ASDTIC control and standardized interface circuits applied to buck, parallel and buck-boost dc to dc power converters

Versatile standardized pulse modulation nondissipatively regulated control signal processing circuits were applied to three most commonly used dc to dc power converter configurations: (1) the series switching buck-regulator, (2) the pulse modulated parallel inverter, and (3) the buck-boost converter. The unique control concept and the commonality of control functions for all switching regulators have resulted in improved static and dynamic performance and control circuit standardization. New power-circuit technology was also applied to enhance reliability and to achieve optimum weight and efficiency

Nuclear electric propulsion reactor control systems status

The thermionic reactor control system design studies conducted over the past several years for a nuclear electric propulsion system are described and summarized. The relevant reactor control system studies are discussed in qualitative terms, pointing out the significant advantages and disadvantages including the impact that the various control systems would have on the nuclear electric propulsion system design. A recommendation for the reference control system is made, and a program for future work leading to an engineering model is described

Maximum power point tracking converter based on the open-circuit voltage method for thermoelectric generators

Thermoelectric generators (TEGs) convert heat energy into electricity in a quantity dependant on the temperature difference across them and the electrical load applied. It is critical to track the optimum electrical operating point through the use of power electronic converters controlled by a Maximum Power Point Tracking (MPPT) algorithm. The MPPT method based on the opencircuit voltage is arguably the most suitable for the linear electrical characteristic of TEGs. This paper presents an innovative way to perform the open-circuit voltage measure during the pseudo-normal operation of the interfacing power electronic converter. The proposed MPPT technique is supported by theoretical analysis and used to control a synchronous buck-boost converter. The prototype MPPT converter is controlled by an inexpensive microcontroller, and a lead-acid battery is used to accumulate the harvested energy. Experimental results using commercial TEG devices prove that the converter accurately tracks the maximum power point during thermal transients. Precise measurements in steady state show that the converter finds the maximum power point with a tracking efficiency of 99.85%

Electrical performance characteristics of high power converters for space power applications

The first goal of this project was to investigate various converters that would be suitable for processing electric power derived from a nuclear reactor. The implementation is indicated of a 20 kHz system that includes a source converter, a ballast converter, and a fixed frequency converter for generating the 20 kHz output. This system can be converted to dc simply by removing the fixed frequency converter. This present study emphasized the design and testing of the source and ballast converters. A push-pull current-fed (PPCF) design was selected for the source converter, and a 2.7 kW version of this was implemented using three 900 watt modules in parallel. The characteristic equation for two converters in parallel was derived, but this analysis did not yield any experimental methods for measuring relative stability. The three source modules were first tested individually and then in parallel as a 2.7 kW system. All tests proved to be satisfactory; the system was stable; efficiency and regulation were acceptable; and the system was fault tolerant. The design of a ballast-load converter, which was operated as a shunt regulator, was investigated. The proposed power circuit is suitable for use with BJTs because proportional base drive is easily implemented. A control circuit which minimizes switching frequency ripple and automatically bypasses a faulty shunt section was developed. A nonlinear state-space-averaged model of the shunt regulator was developed and shown to produce an accurate incremental (small-signal) dynamic model, even though the usual state-space-averaging assumptions were not met. The nonlinear model was also shown to be useful for large-signal dynamic simulation using PSpice

Design and Switching Performance Evaluation of a 10 kV SiC MOSFET Based Phase Leg for Medium Voltage Applications

10 kV SiC MOSFETs are promising to substantially boost the performance of future medium voltage (MV) converters, ranging from MV motor drives to fast charging stations for electric vehicles (EVs). Numerous factors influence the switching performance of 10 kV SiC MOSFETs with much faster switching speed than their Si counterparts. Thorough evaluation of their switching performance is necessary before applying them in MV converters. Particularly, the impact of parasitic capacitors in the MV converter and the freewheeling diode is investigated to understand the switching performance more comprehensively and guide the converter design based on 10 kV SiC MOSFETs.A 6.5 kV half bridge phase leg based on discrete 10 kV/20 A SiC MOSFETs is designed and fully validated to operate continuously at rated voltage with dv/dt up to 80 V/ns. Based on the phase leg, the impact of parasitic capacitors brought by the load inductor and the heatsink on the switching transients and performance of 10 kV SiC MOSFETs is investigated. Larger parasitic capacitors result in more oscillations, longer switching transients, as well as higher switching energy loss especially at low load current. As for the freewheeling diode, the body diode of 10 kV SiC MOSFETs is suitable to serve as the freewheeling diode, with negligible reverse recovery charge at various temperatures. The switching performance with and without the anti-parallel SiC junction barrier Schottky (JBS) diode is compared quantitatively. It is not recommended to add an anti-parallel diode for the 10 kV SiC MOSFET in the converter because it increases the switching loss

