoids the need for power hungry drivers for driving off-chip components. The transceiver is often the most power hungry block in a wireless communication system. The frequency divider (prescaler) and the voltage controlled oscillator in the transmitter’s frequency synthesizer are among the major sources of power consumption. There have been a number of publications in the past few decades on low-power high-performance VCOs. Therefore this work focuses on prescalers. A class of analog frequency dividers called as Injection-Locked Frequency Dividers (ILFD) was introduced in the recent past as low power frequency division. ILFDs can consume an order of magnitude lower power when compared to conventional flip-flop based dividers. However the range of operation frequency also knows as the locking range is limited. ILFDs can be classified as LC based and Ring based. Though LC based are insensitive to process and temperature variation, they cannot be used for the 2.4-GHz ISM band because of the large size of on-chip inductors at these frequencies. This causes a lot of valuable chip area to be wasted. Ring based ILFDs are compact and provide a low power solution but are extremely sensitive to process and temperature variations. Process and temperature variation can cause ring based ILFD to loose lock in the desired operating band. The goal of this work is to make the ring based ILFDs useful for practical applications. Techniques to extend the locking range of the ILFDs are discussed. A novel and simple compensation technique is devised to compensate the ILFD and keep the locking range tight with process and temperature variations. The proposed ILFD is used in a 2.4-GHz frequency synthesizer that is optimized for fractional-N synthesis. Measurement results supporting the theory are provided

A Low-Power BFSK/OOK Transmitter for Wireless Sensors

In recent years, significant improvements in semiconductor technology have allowed consistent development of wireless chipsets in terms of functionality and form factor. This has opened up a broad range of applications for implantable wireless sensors and telemetry devices in multiple categories, such as military, industrial, and medical uses. The nature of these applications often requires the wireless sensors to be low-weight and energy-efficient to achieve long battery life. Among the various functions of these sensors, the communication block, used to transmit the gathered data, is typically the most power-hungry block. In typical wireless sensor networks, transmission range is below 10 meters and required radiated power is below 1 milliwatt. In such cases, power consumption of the frequency-synthesis circuits prior to the power amplifier of the transmitter becomes significant. Reducing this power consumption is currently the focus of various research endeavors. A popular method of achieving this goal is using a direct-modulation transmitter where the generated carrier is directly modulated with baseband data using simple modulation schemes. Among the different variations of direct-modulation transmitters, transmitters using unlocked digitally-controlled oscillators and transmitters with injection or resonator-locked oscillators are widely investigated because of their simple structure. These transmitters can achieve low-power and stable operation either with the help of recalibration or by sacrificing tuning capability. In contrast, phase-locked-loop-based (PLL) transmitters are less researched. The PLL uses a feedback loop to lock the carrier to a reference frequency with a programmable ratio and thus achieves good frequency stability and convenient tunability. This work focuses on PLL-based transmitters. The initial goal of this work is to reduce the power consumption of the oscillator and frequency divider, the two most power-consuming blocks in a PLL. Novel topologies for these two blocks are proposed which achieve ultra-low-power operation. Along with measured performance, mathematical analysis to derive rule-of-thumb design approaches are presented. Finally, the full transmitter is implemented using these blocks in a 130 nanometer CMOS process and is successfully tested for low-power operation

LOW PHASE NOISE CMOS PLL FREQUENCY SYNTHESIZER DESIGN AND ANALYSIS

The phase-locked loop (PLL) frequency synthesizer is a critical device of wireless transceivers. It works as a local oscillator (LO) for frequency translation and channel selection in the transceivers but suffers phase noise including reference spurs. In this dissertation for lowing phase noise and power consumption, efforts are placed on the new design of PLL components: VCOs, charge pumps and sigma delta modulators. Based on the analysis of the VCO phase noise generation mechanism and improving on the literature results, a design-oriented phase noise model for a complementary cross-coupled LC VCO is provided. The model reveals the relationship between the phase noise performance and circuit design parameters. Using this phase noise model, an optimized 2GHz low phase noise CMOS LC VCO is designed, simulated and fabricated. The theoretical analysis results are confirmed by the simulation and experimental results. With this VCO phase noise model, we also design a low phase noise, low gain wideband VCO with the typical VCO gain around 100MHz/V. Improving upon literature results, a complete quantitative analysis of reference spur is given in this dissertation. This leads to a design of a charge pump by using a negative feedback circuit and replica bias to reduce the current mismatch which causes the reference spur. In addition, low-impedance charge/discharge paths are provided to overcome the charge pump current glitches which also cause PLL spurs. With a large bit-width high order sigma delta modulator, the fractional-N PLL has fine frequency resolution and fast locking time. Based on an analysis of sigma delta modulator models introduced in this dissertation, a 3rd-order MASH 1-1-1 digital sigma delta modulator is designed. Pipelining techniques and true single phase clock (TSPC) techniques are used for saving power and area. Included is the design of a fully integrated 2.4GHz §¢ fractional-N CMOS PLL frequency synthesizer. It takes advantage of a sigma delta modulator to get a very fine frequency resolution and a relatively large loop bandwidth. This frequency synthesizer is a 4th-order charge pump PLL with 26MHz reference frequency. The loop bandwidth is about 150KHz, while the whole PLL phase noise is about -120dBc/Hz at 1MHz frequency offset

