Integrated Distributed Amplifiers for Ultra-Wideband BiCMOS Receivers Operating at Millimeter-Wave Frequencies

Millimetre-wave technology is used for applications such as telecommunications and imaging. For both applications, the bandwidth of existing systems has to be increased to support higher data rates and finer imaging resolutions. Millimetrewave circuits with very large bandwidths are developed in this thesis. The focus is put on amplifiers and the on-chip integration of the amplifiers with antennas. Circuit prototypes, fabricated in a commercially available 130nm Silicon-Germanium (SiGe) Bipolar Complementary Metal-Oxide-Semiconductor (BiCMOS) process, validated the developed techniques. Cutting-edge performances have been achieved in the field of distributed and resonant-matched amplifiers, as well as in that of the antenna-amplifier co-integration. Examples are as follows: - A novel cascode gain-cell with three transistors was conceived. By means of transconductance peaking towards high frequencies, the losses of the synthetic line can be compensated up to higher frequencies. The properties were analytically derived and explained. Experimental demonstration validated the technique by a Traveling-Wave Amplifier (TWA) able to produce 10 dB of gain over a frequency band of 170GHz.# - Two Cascaded Single-Stage Distributed Amplifiers (CSSDAs) have been demonstrated. The first CSSDA, optimized for low power consumption, requires less than 20mW to provide 10 dB of gain over a frequency band of 130 GHz. The second amplifier was designed for high-frequency operation and works up to 250 GHz leading to a record bandwidth for distributed amplifiers in SiGe technology. - The first complete CSSDA circuit analysis as function of all key parameters was presented. The typical degradation of the CSSDA output matching towards high frequencies was analytically quantified. A balanced architecture was then introduced to retain the frequency-response advantages of CSSDAs and yet ensure matching over the frequency band of interested. A circuit prototype validated experimentally the technique. - The first traveling-wave power combiner and divider capable of operation from the MHz range up to 200 GHz were demonstrated. The circuits improved the state of the art of the maximum frequency of operation and the bandwidth by a factor of five. - A resonant-matched balanced amplifier was demonstrated with a centre frequency of 185 GHz, 10 dB of gain and a 55GHz wide –3 dB-bandwidth. The power consumption of the amplifier is 16.8mW, one of the lowest for this circuit class, while the bandwidth is the broadest reported in literature for resonant-matched amplifiers in SiGe technology

Radio-frequency integrated-circuit design for CMOS single-chip UWB systems

Low cost, a high-integrated capability, and low-power consumption are the basic requirements for ultra wide band (UWB) system design in order for the system to be adopted in various commercial electronic devices in the near future. Thus, the highly integrated transceiver is trended to be manufactured by companies using the latest silicon based complimentary metal-oxide-silicon (CMOS) processes. In this dissertation, several new structural designs are proposed, which provide solutions for some crucial RF blocks in CMOS for UWB for commercial applications. In this dissertation, there is a discussion of the development, as well as an illustration, of a fully-integrated ultra-broadband transmit/receive (T/R) switch which uses nMOS transistors with deep n-well in a standard 0.18-μm CMOS process. The new CMOS T/R switch exploits patterned-ground-shield on-chip inductors together with MOSFET’s parasitic capacitances in order to synthesize artificial transmission lines which result in low insertion loss over an extremely wide bandwidth. Within DC-10 GHz, 10-18 GHz, and 18-20 GHz, the developed CMOS T/R switch exhibits insertion loss of less than 0.7, 1.0 and 2.5 dB and isolation between 32-60 dB, 25-32 dB, and 25-27 dB, respectively. The measured 1-dB power compression point and input third-order intercept point reach as high as 26.2 and 41 dBm, respectively. Further, there is a discussion and demonstration of a tunable Carrier-based Time-gated UWB transmitter in this dissertation which uses a broadband multiplier, a novel fully integrated single pole single throw (SPST) switch designed by the CMOS process, where a tunable instantaneous bandwidth from 500 MHz to 4 GHz is exhibited by adjusting the width of the base band impulses in time domain. The SPST switch utilizes the synthetic transmission line concept and multiple reflections technique in order to realize a flat insertion loss less than 1.5 dB from 3.1 GHz to 10.6 GHz and an extremely high isolation of more than 45 dB within this frequency range. A fully integrated complementary LC voltage control oscillator (VCO), designed with a tunable buffer, operates from 4.6 GHz to 5.9 GHz. The measurement results demonstrate that the integrated VCO has a very low phase noise of –117 dBc/ Hz at 1 MHz offset. The fully integrated VCO achieves a very high figure of merit (FOM) of 183.5 using standard CMOS process while consuming 4 mA DC current