Transient Mitigation of DC–DC Converters for High Output Current Slew Rate Applications

published_or_final_versio

Survey on Photo-Voltaic Powered Interleaved Converter System

Renewable energy is the best solution to meet the growing demand for energy in the country. The solar energy is considered as the most promising energy by the researchers due to its abundant availability, eco-friendly nature, long lasting nature, wide range of application and above all it is a maintenance free system. The energy absorbed by the earth can satisfy 15000 times of today’s total energy demand and its hundred times more than that our conventional energy like coal and other fossil fuels. Though, there are overwhelming advantages in solar energy, It has few drawbacks as well such as its low conversion ratio, inconsistent supply of energy due to variation in the sun light, less efficiency due to ripples in the converter, time dependent and, above all, high capitation cost. These aforementioned flaws have been addressed by the researchers in order to extract maximum energy and attain hundred percentage benefits of this heavenly resource. So, this chapter presents a comprehensive investigation based on photo voltaic (PV) system requirements with the following constraints such as system efficiency, system gain, dynamic response, switching losses are investigated. The overview exhibits and identifies the requirements of a best PV power generation system

Switching Performance Evaluation, Design, and Test of a Robust 10 kV SiC MOSFET Based Phase Leg for Modular Medium Voltage Converters

10 kV SiC MOSFETs are one of the most promising power semiconductor devices for next-generation high-performance modular medium voltage (MV) converters. With extraordinary device characteristics, 10 kV SiC MOSFETs also bring a variety of challenges in the design and test of MV converters. To tackle these inherent challenges, this dissertation focuses on a robust half bridge (HB) phase leg based on 10 kV SiC MOSFETs for modular MV converters. A baseline design and test of the phase leg is established first as the foundation of the research in this dissertation. Thorough evaluation of 10 kV SiC MOSFETs’ switching performance in a phase leg is necessary before applying them in MV converters. The impact of parasitic capacitors and the freewheeling diode is investigated to understand the switching performance more extensively and guide the converter design. One non-negligible challenge is the flashover fault resulting from the premature insulation breakdown, a short circuit fault with extremely fast transients. A device model is established to analyze the behavior of 10 kV SiC MOSFETs when the fault occurs in a phase leg thoroughly. Subsequently, the gate driver and protection design considerations are summarized to achieve lower short circuit current and overvoltage and ensure the survival of the MOSFET that in ON state when the fault happens. Furthermore, it is challenging to design the overcurrent/short circuit protection with fast response and strong noise immunity under fast switching transients for 10 kV SiC MOSFETs. The noise immunity of the desaturation (desat) protection is studied quantitatively to provide design guidelines for noise immunity enhancement. Then, the protection scheme based on desat protection is developed and validated withimmunity, the strong noise immunity of the developed protection is also successfully validated. In addition, a simple test scheme is proposed and validated experimentally, in order to qualify the HB phase leg based on the 10 kV SiC MOSFET comprehensively for the modular MV converter applications. The test scheme includes the ac-dc continuous test with two phase legs in series to create the testing condition similar to what is generated in a modular MV converter, especially the high dv/dt. The test scheme can fully test the capability of the phase leg to withstand high dv/dt and its resulting noise

The application of the analog signal to discrete time interval converter to the signal conditioner power supplies

The Analog Signal to Discrete Time Interval Converter microminiaturized module was utilized to control the signal conditioner power supplies. The multi-loop control provides outstanding static and dynamic performance characteristics, exceeding those generally associated with single-loop regulators. Eight converter boards, each containing three independent dc to dc converter, were built, tested, and delivered