2D Parity Product Code for TSV online fault correction and detection

Through-Silicon-Via (TSV) is one of the most promising technologies to realize 3D Integrated Circuits (3D-ICs).  However, the reliability issues due to the low yield rates and the sensitivity to thermal hotspots and stress issues are preventing TSV-based 3D-ICs from being widely and efficiently used. To enhance the reliability of TSV connections, using error correction code to detect and correct faults automatically has been demonstrated as a viable solution.This paper presents a 2D Parity Product Code (2D-PPC) for TSV fault-tolerance with the ability to correct one fault and detect, at least, two faults.  In an implementation of 64-bit data and 81-bit codeword, 2D-PPC can detect over 71 faults, on average. Its encoder and decoder decrease the overall latency by 38.33% when compared to the Single Error Correction Double Error Detection code.  In addition to the high detection rates, the encoder can detect 100% of its gate failures, and the decoder can detect and correct around 40% of its individual gate failures. The squared 2D-PPC could be extended using orthogonal Latin square to support extra bit correction

On Energy Efficient Computing Platforms

In accordance with the Moore's law, the increasing number of on-chip integrated transistors has enabled modern computing platforms with not only higher processing power but also more affordable prices. As a result, these platforms, including portable devices, work stations and data centres, are becoming an inevitable part of the human society. However, with the demand for portability and raising cost of power, energy efficiency has emerged to be a major concern for modern computing platforms. As the complexity of on-chip systems increases, Network-on-Chip (NoC) has been proved as an efficient communication architecture which can further improve system performances and scalability while reducing the design cost. Therefore, in this thesis, we study and propose energy optimization approaches based on NoC architecture, with special focuses on the following aspects. As the architectural trend of future computing platforms, 3D systems have many bene ts including higher integration density, smaller footprint, heterogeneous integration, etc. Moreover, 3D technology can signi cantly improve the network communication and effectively avoid long wirings, and therefore, provide higher system performance and energy efficiency. With the dynamic nature of on-chip communication in large scale NoC based systems, run-time system optimization is of crucial importance in order to achieve higher system reliability and essentially energy efficiency. In this thesis, we propose an agent based system design approach where agents are on-chip components which monitor and control system parameters such as supply voltage, operating frequency, etc. With this approach, we have analysed the implementation alternatives for dynamic voltage and frequency scaling and power gating techniques at different granularity, which reduce both dynamic and leakage energy consumption. Topologies, being one of the key factors for NoCs, are also explored for energy saving purpose. A Honeycomb NoC architecture is proposed in this thesis with turn-model based deadlock-free routing algorithms. Our analysis and simulation based evaluation show that Honeycomb NoCs outperform their Mesh based counterparts in terms of network cost, system performance as well as energy efficiency.Siirretty Doriast

Towards a scalable and reliable wireless network-on-chip

Multi-core platforms are emerging trends in the design of Systems-on-Chip (SoCs). Interconnect fabrics for these multi-core SoCs play a crucial role in achieving the target performance. The Network-on-Chip (NoC) paradigm has been proposed as a promising solution for designing the interconnect fabric of multi-core SoCs. But the performance requirements of NoC infrastructures in future technology nodes cannot be met by relying only on material innovation with traditional scaling. The continuing demand for low power and high speed interconnects with technology scaling necessitates looking beyond the conventional planar metal/dielectric-based interconnect infrastructures. Among different possible alternatives, the on-chip wireless communication network is envisioned as a revolutionary methodology, capable of bringing significant performance gains for multi-core SoCs. Wireless NoCs (WiNoCs) can be designed by using miniaturized on-chip antennas as an enabling technology. In this work, design methodologies and technology requirements for scalable WiNoC architectures are presented and their performance is evaluated. It is demonstrated that WiNoCs outperform their wired counterparts in terms of network throughput and latency, and that energy dissipation improves by orders of magnitude under various experimental and real-life scenarios. A major challenge that NoC design is expected to face is related to the intrinsic unreliability of the interconnect infrastructure under technology limitations. The devices and components of the WiNoCs are expected to suffer high failure rates. By incorporating error control coding (ECC) schemes along the interconnects, NoC architectures will be able to provide correct functionality even in the presence of different sources of transient noise and yet have low energy dissipation. In this work, designs of novel joint crosstalk avoidance and multiple error correction/detection codes as well as burst error correction codes are proposed and their performance is evaluated in different WiNoC fabrics. It is demonstrated that by using the proposed codes WiNoCs can achieve the same reliability as a wireline NoC with much less energy dissipation and higher performance

