Receiver Front-Ends in CMOS with Ultra-Low Power Consumption

Historically, research on radio communication has focused on improving range and data rate. In the last decade, however, there has been an increasing demand for low power and low cost radios that can provide connectivity with small devices around us. They should be able to offer basic connectivity with a power consumption low enough to function extended periods of time on a single battery charge, or even energy scavenged from the surroundings. This work is focused on the design of ultra-low power receiver front-ends intended for a receiver operating in the 2.4GHz ISM band, having an active power consumption of 1mW and chip area of 1mm². Low power consumption and small size make it hard to achieve good sensitivity and tolerance to interference. This thesis starts with an introduction to the overall receiver specifications, low power radio and radio standards, front-end and LO generation architectures and building blocks, followed by the four included papers. Paper I demonstrates an inductorless front-end operating at 915MHz, including a frequency divider for quadrature LO generation. An LO generator operating at 2.4GHz is shown in Paper II, enabling a front-end operating above 2GHz. Papers III and IV contain circuits with combined front-end and LO generator operating at or above the full 2.45GHz target frequency. They use VCO and frequency divider topologies that offer efficient operation and low quadrature error. An efficient passive-mixer design with improved suppression of interference, enables an LNA-less design in Paper IV capable of operating without a SAW-filter

Design of a RF communication receiver front-end for ultra-low power and voltage applications in a FDSOI 28nm technology

The advances in the semiconductor and wireless industry have enabled the expansion of new paradigms, which have given rise to concepts like Internet of Things (IoT). Apart from qualities like size, speed or cost, the ever-increasing demand for autonomy focuses all design efforts in the minimization of power consumption. Scaling technologies and the request to reduce power consumption have pushed designers towards lower supply voltages. Despite the fact that technology scalability allows for faster transistors, radio-frequency (RF) integrated circuit (IC) design accuses the reduction of the voltage supply through frequency response degradation, which significantly deteriorates the overall performance. Analog and RF circuits in highend applications require substantial gate voltage overdrive to maintain device speed, which further complicates the design due to the reduction of voltage headroom. As a consequence, the necessity to develop circuit topologies capable to deal with low-power and low-voltage stringent constraints well suited to applications requiring long battery life and low cost emerges. This work aims to implement a low-noise amplifier and mixer stages of a radio-frequency receiver front-end working under an ultra-low power (< 100 ?W) and ultra-low voltage (< 0.8V) scenario while targeting decent overall performance. To cope with the stringent power requirements, 28nm FD-SOI technology will be used to take maximum profit of aggressive forward body bias and enhance transistor performance

Low power CMOS IC, biosensor and wireless power transfer techniques for wireless sensor network application

The emerging field of wireless sensor network (WSN) is receiving great attention due to the interest in healthcare. Traditional battery-powered devices suffer from large size, weight and secondary replacement surgery after the battery life-time which is often not desired, especially for an implantable application. Thus an energy harvesting method needs to be investigated. In addition to energy harvesting, the sensor network needs to be low power to extend the wireless power transfer distance and meet the regulation on RF power exposed to human tissue (specific absorption ratio). Also, miniature sensor integration is another challenge since most of the commercial sensors have rigid form or have a bulky size. The objective of this thesis is to provide solutions to the aforementioned challenges

Integrated Circuit and System Design for Cognitive Radio and Ultra-Low Power Applications