A low phase noise ring oscillator phase-locked loop for wireless applications

Thesis (M. Eng.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2005.Includes bibliographical references (p. 129).This thesis describes the circuit level design of a 900MHz [Sigma][Detta] ring oscillator based phase-locked loop using 0.35[mu]m technology. Multiple phase noise theories are considered giving insight into low phase-noise voltage controlled oscillator design. The circuit utilizes a fully symmetric differential voltage controlled oscillator with cascode current starved inverters to reduces current noise. A compact multi-modulus prescaler is presented, based on modified true single-phase clock flip-flops with integrated logic. A fully differential charge pump with switched-capacitor common mode feedback is utilized in conjunction with a nonlinear phase-frequency detector for accelerated acquisition time.by Colin Weltin-Wu.M.Eng

Design of frequency synthesizers for short range wireless transceivers

The rapid growth of the market for short-range wireless devices, with standards such as Bluetooth and Wireless LAN (IEEE 802.11) being the most important, has created a need for highly integrated transceivers that target drastic power and area reduction while providing a high level of integration. The radio section of the devices designed to establish communications using these standards is the limiting factor for the power reduction efforts. A key building block in a transceiver is the frequency synthesizer, since it operates at the highest frequency of the system and consumes a very large portion of the total power in the radio. This dissertation presents the basic theory and a design methodology of frequency synthesizers targeted for short-range wireless applications. Three different examples of synthesizers are presented. First a frequency synthesizer integrated in a Bluetooth receiver fabricated in 0.35μm CMOS technology. The receiver uses a low-IF architecture to downconvert the incoming Bluetooth signal to 2MHz. The second synthesizer is integrated within a dual-mode receiver capable of processing signals of the Bluetooth and Wireless LAN (IEEE 802.11b) standards. It is implemented in BiCMOS technology and operates the voltage controlled oscillator at twice the required frequency to generate quadrature signals through a divide-by-two circuit. A phase switching prescaler is featured in the synthesizer. A large capacitance is integrated on-chip using a capacitance multiplier circuit that provides a drastic area reduction while adding a negligible phase noise contribution. The third synthesizer is an extension of the second example. The operation range of the VCO is extended to cover a frequency band from 4.8GHz to 5.85GHz. By doing this, the synthesizer is capable of generating LO signals for Bluetooth and IEEE 802.11a, b and g standards. The quadrature output of the 5 - 6 GHz signal is generated through a first order RC - CR network with an automatic calibration loop. The loop uses a high frequency phase detector to measure the deviation from the 90° separation between the I and Q branches and implements an algorithm to minimize the phase errors between the I and Q branches and their differential counterparts

A high-frequency quad-modulus prescaler for fractional-N frequency synthesizer

Master'sMASTER OF ENGINEERIN

Second year technical report on-board processing for future satellite communications systems

Advanced baseband and microwave switching techniques for large domestic communications satellites operating in the 30/20 GHz frequency bands are discussed. The nominal baseband processor throughput is one million packets per second (1.6 Gb/s) from one thousand T1 carrier rate customer premises terminals. A frequency reuse factor of sixteen is assumed by using 16 spot antenna beams with the same 100 MHz bandwidth per beam and a modulation with a one b/s per Hz bandwidth efficiency. Eight of the beams are fixed on major metropolitan areas and eight are scanning beams which periodically cover the remainder of the U.S. under dynamic control. User signals are regenerated (demodulated/remodulated) and message packages are reformatted on board. Frequency division multiple access and time division multiplex are employed on the uplinks and downlinks, respectively, for terminals within the coverage area and dwell interval of a scanning beam. Link establishment and packet routing protocols are defined. Also described is a detailed design of a separate 100 x 100 microwave switch capable of handling nonregenerated signals occupying the remaining 2.4 GHz bandwidth with 60 dB of isolation, at an estimated weight and power consumption of approximately 400 kg and 100 W, respectively

