Measurements of static and dynamic displacement from visual monitoring of the Humber Bridge

Author's manuscript version. The final published version is available from the publisher via doi:10.1016/0141-0296(93)90054-8. Copyright © 1993 Published by Elsevier Ltd.A visual tracking system has been employed in the measurement of deck displacements at the centre of the 1410 m span of the Humber Bridge in the UK. The transputer-based system was developed for applications such as the monitoring or testing of large physical structures, where the actual displacements may not easily be otherwise determined. The system employs parallel processing techniques to track predictively the motion of multiple, independent objects at video frame rate. Results obtained using the system in a monitoring programme of the bridge are presented and discussed. © 1993

Earth imaging with microsatellites: An investigation, design, implementation and in-orbit demonstration of electronic imaging systems for earth observation on-board low-cost microsatellites.

This research programme has studied the possibilities and difficulties of using 50 kg microsatellites to perform remote imaging of the Earth. The design constraints of these missions are quite different to those encountered in larger, conventional spacecraft. While the main attractions of microsatellites are low cost and fast response times, they present the following key limitations: Payload mass under 5 kg, Continuous payload power under 5 Watts, peak power up to 15 Watts, Narrow communications bandwidths (9.6 / 38.4 kbps), Attitude control to within 5°, No moving mechanics. The most significant factor is the limited attitude stability. Without sub-degree attitude control, conventional scanning imaging systems cannot preserve scene geometry, and are therefore poorly suited to current microsatellite capabilities. The foremost conclusion of this thesis is that electronic cameras, which capture entire scenes in a single operation, must be used to overcome the effects of the satellite's motion. The potential applications of electronic cameras, including microsatellite remote sensing, have erupted with the recent availability of high sensitivity field-array CCD (charge-coupled device) image sensors. The research programme has established suitable techniques and architectures necessary for CCD sensors, cameras and entire imaging systems to fulfil scientific/commercial remote sensing despite the difficult conditions on microsatellites. The author has refined these theories by designing, building and exploiting in-orbit five generations of electronic cameras. The major objective of meteorological scale imaging was conclusively demonstrated by the Earth imaging camera flown on the UoSAT-5 spacecraft in 1991. Improved cameras have since been carried by the KITSAT-1 (1992) and PoSAT-1 (1993) microsatellites. PoSAT-1 also flies a medium resolution camera (200 metres) which (despite complete success) has highlighted certain limitations of microsatellites for high resolution remote sensing. A reworked, and extensively modularised, design has been developed for the four camera systems deployed on the FASat-Alfa mission (1995). Based on the success of these missions, this thesis presents many recommendations for the design of microsatellite imaging systems. The novelty of this research programme has been the principle of designing practical camera systems to fit on an existing, highly restrictive, satellite platform, rather than conceiving a fictitious small satellite to support a high performance scanning imager. This pragmatic approach has resulted in the first incontestable demonstrations of the feasibility of remote sensing of the Earth from inexpensive microsatellites

Aspects of an open architecture robot controller and its integration with a stereo vision sensor.

The work presented in this thesis attempts to improve the performance of industrial robot systems in a flexible manufacturing environment by addressing a number of issues related to external sensory feedback and sensor integration, robot kinematic positioning accuracy, and robot dynamic control performance. To provide a powerful control algorithm environment and the support for external sensor integration, a transputer based open architecture robot controller is developed. It features high computational power, user accessibility at various robot control levels and external sensor integration capability. Additionally, an on-line trajectory adaptation scheme is devised and implemented in the open architecture robot controller, enabling a real-time trajectory alteration of robot motion to be achieved in response to external sensory feedback. An in depth discussion is presented on integrating a stereo vision sensor with the robot controller to perform external sensor guided robot operations. Key issues for such a vision based robot system are precise synchronisation between the vision system and the robot controller, and correct target position prediction to counteract the inherent time delay in image processing. These were successfully addressed in a demonstrator system based on a Puma robot. Efforts have also been made to improve the Puma robot kinematic and dynamic performance. A simple, effective, on-line algorithm is developed for solving the inverse kinematics problem of a calibrated industrial robot to improve robot positioning accuracy. On the dynamic control aspect, a robust adaptive robot tracking control algorithm is derived that has an improved performance compared to a conventional PID controller as well as exhibiting relatively modest computational complexity. Experiments have been carried out to validate the open architecture robot controller and demonstrate the performance of the inverse kinematics algorithm, the adaptive servo control algorithm, and the on-line trajectory generation. By integrating the open architecture robot controller with a stereo vision sensor system, robot visual guidance has been achieved with experimental results showing that the integrated system is capable of detecting, tracking and intercepting random objects moving in 3D trajectory at a velocity up to 40mm/s