Network-on-Chip

Addresses the Challenges Associated with System-on-Chip Integration Network-on-Chip: The Next Generation of System-on-Chip Integration examines the current issues restricting chip-on-chip communication efficiency, and explores Network-on-chip (NoC), a promising alternative that equips designers with the capability to produce a scalable, reusable, and high-performance communication backbone by allowing for the integration of a large number of cores on a single system-on-chip (SoC). This book provides a basic overview of topics associated with NoC-based design: communication infrastructure design, communication methodology, evaluation framework, and mapping of applications onto NoC. It details the design and evaluation of different proposed NoC structures, low-power techniques, signal integrity and reliability issues, application mapping, testing, and future trends. Utilizing examples of chips that have been implemented in industry and academia, this text presents the full architectural design of components verified through implementation in industrial CAD tools. It describes NoC research and developments, incorporates theoretical proofs strengthening the analysis procedures, and includes algorithms used in NoC design and synthesis. In addition, it considers other upcoming NoC issues, such as low-power NoC design, signal integrity issues, NoC testing, reconfiguration, synthesis, and 3-D NoC design. This text comprises 12 chapters and covers: The evolution of NoC from SoC—its research and developmental challenges NoC protocols, elaborating flow control, available network topologies, routing mechanisms, fault tolerance, quality-of-service support, and the design of network interfaces The router design strategies followed in NoCs The evaluation mechanism of NoC architectures The application mapping strategies followed in NoCs Low-power design techniques specifically followed in NoCs The signal integrity and reliability issues of NoC The details of NoC testing strategies reported so far The problem of synthesizing application-specific NoCs Reconfigurable NoC design issues Direction of future research and development in the field of NoC Network-on-Chip: The Next Generation of System-on-Chip Integration covers the basic topics, technology, and future trends relevant to NoC-based design, and can be used by engineers, students, and researchers and other industry professionals interested in computer architecture, embedded systems, and parallel/distributed systems

Exploration and Design of Power-Efficient Networked Many-Core Systems

Multiprocessing is a promising solution to meet the requirements of near future applications. To get full benefit from parallel processing, a manycore system needs efficient, on-chip communication architecture. Networkon- Chip (NoC) is a general purpose communication concept that offers highthroughput, reduced power consumption, and keeps complexity in check by a regular composition of basic building blocks. This thesis presents power efficient communication approaches for networked many-core systems. We address a range of issues being important for designing power-efficient manycore systems at two different levels: the network-level and the router-level. From the network-level point of view, exploiting state-of-the-art concepts such as Globally Asynchronous Locally Synchronous (GALS), Voltage/ Frequency Island (VFI), and 3D Networks-on-Chip approaches may be a solution to the excessive power consumption demanded by today’s and future many-core systems. To this end, a low-cost 3D NoC architecture, based on high-speed GALS-based vertical channels, is proposed to mitigate high peak temperatures, power densities, and area footprints of vertical interconnects in 3D ICs. To further exploit the beneficial feature of a negligible inter-layer distance of 3D ICs, we propose a novel hybridization scheme for inter-layer communication. In addition, an efficient adaptive routing algorithm is presented which enables congestion-aware and reliable communication for the hybridized NoC architecture. An integrated monitoring and management platform on top of this architecture is also developed in order to implement more scalable power optimization techniques. From the router-level perspective, four design styles for implementing power-efficient reconfigurable interfaces in VFI-based NoC systems are proposed. To enhance the utilization of virtual channel buffers and to manage their power consumption, a partial virtual channel sharing method for NoC routers is devised and implemented. Extensive experiments with synthetic and real benchmarks show significant power savings and mitigated hotspots with similar performance compared to latest NoC architectures. The thesis concludes that careful codesigned elements from different network levels enable considerable power savings for many-core systems.Siirretty Doriast