Low jitter phase-locked loop clock synthesis with wide locking range

The fast growing demand of wireless and high speed data communications has driven efforts to increase the levels of integration in many communications applications. Phase noise and timing jitter are important design considerations for these communications applications. The desire for highly complex levels of integration using low cost CMOS technologies works against the minimization of timing jitter and phase noise for communications systems which employ a phase-locked loop for frequency and clock synthesis with on-chip VCO. This dictates an integrated CMOS implementation of the VCO with very low phase noise performance. The ring oscillator VCOs based on differential delay cell chains have been used successfully in communications applications, but thermal noise induced phase noise have to be minimized in order not to limit their applicability to some applications which impose stringent timing jitter and phase noise requirements on the PLL clock synthesizer. Obtaining lower timing jitter and phase noise at the PLL output also requires the minimization of noise in critical circuit design blocks as well as the optimization of the loop bandwidth of the PLL. In this dissertation the fundamental performance limits of CMOS PLL clock synthesizers based on ring oscillator VCOs are investigated. The effect of flicker and thermal noise in MOS transistors on timing jitter and phase noise are explored, with particular emphasis on source coupled NMOS differential delay cells with symmetric load elements. Several new circuit architectures are employed for the charge pump circuit and phase-frequency detector (PFD) to minimize the timing jitter due to the finite dead zone in the PFD and the current mismatch in the charge pump circuit. The selection of the optimum PLL loop bandwidth is critical in determining the phase noise performance at the PLL output. The optimum loop bandwidth and the phase noise performance of the PLL is determined using behavioral simulations. These results are compared with transistor level simulated results and experimental results for the PLL clock synthesizer fabricated in a 0.35 µm CMOS technology with good agreement. To demonstrate the proposed concept, a fully integrated CMOS PLL clock synthesizer utilizing integer-N frequency multiplier technique to synthesize several clock signals in the range of 20-400 MHz with low phase noise was designed. Implemented in a standard 0.35-µm N-well CMOS process technology, the PLL achieves a period jitter of 6.5-ps (rms) and 38-ps (peak-to-peak) at 216 MHz with a phase noise of -120 dBc/Hz at frequency offsets above 10 KHz. The specific research contributions of this work include (1) proposing, designing, and implementing a new charge pump circuit architecture that matches current levels and therefore minimizes one source of phase noise due to fluctuations in the control voltage of the VCO, (2) an improved phase-frequency detector architecture which has improved characteristics in lock condition, (3) an improved ring oscillator VCO with excellent thermal noise induced phase noise characteristics, (4) the application of selfbiased techniques together with fixed bias to CMOS low phase noise PLL clock synthesizer for digital video communications ,and (5) an analytical model that describes the phase noise performance of the proposed VCO and PLL clock synthesizer

Design of CMOS integrated frequency synthesizers for ultra-wideband wireless communications systems

Ultra¬wide band (UWB) system is a breakthrough in wireless communication, as it provides data rate one order higher than existing ones. This dissertation focuses on the design of CMOS integrated frequency synthesizer and its building blocks used in UWB system. A mixer¬based frequency synthesizer architecture is proposed to satisfy the agile frequency hopping requirement, which is no more than 9.5 ns, three orders faster than conventional phase¬locked loop (PLL)¬based synthesizers. Harmonic cancela¬tion technique is extended and applied to suppress the undesired harmonic mixing components. Simulation shows that sidebands at 2.4 GHz and 5 GHz are below 36 dBc from carrier. The frequency synthesizer contains a novel quadrature VCO based on the capacitive source degeneration structure. The QVCO tackles the jeopardous ambiguity of the oscillation frequency in conventional QVCOs. Measurement shows that the 5¬GHz CSD¬QVCO in 0.18 µm CMOS technology draws 5.2 mA current from a 1.2 V power supply. Its phase noise is ¬120 dBc at 3 MHz offset. Compared with existing phase shift LC QVCOs, the proposed CSD¬QVCO presents better phase noise and power efficiency. Finally, a novel injection locking frequency divider (ILFD) is presented. Im¬plemented with three stages in 0.18 µm CMOS technology, the ILFD draws 3¬mA current from a 1.8¬V power supply. It achieves multiple large division ratios as 6, 12, and 18 with all locking ranges greater than 1.7 GHz and injection frequency up to 11 GHz. Compared with other published ILFDs, the proposed ILFD achieves the largest division ratio with satisfactory locking range

CMOS dual-modulus prescaler design for RF frequency synthesizer applications.