The ubiquitous presence of wireless and battery-powered devices is an inseparable and invincible feature of our modern life. Meanwhile, the spectrum aggregation, and limited battery capacity of handheld devices challenge the exploding demand and growth of such radio systems. In this work, we try to present two separate solutions for each case; an ultra-wideband (UWB) receiver for Cognitive Radio (CR) applications to deal with spectrum aggregation, and an ultra-low power (ULP) receiver to enhance battery life of handheld wireless devices. Limited linearity and LO harmonics mixing are two major issues that ultra-wideband receivers, and CR in particular, are dealing with. Direct conversion schemes, based on current-driven passive mixers, have shown to improve the linearity, but unable to resolve LO harmonic mixing problem. They are usually limited to 3rd, and 5th harmonics rejection or require very complex and power hungry circuitry for higher number of harmonics. This work presents a heterodyne up-down conversion scheme in 180 nm CMOS technology for CR applications (54-862 MHz band) that mitigates the harmonic mixing issue for all the harmonics, while by employing an active feedback loop, a comparable to the state-of-the art IIP3 of better than +10 dBm is achieved. Measurements show an average NF of 7.5 dB when the active feedback loop is off (i.e. in the absence of destructive interference), and 15.5 dB when the feedback loop is active and a 0 dBm interferer is applied, respectively. Also, the second part of this work presents an ultra-low power super-regenerative receiver (SRR) suitable for OOK modulation and provides analytical insight into its design procedure. The receiver is fabricated in 40 nm CMOS technology and operates in the ISM band of 902-928 MHz. Binary search algorithm through Successive Approximation Register (SAR) architecture is being exploited to calibrate the internally generated quench signal and the working frequency of the receiver. Employing an on-chip inductor and a single-ended to differential architecture for the input amplifier has made the receiver fully integrable, eliminating the need for external components. A power consumption of 320 µW from a 0.65 V supply results in an excellent energy efficiency of 80 pJ/b at 4 Mb/s data rate. The receiver also employs an ADC that enables soft-decisioning and a convenient sensitivity-data rate trade-off, achieving sensitivity of -86.5, and -101.5 dBm at 1000 and 31.25 kbps data rate, respectivel

Integrated Circuit and System Design for Cognitive Radio and Ultra-Low Power Applications

The ubiquitous presence of wireless and battery-powered devices is an inseparable and invincible feature of our modern life. Meanwhile, the spectrum aggregation, and limited battery capacity of handheld devices challenge the exploding demand and growth of such radio systems. In this work, we try to present two separate solutions for each case; an ultra-wideband (UWB) receiver for Cognitive Radio (CR) applications to deal with spectrum aggregation, and an ultra-low power (ULP) receiver to enhance battery life of handheld wireless devices. Limited linearity and LO harmonics mixing are two major issues that ultra-wideband receivers, and CR in particular, are dealing with. Direct conversion schemes, based on current-driven passive mixers, have shown to improve the linearity, but unable to resolve LO harmonic mixing problem. They are usually limited to 3rd, and 5th harmonics rejection or require very complex and power hungry circuitry for higher number of harmonics. This work presents a heterodyne up-down conversion scheme in 180 nm CMOS technology for CR applications (54-862 MHz band) that mitigates the harmonic mixing issue for all the harmonics, while by employing an active feedback loop, a comparable to the state-of-the art IIP3 of better than +10 dBm is achieved. Measurements show an average NF of 7.5 dB when the active feedback loop is off (i.e. in the absence of destructive interference), and 15.5 dB when the feedback loop is active and a 0 dBm interferer is applied, respectively. Also, the second part of this work presents an ultra-low power super-regenerative receiver (SRR) suitable for OOK modulation and provides analytical insight into its design procedure. The receiver is fabricated in 40 nm CMOS technology and operates in the ISM band of 902-928 MHz. Binary search algorithm through Successive Approximation Register (SAR) architecture is being exploited to calibrate the internally generated quench signal and the working frequency of the receiver. Employing an on-chip inductor and a single-ended to differential architecture for the input amplifier has made the receiver fully integrable, eliminating the need for external components. A power consumption of 320 µW from a 0.65 V supply results in an excellent energy efficiency of 80 pJ/b at 4 Mb/s data rate. The receiver also employs an ADC that enables soft-decisioning and a convenient sensitivity-data rate trade-off, achieving sensitivity of -86.5, and -101.5 dBm at 1000 and 31.25 kbps data rate, respectivel

Millimeter-Wave Super-Regenerative Receivers for Wireless Communication and Radar