Embedded dynamic programming networks for networks-on-chip

PhD ThesisRelentless technology downscaling and recent technological advancements in three dimensional integrated circuit (3D-IC) provide a promising prospect to realize heterogeneous system-on-chip (SoC) and homogeneous chip multiprocessor (CMP) based on the networks-onchip (NoCs) paradigm with augmented scalability, modularity and performance. In many cases in such systems, scheduling and managing communication resources are the major design and implementation challenges instead of the computing resources. Past research efforts were mainly focused on complex design-time or simple heuristic run-time approaches to deal with the on-chip network resource management with only local or partial information about the network. This could yield poor communication resource utilizations and amortize the benefits of the emerging technologies and design methods. Thus, the provision for efficient run-time resource management in large-scale on-chip systems becomes critical. This thesis proposes a design methodology for a novel run-time resource management infrastructure that can be realized efficiently using a distributed architecture, which closely couples with the distributed NoC infrastructure. The proposed infrastructure exploits the global information and status of the network to optimize and manage the on-chip communication resources at run-time. There are four major contributions in this thesis. First, it presents a novel deadlock detection method that utilizes run-time transitive closure (TC) computation to discover the existence of deadlock-equivalence sets, which imply loops of requests in NoCs. This detection scheme, TC-network, guarantees the discovery of all true-deadlocks without false alarms in contrast to state-of-the-art approximation and heuristic approaches. Second, it investigates the advantages of implementing future on-chip systems using three dimensional (3D) integration and presents the design, fabrication and testing results of a TC-network implemented in a fully stacked three-layer 3D architecture using a through-silicon via (TSV) complementary metal-oxide semiconductor (CMOS) technology. Testing results demonstrate the effectiveness of such a TC-network for deadlock detection with minimal computational delay in a large-scale network. Third, it introduces an adaptive strategy to effectively diffuse heat throughout the three dimensional network-on-chip (3D-NoC) geometry. This strategy employs a dynamic programming technique to select and optimize the direction of data manoeuvre in NoC. It leads to a tool, which is based on the accurate HotSpot thermal model and SystemC cycle accurate model, to simulate the thermal system and evaluate the proposed approach. Fourth, it presents a new dynamic programming-based run-time thermal management (DPRTM) system, including reactive and proactive schemes, to effectively diffuse heat throughout NoC-based CMPs by routing packets through the coolest paths, when the temperature does not exceed chip’s thermal limit. When the thermal limit is exceeded, throttling is employed to mitigate heat in the chip and DPRTM changes its course to avoid throttled paths and to minimize the impact of throttling on chip performance. This thesis enables a new avenue to explore a novel run-time resource management infrastructure for NoCs, in which new methodologies and concepts are proposed to enhance the on-chip networks for future large-scale 3D integration.Iraqi Ministry of Higher Education and Scientific Research (MOHESR)

Développement d'architectures HW/SW tolérantes aux fautes et auto-calibrantes pour les technologies Intégrées 3D

