System-level design and RF front-end implementation for a 3-10ghz multiband-ofdm ultrawideband receiver and built-in testing techniques for analog and rf integrated circuits

This work consists of two main parts: a) Design of a 3-10GHz UltraWideBand (UWB) Receiver and b) Built-In Testing Techniques (BIT) for Analog and RF circuits. The MultiBand OFDM (MB-OFDM) proposal for UWB communications has received significant attention for the implementation of very high data rate (up to 480Mb/s) wireless devices. A wideband LNA with a tunable notch filter, a downconversion quadrature mixer, and the overall radio system-level design are proposed for an 11-band 3.4-10.3GHz direct conversion receiver for MB-OFDM UWB implemented in a 0.25mm BiCMOS process. The packaged IC includes an RF front-end with interference rejection at 5.25GHz, a frequency synthesizer generating 11 carrier tones in quadrature with fast hopping, and a linear phase baseband section with 42dB of gain programmability. The receiver IC mounted on a FR-4 substrate provides a maximum gain of 67-78dB and NF of 5-10dB across all bands while consuming 114mA from a 2.5V supply. Two BIT techniques for analog and RF circuits are developed. The goal is to reduce the test cost by reducing the use of analog instrumentation. An integrated frequency response characterization system with a digital interface is proposed to test the magnitude and phase responses at different nodes of an analog circuit. A complete prototype in CMOS 0.35mm technology employs only 0.3mm2 of area. Its operation is demonstrated by performing frequency response measurements in a range of 1 to 130MHz on 2 analog filters integrated on the same chip. A very compact CMOS RF RMS Detector and a methodology for its use in the built-in measurement of the gain and 1dB compression point of RF circuits are proposed to address the problem of on-chip testing at RF frequencies. The proposed device generates a DC voltage proportional to the RMS voltage amplitude of an RF signal. A design in CMOS 0.35mm technology presents and input capacitance <15fF and occupies and area of 0.03mm2. The application of these two techniques in combination with a loop-back test architecture significantly enhances the testability of a wireless transceiver system

Silicon Germanium BiCMOS Integrated Circuits for Scalable Cryogenic Sensing Applications

This dissertation is focused on an investigation of BiCMOS cryogenic low noise amplifiers (LNAs) based on Silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) for simultaneous low noise and low power design and also taking advantage of CMOS circuitry for adding flexibility to the LNA design. Cryogenic LNAs\u27 scalability challenges are discussed and addressed in the dissertation. To achieve that, first, HBTs of three state-of-the-art technologies are characterized and modeled at cryogenic temperature. It is shown that SiGe HBT provides a promising compromise of noise temperature, power consumption, and bandwidth. Moreover, a scalable on-chip approach is proposed and verified for biasing of SiGe HBTs based LNAs. Finally, the first cryogenic re-configurable LNA is designed, implemented, and measured

Unattended network operations technology assessment study. Technical support for defining advanced satellite systems concepts

The results are summarized of an unattended network operations technology assessment study for the Space Exploration Initiative (SEI). The scope of the work included: (1) identified possible enhancements due to the proposed Mars communications network; (2) identified network operations on Mars; (3) performed a technology assessment of possible supporting technologies based on current and future approaches to network operations; and (4) developed a plan for the testing and development of these technologies. The most important results obtained are as follows: (1) addition of a third Mars Relay Satellite (MRS) and MRS cross link capabilities will enhance the network's fault tolerance capabilities through improved connectivity; (2) network functions can be divided into the six basic ISO network functional groups; (3) distributed artificial intelligence technologies will augment more traditional network management technologies to form the technological infrastructure of a virtually unattended network; and (4) a great effort is required to bring the current network technology levels for manned space communications up to the level needed for an automated fault tolerance Mars communications network

Inside all-optical networks

Imagine a world where lightning speed Internet is as common as telephones today. Imagine when light, the fastest moving thing in the universe, is the signal-carrying transport medium. Imagine when bandwidth no more remains a constraint for any application. Imagine when imagination is the only limit! This all can be made possible with only one technology and that is optical communication. Optical networks have thus far provided a realization to a greater extent to the unlimited bandwidth dreams of this era, but as the demands are increasing, the electro-optic conversions seem to become bottlenecks in blended optical networks. The only answer to this is a complete migration to `All-Optical Networks\u27 (AONs) which promise an end-to-end optical transmission. This thesis will investigate various aspects of all-optical networks and prove that AONs perform better than currently existing electro-optical networks. In today\u27s\u27 electro-optical networks, routing and switching is performed in electronic domain. Performance analysis of electro-optical and all-optical networks would include node utilization, link utilization and percentage of traffic routed. It will be shown through Opnet Transport Planner simulations that AONs work better under various traffic conditions. The coming decade will see a great boom in demands on telecommunications networks. The development in bandwidth-hungry applications like real-time video transmission, telemedicine, distance learning and video on demand require both an unlimited amount of bandwidth and dependable QoS. It is well understood that electrically switched networks and copper cables will not be able to meet the future network demands effectively. The world has already agreed to move towards optical communication techniques through the introduction of fiber in access parts of the networks replacing copper. Now the race is to bring optics in higher layers of OSI reference model. Optical communication is on the horizon, and new discoveries are still underway to add to the value of available bandwidth through this technology. My research thesis will primarily focus on the design, architecture and network properties of AONs and challenges being faced by AONs in commercial deployment. Optical components required in AONs will be explored. A comparison between AONs and electro-optical networks will also be shown through optical transport planner simulations