Today’s world is becoming increasingly automated and interconnected with billions of smart devices coming online, leading to a steep rise in energy consumption from small microelectronics. This coincides with an urgent push to transform global energy production to green energies, causing disruptions and energy shortages, and making the case for efficient energy use ever more pressing. Two major areas where high growth is expected are the fields of wireless communication and radar sensors. Millimeter-wave frequency bands are planned for fifth-generation (5G) and sixth-generation (6G) cellular communication standards, as well as automotive frequency-modulated continuous wave (FMCW) radar systems for driving assistance and automation. Fast silicon-based technologies enable these advances by operating at high maximum frequencies, such as the silicon-germanium (SiGe) heterojunction bipolar transistor (HBT) technologies. However, even the fastest transistors suffer from low and energy expensive gains at millimeter-wave frequencies. Rather than incremental improvements in circuit efficiency using conventional approaches, a disruptive revolution for green microelectronics could be enabled by exploring the low-power benefits of the super-regenerative receiver for some applications. The super-regenerative receiver uses a regenerative oscillator circuit to increase the gain by positive feedback, through coupling energy from the output back into the input. Careful bias and control of the circuit enables a very large gain from a small number of transistors and a very low energy dissipation. Thus, the super-regenerative oscillator could be used to replace amplifier circuits in high data rate wireless communication systems, or as active reflectors to increase the range of FMCW radar systems, greatly reducing the power consumption. The work in this thesis presents fundamental scientific research into the topic of energy-efficient millimeter-wave super-regenerative receivers for use in civilian wireless communication and radar applications. This research work covers the theory, analysis, and simulations, all the way up to the proof of concept, hardware realization, and experimental characterization. Analysis and modeling of regenerative oscillator circuits is presented and used to improve the understanding of the circuit operation, as well as design goals according to the specific application needs. Integrated circuits are investigated and characterized as a proof of concept for a high data rate wireless communication system operating between 140–220 GHz, and an automotive radar system operating at 60 GHz. Amplitude and phase regeneration capabilities for complex modulation are investigated, and principles for spectrum characterization are derived. The circuits are designed and fabricated in a 130 nm SiGe HBT technology, combining bipolar and complementary metal-oxide semiconductor (BiCMOS) transistors. To prove the feasibility of the research concepts, the work achieves a wireless communication link at 16 Gbit/s over 20 cm distance with quadrature amplitude modulation (QAM), which is a world record for the highest data rate ever reported in super-regenerative circuits. This was powered by a super-regenerative oscillator circuit operating at 180 GHz and providing 58 dB of gain. Energy efficiency is also considerably high, drawing 8.8 mW of dc power consumption, which corresponds to a highly efficient 0.6 pJ/bit. Packaging and module integration innovations were implemented for the system experiments, and additional broadband circuits were investigated to generate custom quench waveforms to further enhance the data rate. For radar active reflectors, a regenerative gain of 80 dB is achieved at 60 GHz from a single circuit, which is the best in its frequency range, despite a low dc power consumption of 25 mW

350 mV, 5 GHz Class-D Enhanced Swing Differential and Quadrature VCOs in 65 nm CMOS

A new enhanced swing class-D VCO which operates from a supply voltage as low as 300 mV is presented. The architectural advantages are described along with an analysis for the oscillation frequency. Prototype differential and quadrature variants of the proposed VCO have been implemented in a 65 nm RF CMOS process with a 5 GHz VCO oscillation frequency. At a 350 mV supply, the measured phase noise performance for the quadrature VCO with a 5% tuning range is -137.1 dBc/Hz at 3 MHz offset with a power dissipation of 2.1 mW from a 0.35 V supply. The highest resulting figure-of-merit (FoM) is 198.3 dBc/Hz.©2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works

ARTIFICIAL INTELLIGENT REMOTE CONTROL CAR (AI MOBILE) (A.K.A. REMOTE CONTROL CAR USING MATLAB)