Malgré les avantages de l'intégration 3D, le test, le rendement et la fiabilité des Through-Silicon-Vias (TSVs) restent parmi les plus grands défis pour les systèmes 3D à base de Réseaux-sur-Puce (Network-on-Chip - NoC). Dans cette thèse, une stratégie de test hors-ligne a été proposé pour les interconnections TSV des liens inter-die des NoCs 3D. Pour le TSV Interconnect Built-In Self-Test (TSV-IBIST) on propose une nouvelle stratégie pour générer des vecteurs de test qui permet la détection des fautes structuraux (open et short) et paramétriques (fautes de délaye). Des stratégies de correction des fautes transitoires et permanents sur les TSV sont aussi proposées aux plusieurs niveaux d'abstraction: data link et network. Au niveau data link, des techniques qui utilisent des codes de correction (ECC) et retransmission sont utilisées pour protégé les liens verticales. Des codes de correction sont aussi utilisés pour la protection au niveau network. Les défauts de fabrication ou vieillissement des TSVs sont réparé au niveau data link avec des stratégies à base de redondance et sérialisation. Dans le réseau, les liens inter-die défaillante ne sont pas utilisables et un algorithme de routage tolérant aux fautes est proposé. On peut implémenter des techniques de tolérance aux fautes sur plusieurs niveaux. Les résultats ont montré qu'une stratégie multi-level atteint des très hauts niveaux de fiabilité avec un cout plus bas. Malheureusement, il n'y as pas une solution unique et chaque stratégie a ses avantages et limitations. C'est très difficile d'évaluer tôt dans le design flow les couts et l'impact sur la performance. Donc, une méthodologie d'exploration de la résilience aux fautes est proposée pour les NoC 3D mesh.3D technology promises energy-efficient heterogeneous integrated systems, which may open the way to thousands cores chips. Silicon dies containing processing elements are stacked and connected by vertical wires called Through-Silicon-Vias. In 3D chips, interconnecting an increasing number of processing elements requires a scalable high-performance interconnect solution: the 3D Network-on-Chip. Despite the advantages of 3D integration, testing, reliability and yield remain the major challenges for 3D NoC-based systems. In this thesis, the TSV interconnect test issue is addressed by an off-line Interconnect Built-In Self-Test (IBIST) strategy that detects both structural (i.e. opens, shorts) and parametric faults (i.e. delays and delay due to crosstalk). The IBIST circuitry implements a novel algorithm based on the aggressor-victim scenario and alleviates limitations of existing strategies. The proposed Kth-aggressor fault (KAF) model assumes that the aggressors of a victim TSV are neighboring wires within a distance given by the aggressor order K. Using this model, TSV interconnect tests of inter-die 3D NoC links may be performed for different aggressor order, reducing test times and circuitry complexity. In 3D NoCs, TSV permanent and transient faults can be mitigated at different abstraction levels. In this thesis, several error resilience schemes are proposed at data link and network levels. For transient faults, 3D NoC links can be protected using error correction codes (ECC) and retransmission schemes using error detection (Automatic Retransmission Query) and correction codes (i.e. Hybrid error correction and retransmission).For transients along a source-destination path, ECC codes can be implemented at network level (i.e. Network-level Forward Error Correction). Data link solutions also include TSV repair schemes for faults due to fabrication processes (i.e. TSV-Spare-and-Replace and Configurable Serial Links) and aging (i.e. Interconnect Built-In Self-Repair and Adaptive Serialization) defects. At network-level, the faulty inter-die links of 3D mesh NoCs are repaired by implementing a TSV fault-tolerant routing algorithm. Although single-level solutions can achieve the desired yield / reliability targets, error mitigation can be realized by a combination of approaches at several abstraction levels. To this end, multi-level error resilience strategies have been proposed. Experimental results show that there are cases where this multi-layer strategy pays-off both in terms of cost and performance. Unfortunately, one-fits-all solution does not exist, as each strategy has its advantages and limitations. For system designers, it is very difficult to assess early in the design stages the costs and the impact on performance of error resilience. Therefore, an error resilience exploration (ERX) methodology is proposed for 3D NoCs.SAVOIE-SCD - Bib.électronique (730659901) / SudocGRENOBLE1/INP-Bib.électronique (384210012) / SudocGRENOBLE2/3-Bib.électronique (384219901) / SudocSudocFranceF

