Digital Intensive Mixed Signal Circuits with In-situ Performance Monitors

University of Minnesota Ph.D. dissertation.November 2016. Major: Electrical/Computer Engineering. Advisor: Chris Kim. 1 computer file (PDF); x, 137 pages.Digital intensive circuit design techniques of different mixed-signal systems such as data converters, clock generators, voltage regulators etc. are gaining attention for the implementation of modern microprocessors and system-on-chips (SoCs) in order to fully utilize the benefits of CMOS technology scaling. Moreover different performance improvement schemes, for example, noise reduction, spur cancellation, linearity improvement etc. can be easily performed in digital domain. In addition to that, increasing speed and complexity of modern SoCs necessitate the requirement of in-situ measurement schemes, primarily for high volume testing. In-situ measurements not only obviate the need for expensive measurement equipments and probing techniques, but also reduce the test time significantly when a large number of chips are required to be tested. Several digital intensive circuit design techniques are proposed in this dissertation along with different in-situ performance monitors for a variety of mixed signal systems. First, a novel beat frequency quantization technique is proposed in a two-step VCO quantizer based ADC implementation for direct digital conversion of low amplitude bio- potential signals. By direct conversion, it alleviates the requirement of the area and power consuming analog-frontend (AFE) used in a conventional ADC designs. This prototype design is realized in a 65nm CMOS technology. Measured SNDR is 44.5dB from a 10mVpp, 300Hz signal and power consumption is only 38μW. Next, three different clock generation circuits, a phase-locked loop (PLL), a multiplying delay-locked loop (MDLL) and a frequency-locked loop (FLL) are presented. First a 0.4-to-1.6GHz sub-sampling fractional-N all digital PLL architecture is discussed that utilizes a D-flip-flop as a digital sub-sampler. Measurement results from a 65nm CMOS test-chip shows 5dB lower phase noise at 100KHz offset frequency, compared to a conventional architecture. The Digital PLL (DPLL) architecture is further extended for a digital MDLL implementation in order to suppress the VCO phase noise beyond the DPLL bandwidth. A zero-offset aperture phase detector (APD) and a digital- to-time converter (DTC) are employed for static phase-offset (SPO) cancellation. A unique in-situ detection circuitry achieves a high resolution SPO measurement in time domain. A 65nm test-chip shows 0.2-to-1.45GHz output frequency range while reducing the phase-noise by 9dB compared to a DPLL. Next, a frequency-to-current converter (FTC) based fractional FLL is proposed for a low accuracy clock generation in an extremely low area for IoT application. High density deep-trench capacitors are used for area reduction. The test-chip is fabricated in a 32nm SOI technology that takes only 0.0054mm2 active area. A high-resolution in-situ period jitter measurement block is also incorporated in this design. Finally, a time based digital low dropout (DLDO) regulator architecture is proposed for fine grain power delivery over a wide load current dynamic range and input/output voltage in order to facilitate dynamic voltage and frequency scaling (DVFS). High- resolution beat frequency detector dynamically adjusts the loop sampling frequency for ripple and settling time reduction due to load transients. A fixed steady-state voltage offset provides inherent active voltage positioning (AVP) for ripple reduction. Circuit simulations in a 65nm technology show more than 90% current efficiency for 100X load current variation, while it can operate for an input voltage range of 0.6V – 1.2V

A Wide Band Adaptive All Digital Phase Locked Loop With Self Jitter Measurement And Calibration