Design of low power CMOS UWB transceiver ICs

Master'sMASTER OF ENGINEERIN

High frequency of low noise amplifier architecture for WiMAX application: A review

The low noise amplifier (LNA) circuit is exceptionally imperative as it promotes and initializes general execution performance and quality of the mobile communication system. LNA's design in radio frequency (R.F.) circuit requires the trade-off numerous imperative features' including gain, noise figure (N.F.), bandwidth, stability, sensitivity, power consumption, and complexity. Improvements to the LNA's overall performance should be made to fulfil the worldwide interoperability for microwave access (WiMAX) specifications' prerequisites. The development of front-end receiver, particularly the LNA, is genuinely pivotal for long-distance communications up to 50 km for a particular system with particular requirements. The LNA architecture has recently been designed to concentrate on a single transistor, cascode, or cascade constrained in gain, bandwidth, and noise figure

Millimeter-scale RF Integrated Circuits and Antennas for Energy-efficient Wireless Sensor Nodes

Recently there has been increased demand for a millimeter-scale wireless sensor node for applications such as biomedical devices, defense, and surveillance. This form-factor is driven by a desire to be vanishingly small, injectable through a needle, or implantable through a minimally-invasive surgical procedure. Wireless communication is a necessity, but there are several challenges at the millimeter-scale wireless sensor node. One of the main challenges is external components like crystal reference and antenna become the bottleneck of realizing the mm-scale wireless sensor node device. A second challenge is power consumption of the electronics. At mm-scale, the micro-battery has limited capacity and small peak current. Moreover, the RF front-end circuits that operates at the highest frequency in the system will consume most of the power from the battery. Finally, as node volume reduces, there is a challenge of integrating the entire system together, in particular for the RF performance, because all components, including the battery and ICs, need to be placed in close proximity of the antenna. This research explores ways to implement low-power integrated circuits in an energy-constrained and volume constrained application. Three different prototypes are mainly conducted in the proposal. The first is a fully-encapsulated, autonomous, complete wireless sensor node with UWB transmitter in 10.6mm3 volume. It is the first time to demonstrate a full and stand-alone wireless sensing functionality with such a tiny integrated system. The second prototype is a low power GPS front-end receiver that supports burst-mode. A double super-heterodyne topology enables the reception of the three public GPS bands, L1, L2 and L5 simultaneously. The third prototype is an integrated rectangular slot loop antenna in a standard 0.13-μm BiCMOS technology. The antenna is efficiently designed to cover the bandwidth at 60 GHz band and easily satisfy the metal density rules and can be integrated with other circuitry in a standard process.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/143972/1/hskims_1.pd

Realization of a voltage controlled oscillator using 0.35 um sige-bicmos technology for multi-band applications

The stable growth in wireless communications market has engendered the interoperability of various standards in a single broadband frequency range from hundred MHz up to several GHz. This frequency range consists of various wireless applications such as GSM, Bluetooth and WLAN. Therefore, an agile wireless system needs smart RF front-ends for functioning properly in such a crowded spectrum. As a result, the demand for multi-standard RF transceivers which put various wireless and cordless phone standards together in one structure was increased. The demand for multi-standard RF transceivers gives a key role to reconfigurable wideband VCO operation with low-power and low-phase noise characteristics. Besides agility and intelligence, such a communication system (GSM, WLAN, Global Positioning Systems, etc. ) required meeting the requirements of several standards in a cost-effective way. This, when cost and integration are the major concerns, leads to the exploitation of Si-based technologies. In this thesis, an integrated 2.2-5.7GHz Multi-band differential LC VCO for Multi-standard Wireless Communication systems was designed utilizing 0.35μm SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78GHz, 3.22-3.53GHz, 3.48-3.91GHz and 4.528-5.7GHz) with a maximum bandwidth of 1.36GHz and a minimum bandwidth of 300MHz. The designed and simulated VCO can generate a differential output power between 0.992 dBm and -6.087 dBm with an average power consumption of 44.21mW including the buffers. The average second and third harmonics level were obtained as -37.21 dBm and -47.6 dBm, respectively. The phase noise between -110.45 and -122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between -176.48 and -181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment

Millimeter-Wave Concurrent Dual-Band Sige Bicmos Rfic Phased-Array Transmitter and Components

A concurrent dual-band phased-array transmitter (TX) and its constituent components are studied in this dissertation. The TX and components are designed for the unlicensed bands, 22–29 and 57–64 GHz, using a 0.18-μm BiCMOS technology. Various studies have been done to design the components, which are suitable for the concurrent dual-band phased-array TX. The designed and developed components in this study are an attenuator, switch, phase shifter, power amplifier and power divider. Attenuators play a key role in tailoring main beam and side-lobe patterns in a phased-array TX. To perform the function in the concurrent dual-band phased-array TX, a 22–29 and 57–64 GHz concurrent dual-band attenuator with low phase variations is designed. Signal detection paths are employed at the output of the phased-array TX to monitor the phase and amplitude deviations/errors, which are larger in the high-frequency design. The detected information enables the TX to have an accurate beam tailoring and steering. A 10–67 GHz wide-band attenuator, covering the dual bands, is designed to manipulate the amplitude of the detected signal. New design techniques for an attenuator with a wide attenuation range and improved flatness are proposed. Also, a topology of dual-function circuit, attenuation and switching, is proposed. The switching turns on and off the detection path to minimize the leakages while the path is not used. Switches are used to minimize the number of components in the phased-array transceiver. With the switches, some of the bi-directional components in the transceiver such as an attenuator, phase shifter, filter, and antenna can be shared by the TX and receiver (RX) parts. In this dissertation, a high-isolation switch with a band-pass filtering response is proposed. The band-pass filtering response suppresses the undesired harmonics and intermodulation products of the TX. Phase shifters are used in phased-array TXs to steer the direction of the beam. A 24-GHz phase shifter with low insertion loss variation is designed using a transistor-body-floating technique for our phased-array TX. The low insertion loss variation minimizes the interference in the amplitude control operation (by attenuator or variable gain amplifier) in phased-array systems. BJTs in a BiCMOS process are characterized across dc to 67 GHz. A novel characterization technique, using on-wafer calibration and EM-based de-embedding both, is proposed and its accuracy at high frequencies is verified. The characterized BJT is used in designing the amplifiers in the phased-array TX. A concurrent dual-band power amplifier (PA) centered at 24 and 60 GHz is proposed and designed for the dual-band phased-array TX. Since the PA is operating in the dual frequency bands simultaneously, significant linearity issues occur. To resolve the problems, a study to find significant intermodulation (IM) products, which increase the third intermodulation (IM3) products most, has been done. Also, an advanced simulation and measurement methodology using three fundamental tones is proposed. An 8-way power divider with dual-band frequency response of 22–29 and 57–64 GHz is designed as a constituent component of the phased-array TX

Millimeter-Wave Concurrent Dual-Band BiCMOS RFIC Transmitter for Radar and Communication Systems