Cross-Layer Pathfinding for Off-Chip Interconnects

Off-chip interconnects for integrated circuits (ICs) today induce a diverse design space, spanning many different applications that require transmission of data at various bandwidths, latencies and link lengths. Off-chip interconnect design solutions are also variously sensitive to system performance, power and cost metrics, while also having a strong impact on these metrics. The costs associated with off-chip interconnects include die area, package (PKG) and printed circuit board (PCB) area, technology and bill of materials (BOM). Choices made regarding off-chip interconnects are fundamental to product definition, architecture, design implementation and technology enablement. Given their cross-layer impact, it is imperative that a cross-layer approach be employed to architect and analyze off-chip interconnects up front, so that a top-down design flow can comprehend the cross-layer impacts and correctly assess the system performance, power and cost tradeoffs for off-chip interconnects. Chip architects are not exposed to all the tradeoffs at the physical and circuit implementation or technology layers, and often lack the tools to accurately assess off-chip interconnects. Furthermore, the collaterals needed for a detailed analysis are often lacking when the chip is architected; these include circuit design and layout, PKG and PCB layout, and physical floorplan and implementation. To address the need for a framework that enables architects to assess the system-level impact of off-chip interconnects, this thesis presents power-area-timing (PAT) models for off-chip interconnects, optimization and planning tools with the appropriate abstraction using these PAT models, and die/PKG/PCB co-design methods that help expose the off-chip interconnect cross-layer metrics to the die/PKG/PCB design flows. Together, these models, tools and methods enable cross-layer optimization that allows for a top-down definition and exploration of the design space and helps converge on the correct off-chip interconnect implementation and technology choice. The tools presented cover off-chip memory interfaces for mobile and server products, silicon photonic interfaces, 2.5D silicon interposers and 3D through-silicon vias (TSVs). The goal of the cross-layer framework is to assess the key metrics of the interconnect (such as timing, latency, active/idle/sleep power, and area/cost) at an appropriate level of abstraction by being able to do this across layers of the design flow. In additional to signal interconnect, this thesis also explores the need for such cross-layer pathfinding for power distribution networks (PDN), where the system-on-chip (SoC) floorplan and pinmap must be optimized before the collateral layouts for PDN analysis are ready. Altogether, the developed cross-layer pathfinding methodology for off-chip interconnects enables more rapid and thorough exploration of a vast design space of off-chip parallel and serial links, inter-die and inter-chiplet links and silicon photonics. Such exploration will pave the way for off-chip interconnect technology enablement that is optimized for system needs. The basis of the framework can be extended to cover other interconnect technology as well, since it fundamentally relates to system-level metrics that are common to all off-chip interconnects

Towards Compelling Cases for the Viability of Silicon-Nanophotonic Technology in Future Many-core Systems

Many crossbenchmarking results reported in the open literature raise optimistic expectations on the use of optical networks-on-chip (ONoCs) for high-performance and low-power on-chip communications in future Manycore Systems. However, these works ultimately fail to make a compelling case for the viability of silicon-nanophotonic technology for two fundamental reasons: (1)Lack of aggressive electrical baselines (ENoCs). (2) Inaccuracy in physical- and architecture-layer analysis of the ONoC. This thesis aims at providing the guidelines and minimum requirements so that nanophotonic emerging technology may become of practical relevance. The key enabler for this study is a cross-layer design methodology of the optical transport medium, ranging from the consideration of the predictability gap between ONoC logic schemes and their physical implementations, up to architecture-level design issues such as the network interface and its co-design requirements with the memory hierarchy. In order to increase the practical relevance of the study, we consider a consolidated electrical NoC counterpart with an optimized architecture from a performance and power viewpoint. The quality metrics of this latter are derived from synthesis and place&route on an industrial 40nm low-power technology library. Building on this methodology, we are able to provide a realistic energy efficiency comparison between ONoC and ENoC both at the level of the system interconnect and of the system as a whole, pointing out the sensitivity of the results to the maturity of the underlying silicon nanophotonic technology, and at the same time paving the way towards compelling cases for the viability of such technology in next generation many-cores systems

Copper Electrodeposition in Mesoscale Through-Silicon-Vias

Copper (Cu) electrodeposition (ECD) in through-silicon-vias (TSVs) is an essential technique required for high-density 3-D integration of complex semiconductor devices. The importance of Cu ECD in damascene interconnects has led to a natural development towards copper electrodeposition in TSVs. Cu ECD is preferred over alternative approaches like the chemical vapor deposition (CVD) of tungsten (W) or aluminum (Al) because Cu ECD films have lower film stress, lower processing temperatures, and more optimal thermal and electrical properties as compared with CVD W or Al. Via filling with electroplated Cu on substrates that have undergone atomic layer deposition of a conformal platinum seed metal is investigated herein. These mesoscale vias (600 μm depth, 5:1 aspect ratio) will be utilized in ultra-high-vacuum systems and thus require a uniform, void-free Cu deposit of sufficient thickness to prevent device degradation due to skin effects when RF frequencies as high as 100 V at 100 MHz are used. Conformally Cu-lined TSVs are achieved through the implementation of a complex ECD parameter scheme, and these results are compared with computational finite element modeling (FEM) outcomes. A novel, single additive chemistry is also developed and implemented to achieve fully filled void-free mesoscale TSVs within 6 hours of plating time, which represents an extraordinarily fast and controllable plating rate (100 μm/hour) for interconnect (IC) feature filling