The expanding growth of mobile products and services has led to various wireless communication standards that employ different spectrum bands and protocols to provide data, voice or video communication services. Software deffned radio and cognitive radio are emerging techniques that can dynamically integrate various standards to provide seamless global coverage, including global roaming across geographical regions, and interfacing with different wireless networks. In software deffned radio and cognitive radio, one of the most critical RF blocks that need to exhibit frequency agility is the phase lock loop (PLL) frequency synthesizer. In order to access various standards, the frequency synthesizer needs to have wide frequency tuning range, fast tuning speed, and low phase noise and frequency spur. The traditional analog charge pump frequency synthesizer circuit design is becoming diffcult due to the continuous down-scalings of transistor feature size and power supply voltage. The goal of this project was to develop an all digital phase locked loop (ADPLL) as the alternative solution technique in RF transceivers by taking advantage of digital circuitry\u27s characteristic features of good scalability, robustness against process variation and high noise margin. The targeted frequency bands for our ADPLL design included 880MHz-960MHz, 1.92GHz-2.17GHz, 2.3GHz-2.7GHz, 3.3GHz-3.8GHz and 5.15GHz-5.85GHz that are used by wireless communication standards such as GSM, UMTS, bluetooth, WiMAX and Wi-Fi etc. This project started with the system level model development for characterizing ADPLL phase noise, fractional spur and locking speed. Then an on-chip jitter detector and parameter adapter was designed for ADPLL to perform self-tuning and self-calibration to accomplish high frequency purity and fast frequency locking in each frequency band. A novel wide band DCO is presented for multi-band wireless application. The proposed wide band adaptive ADPLL was implemented in the IBM 0.13µm CMOS technology. The phase noise performance, the frequency locking speed as well as the tuning range of the digitally controlled oscillator was assessed and agrees well with the theoretical analysis

Analysis and Design of Energy Efficient Frequency Synthesizers for Wireless Integrated Systems

Advances in ultra-low power (ULP) circuit technologies are expanding the IoT applications in our daily life. However, wireless connectivity, small form factor and long lifetime are still the key constraints for many envisioned wearable, implantable and maintenance-free monitoring systems to be practically deployed at a large scale. The frequency synthesizer is one of the most power hungry and complicated blocks that not only constraints RF performance but also offers subtle scalability with power as well. Furthermore, the only indispensable off-chip component, the crystal oscillator, is also associated with the frequency synthesizer as a reference. This thesis addresses the above issues by analyzing how phase noise of the LO affect the frequency modulated wireless system in different aspects and how different noise sources in the PLL affect the performance. Several chip prototypes have been demonstrated including: 1) An ULP FSK transmitter with SAR assisted FLL; 2) A ring oscillator based all-digital BLE transmitter utilizing a quarter RF frequency LO and 4X frequency multiplier; and 3) An XO-less BLE transmitter with an RF reference recovery receiver. The first 2 designs deal with noise sources in the PLL loop for ultimate power and cost reduction, while the third design deals with the reference noise outside the PLL and explores a way to replace the XO in ULP wireless edge nodes. And at last, a comprehensive PN theory is proposed as the design guideline.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/153420/1/chenxing_1.pd

A digital multiplying delay locked loop for high frequency clock generation

As Moore’s Law continues to give rise to ever shrinking channel lengths, circuits are becoming more digital and ever increasingly faster. Generating high frequency clocks in such scaled processes is becoming a tough challenge. Digital phase locked loops (DPLLs) are being explored as an alternative to conventional analog PLLs but suffer from issues such as low bandwidth and higher quantization noise. A digital multiplying delay locked loop (DMDLL) is proposed which aims at leveraging the benefit of high bandwidth of DLL while at the same time achieving the frequency multiplication property of PLL. It also offers the benefits of easier portability across process and occupies lesser area. The proposed DMDLL uses a simple flip-flop as 1-bit TDC (Time Digital Converter) for Phase Detector (PD). A digital accumulator acts as integrator for loop filter while a Δ-Σ DAC in combination with a VCO acts like a DCO. A carefully designed select logic in conjunction with a MUX achieves frequency multiplication. The proposed digital MDLL is taped out in 130nm process and tested to obtain 1.4GHz output frequency with 1.6ps RMS jitter, 17ps peak-to-peak jitter and -50dbC/Hz reference spurs

A Low Voltage Delta-Sigma Fractional Frequency Divider for Multi-band WSN Frequency Synthesizers

A 1 V low voltage delta-sigma fractional-N frequency divider for multi-band (780/868/915 MHz and 2.4 GHz) WSN frequency synthesizers is presented. The frequency divider consists of a dual-modulus prescaler, a pulse-swallow counter and a delta-sigma modulator. The high-speed and low-voltage phase-switching dual-modulus prescaler is used in the frequency divider. Low threshold voltage transistors are applied to overcome low voltage supply and forward phase-switching technique is adopted to prevent glitches. The modified delta-sigma modulator with long output sequence length and less spurs is adopted to minimize the fractional spurs. The frequency divider is designed in 0.18 mm TSMC RF CMOS technology under 1 V supply instead of the standard 1.8 V supply. The total chip area is 1190 mm 485 mm including I/O pads. The post simulation results show the frequency divider operates normally over a wide range of 1.3-5.0 GHz and the core circuit (without test buffers) consumes 2.3 mW