NASA Tech Briefs, December 2012

The topics include: Pattern Generator for Bench Test of Digital Boards; 670-GHz Down- and Up-Converting HEMT-Based Mixers; Lidar Electro-Optic Beam Switch with a Liquid Crystal Variable Retarder; Feedback Augmented Sub-Ranging (FASR) Quantizer; Real-Time Distributed Embedded Oscillator Operating Frequency Monitoring; Software Modules for the Proximity-1 Space Link Interleaved Time Synchronization (PITS) Protocol; Description and User Instructions for the Quaternion to Orbit v3 Software; AdapChem; Mars Relay Lander and Orbiter Overflight Profile Estimation; Extended Testability Analysis Tool; Interactive 3D Mars Visualization; Rapid Diagnostics of Onboard Sequences; MER Telemetry Processor; pyam: Python Implementation of YaM; Process for Patterning Indium for Bump Bonding; Archway for Radiation and Micrometeorite Occurrence Resistance; 4D Light Field Imaging System Using Programmable Aperture; Device and Container for Reheating and Sterilization; Radio Frequency Plasma Discharge Lamps for Use as Stable Calibration Light Sources; Membrane Shell Reflector Segment Antenna; High-Speed Transport of Fluid Drops and Solid Particles via Surface Acoustic Waves; Compact Autonomous Hemispheric Vision System; A Distributive, Non-Destructive, Real-Time Approach to Snowpack Monitoring; Wideband Single-Crystal Transducer for Bone Characterization; Numerical Simulation of Rocket Exhaust Interaction With Lunar Soil; Motion Imagery and Robotics Application (MIRA): Standards-Based Robotics; Particle Filtering for Model-Based Anomaly Detection in Sensor Networks; Ka-band Digitally Beamformed Airborne Radar Using SweepSAR Technique; Composite With In Situ Plenums; Multi-Beam Approach for Accelerating Alignment and Calibration of HyspIRI-Like Imaging Spectrometers; JWST Lifting System; Next-Generation Tumbleweed Rover; Pneumatic System for Concentration of Micrometer-Size Lunar Soil

Contributing to Second Harmonic Manipulated Continuum Mode Power Amplifiers and On-Chip Flux Concentrators

The current cellular network consumes a staggering 100 TWh of energy every year. In the coming years, millions of devices will be added to the existing network to realize the Internet of Things (IoT), further increasing its power consumption. An RF power amplifier typically consumes a large proportion of the DC power in a wireless transceiver, improving its efficiency has the largest impact on the overall system. Additionally, amplifiers need to demonstrate high linearity and bandwidth to adhere to constraints imposed by wireless standards and to reduce the number of amplifiers required as an amplifier with a broader bandwidth can potentially replace several narrowband amplifiers. A typical approach to improve efficiency is to present an appropriate load at the harmonics generated by the transistor. Recently proposed continuous modes based on harmonic manipulation, such as class B/J continuum, continuous class F (CCF) and continuous class F-1 (CCF-1), have shown the capability of achieving counteracting requirements viz., high efficiency, high linearity, and broad bandwidth (with a fractional bandwidth greater than 30%). In these classes of amplifiers, the second harmonic is manipulated by placing a reactive second harmonic load and the reactive component of the fundamental load is adjusted while keeping a fixed resistive component of the fundamental load. The first contribution of this work is to investigate the reason for amplifiers designed in classes B/J continuum and CCF to achieve high efficiency at back-off and 1dB compression. In this thesis, we demonstrate that the variation of the phase of the current through the non-linear intrinsic capacitances due to the variation of the phase in the continuum of drain voltage waveforms in Class B/J/J* continuum leads to either a reduction or enhancement of intrinsic drain current. Consequently, a subset of voltage waveforms of the class B/J/J* continuum can be used to design amplifiers with higher P1dB, and efficiency at P1dB than in Class B. A simple choice of this subset is demonstrated with a 2.6GHz Class B/J/J* amplifier, achieving a P1dB of 38.1dBm and PAE at P1dB of 54.7%, the highest output power and efficiency at P1dB amongst narrowband linear amplifiers using the CGH40010 reported to date, at a comparable peak PAE of 72%. Secondly, we propose a new formulation for high-efficiency modes of power amplifiers in which both the in-phase and out-of-phase components of the second harmonic of the current are varied, in addition to the second harmonic component of the voltage. A reduction of the in-phase component of the second harmonic of current allows reduction of the phase difference between the voltage and current waveforms, thereby increasing the power factor and efficiency. Our proposed waveforms offer a continuous design space between class B/J continuum and continuous F-1 achieving an efficiency of up to 91% in theory, but over a wider set of load impedances than continuous class F-1. These waveforms require a short at third and higher harmonic impedances, which are easier to achieve at a higher frequency. The load impedances at the second harmonic are reactive and can be of any value between -j∞ and j∞, easing the amplifier design. A trade-off between linearity and efficiency exists in the newly proposed broadband design space, but we demonstrate inherent broadband capability. The fabricated narrowband amplifier using a GaN HEMT CGH40010F demonstrates 75.9% PAE and 42.2 dBm output power at 2.6 GHz, demonstrating a comparable frequency weighted efficiency for this device to that reported in the literature. IoT devices may be deployed in critical applications such as radar or 5G transceivers of an autonomous vehicle and hence need to operate free of failure. Monitoring the drain current of the RF GaN MMIC would allow to optimize the device performance and protect it from surges in its supply current. Galvanic current sensors rely on the magnetic field generated by the current as a non-invasive method of current sensing. In this thesis, our third major contribution is a planar on-chip magnetic flux concentrator, is enhance the magnetic field at the current sensor, thereby improving the current detection capability of a current sensor. Our layout utilizes a discontinuity in a magnetic via, resulting in penetration of the magnetic field into the substrate. The proposed concentrator has a magnetic gain x1.8 in comparison to air. The permeability of the magnetic core required is 500, much lower than that reported in off-chip concentrators, resulting in a significant easing of the specifications of the material properties of the core. Additionally, we explore a novel three-dimensional spiral-shaped magnetic flux concentrator. It is predicted via simulations that this geometry becomes a necessity to enhance the magnetic field for increased form factor as the magnetic field from a single planar concentrator deteriorates as its size increases