Ng Chong Chon.Thesis (M.Phil.)--Chinese University of Hong Kong, 2005.Includes bibliographical references (leaves 100-103).Abstract in English and Chinese.摘要 --- p.iiiAcknowledgments --- p.ivContents --- p.viList of Figures --- p.ixList of Tables --- p.xiiChapter Chapter 1 --- Introduction --- p.1Chapter 1.1 --- Motivation --- p.1Chapter 1.2 --- Thesis Organization --- p.4Chapter Chapter 2 --- DMP Architecture --- p.6Chapter 2.1 --- Conventional DMP --- p.6Chapter 2.1.1 --- Operating Principle --- p.7Chapter 2.1.2 --- Disadvantages --- p.10Chapter 2.2 --- Pre-processing Clock Architecture --- p.10Chapter 2.2.1 --- Operating Principle --- p.11Chapter 2.2.2 --- Advantages and Disadvantages --- p.12Chapter 2.3 --- Phase-switching Architecture --- p.13Chapter 2.3.1 --- Operating Principle --- p.13Chapter 2.3.2 --- Advantages and Disadvantages --- p.14Chapter 2.4 --- Summary --- p.15Chapter Chapter 3 --- Full-Speed Divider Design --- p.16Chapter 3.1 --- Introduction --- p.16Chapter 3.2 --- Working Principle --- p.16Chapter 3.3 --- Design Issues --- p.18Chapter 3.4 --- Device Sizing --- p.19Chapter 3.5 --- Layout Considerations --- p.20Chapter 3.6 --- Input Sensitivity --- p.22Chapter 3.7 --- Modeling --- p.24Chapter 3.8 --- Review on Different Divider Designs --- p.28Chapter 3.8.1 --- Divider with Dynamic-Loading Technique --- p.28Chapter 3.8.2 --- Divider with Negative-Slew Technique --- p.30Chapter 3.8.3 --- LC Injection-Locked Frequency Divider --- p.32Chapter 3.8.4 --- Dynamic True Single Phase Clock Frequency Divider --- p.34Chapter 3.9 --- Summary --- p.42Chapter Chapter 4 --- 3V 900MHz Low Noise DMP --- p.43Chapter 4.1 --- Introduction --- p.43Chapter 4.2 --- Proposed DMP Topology --- p.46Chapter 4.3 --- Circuit Design and Implementation --- p.49Chapter 4.4 --- Simulation Results --- p.51Chapter 4.5 --- Summary --- p.53Chapter Chapter 5 --- 1.5V 2.4GHz Low Power DMP --- p.54Chapter 5.1 --- Introduction --- p.54Chapter 5.2 --- Proposed DMP Topology --- p.56Chapter 5.3 --- Circuit Design and Implementation --- p.59Chapter 5.3.1 --- Divide-by-4 stage --- p.59Chapter 5.3.2 --- TSPC dividers --- p.63Chapter 5.3.3 --- Phase-selection Network --- p.63Chapter 5.3.4 --- Mode-control Logic --- p.64Chapter 5.3.5 --- Duty-cycle Transformer --- p.65Chapter 5.3.6 --- Glitch Problem --- p.66Chapter 5.3.7 --- Phase-mismatch Problem --- p.70Chapter 5.4 --- Simulation Results --- p.70Chapter 5.5 --- Summary --- p.74Chapter Chapter 6 --- 1.5V 2.4GHz Wideband DMP --- p.75Chapter 6.1 --- Introduction --- p.75Chapter 6.2 --- Proposed DMP Architecture --- p.75Chapter 6.3 --- Divide-by-4 Stage --- p.76Chapter 6.3.1 --- Current-switch Combining --- p.76Chapter 6.3.2 --- Capacitive Load Reduction --- p.77Chapter 6.4 --- Simulation Results --- p.81Chapter 6.5 --- Summary --- p.83Chapter Chapter 7 --- Experimental Results --- p.84Chapter 7.1 --- Introduction --- p.84Chapter 7.2 --- Equipment Setup --- p.84Chapter 7.3 --- Measurement Results --- p.85Chapter 7.3.1 --- 3V 900GHz Low Noise DMP --- p.85Chapter 7.3.2 --- 1.5V 2.4GHz Low Power DMP --- p.88Chapter 7.3.3 --- 1.5V 2.4GHz Wideband DMP --- p.93Chapter 7.3 --- Summary --- p.96Chapter Chapter 8 --- Conclusions and Future Works --- p.98Chapter 8.1 --- Conclusions --- p.98Chapter 8.2 --- Future Works --- p.99References --- p.100Publications --- p.10