Performance enhancement techniques for low power digital phase locked loops

Desire for low-power, high performance computing has been at core of the symbiotic union between digital circuits and CMOS scaling. While digital circuit performance improves with device scaling, analog circuits have not gained these benefits. As a result, it has become necessary to leverage increased digital circuit performance to mitigate analog circuit deficiencies in nanometer scale CMOS in order to realize world class analog solutions. In this thesis, both circuit and system enhancement techniques to improve performance of clock generators are discussed. The following techniques were developed: (1) A digital PLL that employs an adaptive and highly efficient way to cancel the effect of supply noise, (2) a supply regulated DPLL that uses low power regulator and improves supply noise rejection, (3) a digital multiplying DLL that obviates the need for high-resolution TDC while achieving sub-picosecond jitter and excellent supply noise immunity, and (4) a high resolution TDC based on a switched ring oscillator, are presented. Measured results obtained from the prototype chips are presented to illustrate the proposed design techniques

Towards Very Large Scale Analog (VLSA): Synthesizable Frequency Generation Circuits.

Driven by advancement in integrated circuit design and fabrication technologies, electronic systems have become ubiquitous. This has been enabled powerful digital design tools that continue to shrink the design cost, time-to-market, and the size of digital circuits. Similarly, the manufacturing cost has been constantly declining for the last four decades due to CMOS scaling. However, analog systems have struggled to keep up with the unprecedented scaling of digital circuits. Even today, the majority of the analog circuit blocks are custom designed, do not scale well, and require long design cycles. This thesis analyzes the factors responsible for the slow scaling of analog blocks, and presents a new design methodology that bridges the gap between traditional custom analog design and the modern digital design. The proposed methodology is utilized in implementation of the frequency generation circuits – traditionally considered analog systems. Prototypes covering two different applications were implemented. The first synthesized all-digital phase-locked loop was designed for 400-460 MHz MedRadio applications and was fabricated in a 65 nm CMOS process. The second prototype is an ultra-low power, near-threshold 187-500 kHz clock generator for energy harvesting/autonomous applications. Finally, a digitally-controlled oscillator frequency resolution enhancement technique is presented which allows reduction of quantization noise in ADPLLs without introducing spurs.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/109027/1/mufaisal_1.pd

Conception et réalisation de circuits de génération de fréquence en technologie FDSOI 28nm

The large-scale deployment of IoT requires the development of more efficient energy radio systems, within which the frequency generation circuit is known to be particularly energy-consuming. The objective of this thesis is firstly to develop a very low consumption frequency synthesis and secondly to demonstrate the performance of the FDSOI technology for analog and RF applications.In the first chapter are the specifications of the chosen standard -the BLE-, the specifications of the FDSOI technology and state of the art of low power radio frequency synthesizers architecture. We have chosen from this comparison the Fractional Phase Divider architecture. The second chapter presents the results of three types of system simulations of the PLL; 1 - the operation of its components and the key points to be respected for its implementation, 2 - the phase noise behavior for the definition of specifications, and 3 - the impact of architecture on the generation of spurious. This study allowed us to set the specifications of VCROs developed in the next chapter. The third chapter is dedicated to the design, implementation and testing of four topologies of VCROs and a test circuit in FDSOI 28nm technology. The first measurement results are encouraging but they need to be complemented by an integrated fractional PLL measurement. Indeed, the sensitivity of the circuits to the supply voltage (pushing of about 5 GHz/V) made measurements of phase noise very delicate. The measured consumption is less than 0.8 mA and the surface of the circuits is of the order of 600 µm².In the fourth and final chapter we present the implementation at circuit-level of a phase synchronization PLL.Le déploiement à grande échelle de l’internet des objets nécessite le développement de systèmes de radiocommunication plus économes en énergie, dont le circuit de génération de fréquences est connu pour être particulièrement énergivore. L’objectif de ce travail de thèse est donc d’une part de développer une synthèse de fréquences très faible consommation et d’autre part de démontrer les performances de la technologie FDSOI pour des applications analogiques et radiofréquences. Dans le premier chapitre sont présentées les spécifications du standard choisi -le BLE-, les spécificités de la technologie FDSOI et l'état de l’art des architectures de transmetteurs radiofréquences à faible consommation. Nous avons retenue de cette comparaison l'architecture à division par phases. Le deuxième chapitre présente les résultats de trois types de modélisation système de l’architecture ; 1 - le fonctionnement de ses composants et les points clés à respecter pour son implémentation, 2 - le comportement en bruit de phase pour la définition des spécifications, et 3 - l’impact de l’architecture sur la génération de raies spectrales parasites. Cette étude nous a permis de fixer le cahier des charges du VCRO développé au chapitre suivant. Le troisième chapitre est consacré à la conception, la réalisation et le test de 4 topologies de VCROs en technologie FDSOI 28nm et d'un circuit de test. Les premiers résultats de mesure sont encourageants mais nécessitent d’être complétés par des mesures avec PLL fractionnaire intégrée. En effet, la sensibilité des circuits à la tension d’alimentation (pushing de l’ordre de 5 GHz/V) a rendu les mesures du bruit de phase très délicates