A graph theoretic approach to transputer network design for computer vision

The work in this thesis is concerned with parallel architectures based on the Inmos transputer-type processors and parallelisation of some computer vision tasks chosen from low to high level. The transputer is a microprocessor with a micro-programmed scheduler and four serial communication links. It directly supports parallel processing since several transputers can be connected through their links to co-operate on solving a problem. Also several processes can be run on the same transputer. A major issue in parallel processing is the communication overhead introduced by parallelising a given task. This overhead is not present in sequential processing and must be curbed if the implementation of a task on a parallel machine is to be successful. The interconnection network underlying the architecture of a parallel computer is therefore of the utmost importance. Computer Vision consists of a hierarchy of tasks ranging from low-level operations dealing with large amounts of relatively simple data to high level operations handling increasingly complex structures. In this work a novel edge detector based on adaptive filtering and an edge detector operating on colour images are presented and implemented on a number of transputers. These parallel implementations together with implementations of vector quantisation, Fourier descriptors for shape discrimination, the Hough transform and the Maximum clique algorithm, offer a notable performance increase when compared with sequential implementations. However, every algorithm required the design of a specific network of transputers to take advantage of the parallelism and data dependencies inherent in each. Consequently, attention is focused on the topology of interconnection networks. In particular, the communication requirements of computer vision algorithms as identified by the various computer vision tasks are analysed. These requirements together with graph theoretical considerations are then used to suggest a topology for large transputer networks. The latter is based on sub-graphs, with proven performance when used to implement interconnection networks, combined to form an architecture with improved performance. This architecture consists of a fixed structure supplemented with a dynamically reconfigured network. After describing this topology, a routing algorithm that conveys messages along shortest paths in the network is given and implemented. And finally, some practical issues in the use of transputers are considered and solutions proposed

Real-time sound synthesis on a multi-processor platform

Real-time sound synthesis means that the calculation and output of each sound sample for a channel of audio information must be completed within a sample period. At a broadcasting standard, a sampling rate of 32,000 Hz, the maximum period available is 31.25 μsec. Such requirements demand a large amount of data processing power. An effective solution for this problem is a multi-processor platform; a parallel and distributed processing system. The suitability of the MIDI [Music Instrument Digital Interface] standard, published in 1983, as a controller for real-time applications is examined. Many musicians have expressed doubts on the decade old standard's ability for real-time performance. These have been investigated by measuring timing in various musical gestures, and by comparing these with the subjective characteristics of human perception. An implementation and its optimisation of real-time additive synthesis programs on a multi-transputer network are described. A prototype 81-polyphonic-note- organ configuration was implemented. By devising and deploying monitoring processes, the network's performance was measured and enhanced, leading to an efficient usage; the 88-note configuration. Since 88 simultaneous notes are rarely necessary in most performances, a scheduling program for dynamic note allocation was then introduced to achieve further efficiency gains. Considering calculation redundancies still further, a multi-sampling rate approach was applied as a further step to achieve an optimal performance. The theories underlining sound granulation, as a means of constructing complex sounds from grains, and the real-time implementation of this technique are outlined. The idea of sound granulation is quite similar to the quantum-wave theory, "acoustic quanta". Despite the conceptual simplicity, the signal processing requirements set tough demands, providing a challenge for this audio synthesis engine. Three issues arising from the results of the implementations above are discussed; the efficiency of the applications implemented, provisions for new processors and an optimal network architecture for sound synthesis