The primary objective of this project is to construct a working prototype of a remote controlled car (a.k.a. AI Mobile) and its ability to control from MATLAB Graphical User Interface (GUI). It involves several EE areas in microcontroller, wireless communication and MATLAB. Secondary objective will be implementing artificial intelligence (AI) in a robot to perform tasks intelligently and autonomously. The car will be enhanced with systems like obstacles detection sensors, wireless camera, wireless microphone, and speed alteration. These systems will be combined by the PIC microcontroller and controlled from the remote computer with the aid of the MS Visual Basic GUI. With these artificial intelligent systems, successful execution of manyhuman-in-loop manipulation tasks which directlydepend on the operator's skill previously can be improved to: (i) permit easy and rapid incorporation of local sensory information to augment performance, and (ii) provide variable performance (precision- and power-) assist for output motions and forces. Such AI systems have enormous potential both reduce operator error and permit integration of greater autonomy into human and robot interactions which will eventually enhance security, safety, and performance. The AI systems are built on an existing platform modified from a remote controlled car. The processor used to coordinate the AI Mobile is the microcontroller PIC16F84A. The independent subsystems for controlling the AI Mobile via Microsoft Visual Basic include the serial communication interface, switching circuit, microcontroller, RF Transmitter & Receiver and Visual Basic programming

Ultra Low Power FM-UWB Transceiver for High-Density Wireless Sensor Networks

The WiseSkin project aims to provide a non-invasive solution for restoration of a natural sense of touch to persons using prosthetic limbs. By embedding sensor nodes into the silicone coating of the prosthesis, which acts as a sensory skin, WiseSkin targets to provide improved gripping, manipulation and mobility for amputees. Flexibility, freedom of movement and comfort demand unobtrusive, highly miniaturized, low-power sensing capabilities built into the artificial skin, which is then integrated with a sensory feedback system. Wireless communication between the sensor nodes provides more flexibility, better scalability and robustness compared to wired solution, and is therefore a preferred approach for WiseSkin. Design of an RF transceiver tailored for the specific needs of WiseSkin is the topic of this work. The properties of FM ultra-wide band (FM-UWB) modulation make it a good candidate for High-Density Wireless Sensor Networks (HD-WSN). The proposed FM-UWB receivers take advantage of short range to reduce power consumption, and exploit robustness of this wideband modulation scheme. The LNA, identified as the biggest consumer, is removed and signal is directly converted to dc, where amplification and demodulation are performed. Owing to 500 MHz bandwidth, frequency offset and phase noise can be tolerated, and a low-power, free-running ring oscillator can be used to generate the LO signal. The receiver is referred to as an approximate zero-IF receiver. Two receiver architectures are studied. The first one performs quadrature downconversion, and owing to the demodulator linearity, provides the multi-user capability. In the second receiver, quadrature demodulation is replaced by the single-ended one. Due to the nature of the demodulator, sensitivity degrades, and multiple FM-UWB signals cannot be resolved, but the consumption is almost halved compared to the first receiver. The proposed approach is verified through two integrations, both in a standard 65 nm bulk CMOS process. In the first run, a standalone quadrature receiver was integrated. Power consumption of 423 uW was measured, while achieving -70 dBm sensitivity. Good narrow-band interference rejection and multiuser capability with up to 4 FM-UWB channels could be achieved. In the second run, a full transceiver is integrated, with both quadrature and single-ended receivers and a transmitter, all sharing a single IO pad, without the need for any external passive components or switches. The quadrature receiver, with on-chip baseband processing and multi-user support, in this case consumes 550 uW, with a sesensitivity of -68 dBm. The low power receiver consumes 267 uW, and provides -57 dBm sensitivity, at a single FM-UWB channel. The implemented trantransmitter transmits a 100 kb/s FM-UWB signal at -11.4 dBm, while drawing 583 uW from the 1 V supply. The on-chip clock recovery allows reference frequency offset up to 8000 ppm. Since state of the art on-chip RC oscillators can provide below 2100 ppm across the temperature range of interest, the implemented transceiver demonstrates the feasibility of a fully integrated FM-UWB radio with no need for a quartz reference or any external components. In addition, the transceiver can tolerate up to 3 dBm narrow-band interferer at 2.4 GHz. Such a strong signal can be used to remotely power the sensor nodes inside the artificial skin and enable a truly wirelessWiseSkin solution