Architecture and Advanced Electronics Pathways Toward Highly Adaptive Energy- Efficient Computing

With the explosion of the number of compute nodes, the bottleneck of future computing systems lies in the network architecture connecting the nodes. Addressing the bottleneck requires replacing current backplane-based network topologies. We propose to revolutionize computing electronics by realizing embedded optical waveguides for onboard networking and wireless chip-to-chip links at 200-GHz carrier frequency connecting neighboring boards in a rack. The control of novel rate-adaptive optical and mm-wave transceivers needs tight interlinking with the system software for runtime resource management

Towards an Optimal Photonic Network: Optimising Performance, Cost and Flexibility

This thesis investigates optical fibre transmission system technologies, and their impact on network architectures with the objective of lowering unit cost ($/Gb/s/km) of data transmission in long-haul, and ultra long-haul dense wavelength division multiplexing (DWDM) photonic networks. The importance of this work is driven by the exponential growth in Internet traffic of around 40% p.a., and economic pressures constraining network operators’ ability to invest in their networks. Optical transport networks must therefore be designed to meet future bandwidth demands of end users, with optimum performance, cost and flexibility. Dynamic gain equalisers (DGEs) are a key sub-system of ultra long-haul networks, enabling increased un-regenerated transmission reach and elimination of expensive optical-electrical-optical (OEO) regeneration. A theoretical framework was developed integrating models of wideband power variation, together with narrowband nonlinear propagation simulations using the split-step Fourier method. The optimum spacing of the also costly DGEs was determined for a 3,000km network field deployment. Optimum power pre-emphasis profiles were predicted and compared with simple linear calculations, showing <0.7dB performance penalty using the much faster, simplified method. Optical dispersion management schemes were studied, with optical dispersion compensating fibre placed after every other span resulting in 6% cost reduction and little performance degradation compared to compensation after every span. A techno-economic comparison of optical and electronic dispersion compensation (EDC) strategies showed 25% cost reduction using EDC. Tolerance to fibre nonlinearities is reduced compared to optical compensation; splitting the EDC function equally between transmitter and receiver optimises performance. Economic benefits of a single flexible, multi-reach DWDM system were investigated showing almost 20% cost savings compared to separate long-haul and ultra long-haul systems. Finally, the techno-economic benefits of optical bypass in meshed networks were analysed for increasing levels of optical transparency: from OEO regenerated to multi-degree reconfigurable optical add-drop multiplexers (MD-ROADMs), enabling up to 46% cost saving

High speed all optical networks

An inherent problem of conventional point-to-point wide area network (WAN) architectures is that they cannot translate optical transmission bandwidth into comparable user available throughput due to the limiting electronic processing speed of the switching nodes. The first solution to wavelength division multiplexing (WDM) based WAN networks that overcomes this limitation is presented. The proposed Lightnet architecture takes into account the idiosyncrasies of WDM switching/transmission leading to an efficient and pragmatic solution. The Lightnet architecture trades the ample WDM bandwidth for a reduction in the number of processing stages and a simplification of each switching stage, leading to drastically increased effective network throughputs. The principle of the Lightnet architecture is the construction and use of virtual topology networks, embedded in the original network in the wavelength domain. For this construction Lightnets utilize the new concept of lightpaths which constitute the links of the virtual topology. Lightpaths are all-optical, multihop, paths in the network that allow data to be switched through intermediate nodes using high throughput passive optical switches. The use of the virtual topologies and the associated switching design introduce a number of new ideas, which are discussed in detail