This dissertation presents new circuit architectures and techniques for improving the performance of several key BiCMOS RFIC building blocks used in radar and wireless communication systems operating up to millimeter-wave frequencies, and the development of an advanced, low-cost and miniature millimeter-wave concurrent dual-band transmitter for short-range, high-resolution radar and high-rate communication systems. A new type of low-power active balun consisting of a common emitter amplifier with degenerative inductor and a common collector amplifier is proposed. The parasitic neutralization and compensation techniques are used to keep the balun well balanced at very high frequencies and across an ultra-wide bandwidth. A novel RF switch architecture with ultra-high isolation and possible gain is proposed, analyzed and demonstrated. The new RF switch architecture achieves an ultra-high isolation through implementation of a new RF leaking cancellation technique. A new class of concurrent dual-band impedance matching networks and technique for synthesizing them are presented together with a 25.5/37-GHz concurrent dual-band PA. These matching networks enable simultaneous matching of two arbitrary loads to two arbitrary sources at two different frequencies, utilizing the impedance-equivalence properties of LC networks that any LC network can be equivalent to an inductor, capacitor, open or short at different frequencies. K- and Ka-band ultra-low-leakage RF-pulse formers capable of producing very narrow RF pulses in the order of 200 ps with small rising and falling time for short-range high-resolution radar and high-data-rate communication systems are also developed. The complete transmitter exhibiting unique characteristics obtained from capabilities of producing very narrow and tunable RF pulses with extremely RF leakage and working concurrently in dual bands at 24.5 and 35 GHz was designed. Capability of generating narrow and tunable RF pulses allows the radar system to flexibly work at high and multiple range resolutions. The extremely low RF leakage allows the transmitter to share one antenna system with receiver, turn on the PA at all time, comply the transmitting spectrum requirements, increase the system dynamic range, avoid harming to other systems; hence improving system size, cost and performance. High data-rate in communication systems is achieved as the consequence of transmitting very narrow RF pulses at high rates. In addition, the dissertation demonstrates a design approach for low chip-area, cost and power consumption systems in which a single dual-band component (power amplifier) is designed to operate with two RF signals simultaneously

Advances in Integrated Circuit Design and Implementation for New Generation of Wireless Transceivers

User’s everyday outgrowing demand for high-data and high performance mobile devices pushes industry and researchers into more sophisticated systems to fulfill those expectations. Besides new modulation techniques and new system designs, significant improvement is required in the transceiver building blocks to handle higher data rates with reasonable power efficiency. In this research the challenges and solution to improve the performance of wireless communication transceivers is addressed. The building block that determines the efficiency and battery life of the entire mobile handset is the power amplifier. Modulations with large peak to average power ratio severely degrade efficiency in the conventional fixed-biased power amplifiers (PAs). To address this challenge, a novel PA is proposed with an adaptive load for the PA to improve efficiency. A nonlinearity cancellation technique is also proposed to improve linearity of the PA to satisfy the EVM and ACLR specifications. Ultra wide-band (UWB) systems are attractive due to their ability for high data rate, and low power consumption. In spite of the limitation assigned by the FCC, the coexistence of UWB and NB systems are still an unsolved challenge. One of the systems that is majorly affected by the UWB signal, is the 802.11a system (5 GHz Wi-Fi). A new analog solution is proposed to minimize the interference level caused by the impulse Radio UWB transmitter to nearby narrowband receivers. An efficient 400 Mpulse/s IR-UWB transmitter is implemented that generates an analog UWB pulse with in-band notch that covers the majority of the UWB spectrum. The challenge in receiver (RX) design is the over increasing out of blockers in applications such as cognitive and software defined radios, which are required to tolerate stronger out-of-band (OB) blockers. A novel RX is proposed with a shunt N-path high-Q filter at the LNA input to attenuate OB-blockers. To further improve the linearity, a novel baseband blocker filtering techniques is proposed. A new TIA has been designed to maintain the good linearity performance for blockers at large frequency offsets. As a result, a +22 dBm IIP3 with 3.5 dB NF is achieved. Another challenge in the RX design is the tough NF and linearity requirements for high performance systems such as carrier aggregation. To improve the NF, an extra gain stage is added after the LNA. An N-path high-Q band-pass filter is employed at the LNA output together with baseband blocker filtering technique to attenuate out-of-band blockers and improve the linearity. A noise-cancellation technique based on the frequency translation has been employed to improve the NF. As a result, a 1.8dB NF with +5 dBm IIP3 is achieved. In addition, a new approach has been proposed to reject out of band blockers in carrier aggregation scenarios. The proposed solution also provides carrier to carrier isolation compared to typical solution for carrier aggregation