On-Chip Analog Circuit Design Using Built-In Self-Test and an Integrated Multi-Dimensional Optimization Platform

Nowadays, the rapid development of system-on-chip (SoC) market introduces tremendous complexity into the integrated circuit (IC) design. Meanwhile, the IC fabrication process is scaling down to allow higher density of integration but makes the chips more sensitive to the process-voltage-temperature (PVT) variations. A successful IC product not only imposes great pressure on the IC designers, who have to handle wider variations and enforce more design margins, but also challenges the test procedure, leading to more check points and longer test time. To relax the designers’ burden and reduce the cost of testing, it is valuable to make the IC chips able to test and tune itself to some extent. In this dissertation, a fully integrated in-situ design validation and optimization (VO) hardware for analog circuits is proposed. It implements in-situ built-in self-test (BIST) techniques for analog circuits. Based on the data collected from BIST, the error between the measured and the desired performance of the target circuit is evaluated using a cost function. A digital multi-dimensional optimization engine is implemented to adaptively adjust the analog circuit parameters, seeking the minimum value of the cost function and achieving the desired performance. To verify this concept, study cases of a 2nd/4th active-RC band-pass filter (BPF) and a 2nd order Gm-C BPF, as well as all BIST and optimization blocks, are adopted on-chip. Apart from the VO system, several improved BIST techniques are also proposed in this dissertation. A single-tone sinusoidal waveform generator based on a finite-impulse-response (FIR) architecture, which utilizes an optimization algorithm to enhance its spur free dynamic range (SFDR), is proposed. It achieves an SFDR of 59 to 70 dBc from 150 to 850 MHz after the optimization procedure. A low-distortion current-steering two-tone sinusoidal signal synthesizer based on a mixing-FIR architecture is also proposed. The two-tone synthesizer extends the FIR architecture to two stages and implements an up-conversion mixer to generate the two tones, achieving better than -68 dBc IM3 below 480 MHz LO frequency without calibration. Moreover, an on-chip RF receiver linearity BIST methodology for continuous and discrete-time hybrid baseband chain is proposed. The proposed receiver chain implements a charge-domain FIR filter to notch the two excitation signals but expose the third order intermodulation (IM3) tones. It simplifies the linearity measurement procedure–using a power detector is enough to analyze the receiver’s linearity. Finally, a low cost fully digital built-in analog tester for linear-time-invariant (LTI) analog blocks is proposed. It adopts a time-to-digital converter (TDC) to measure the delays corresponded to a ramp excitation signal and is able to estimate the pole or zero locations of a low-pass LTI system

Belle II Technical Design Report

The Belle detector at the KEKB electron-positron collider has collected almost 1 billion Y(4S) events in its decade of operation. Super-KEKB, an upgrade of KEKB is under construction, to increase the luminosity by two orders of magnitude during a three-year shutdown, with an ultimate goal of 8E35 /cm^2 /s luminosity. To exploit the increased luminosity, an upgrade of the Belle detector has been proposed. A new international collaboration Belle-II, is being formed. The Technical Design Report presents physics motivation, basic methods of the accelerator upgrade, as well as key improvements of the detector.Comment: Edited by: Z. Dole\v{z}al and S. Un