Design of sigma-delta modulators for analog-to-digital conversion intensively using passive circuits

This thesis presents the analysis, design implementation and experimental evaluation of passiveactive discrete-time and continuous-time Sigma-Delta (ΣΔ) modulators (ΣΔMs) analog-todigital converters (ADCs). Two prototype circuits were manufactured. The first one, a discrete-time 2nd-order ΣΔM, was designed in a 130 nm CMOS technology. This prototype confirmed the validity of the ultra incomplete settling (UIS) concept used for implementing the passive integrators. This circuit, clocked at 100 MHz and consuming 298 μW, achieves DR/SNR/SNDR of 78.2/73.9/72.8 dB, respectively, for a signal bandwidth of 300 kHz. This results in a Walden FoMW of 139.3 fJ/conv.-step and Schreier FoMS of 168 dB. The final prototype circuit is a highly area and power efficient ΣΔM using a combination of a cascaded topology, a continuous-time RC loop filter and switched-capacitor feedback paths. The modulator requires only two low gain stages that are based on differential pairs. A systematic design methodology based on genetic algorithm, was used, which allowed decreasing the circuit’s sensitivity to the circuit components’ variations. This continuous-time, 2-1 MASH ΣΔM has been designed in a 65 nm CMOS technology and it occupies an area of just 0.027 mm2. Measurement results show that this modulator achieves a peak SNR/SNDR of 76/72.2 dB and DR of 77dB for an input signal bandwidth of 10 MHz, while dissipating 1.57 mW from a 1 V power supply voltage. The ΣΔM achieves a Walden FoMW of 23.6 fJ/level and a Schreier FoMS of 175 dB. The innovations proposed in this circuit result, both, in the reduction of the power consumption and of the chip size. To the best of the author’s knowledge the circuit achieves the lowest Walden FOMW for ΣΔMs operating at signal bandwidth from 5 MHz to 50 MHz reported to date

Power Efficient Architectures for High Accuracy Analog-to-Digital Converters

Incremental ADCs (IADCs) have found wide applications in sensor interface circuitry since, compared to ∆Σ ADCs, they provide low-latency high-accuracy conversion and easy multiplexing among multiple channels. On the other hand, continuous-time ∆Σ ADCs (CTDSM) have been receiving more and more attention as a power-efficient solution in targeting medium to high accuracy over wider range of signal bandwidth (tens of MHz). In this dissertation, novel configurations have been explored in both architectures for power-efficient and high-accuracy data conversion. First, a multi-step incremental ADC (IADC) using multi-slope extended counting technique is described. Only one active integrator is used in the three-step conversion cycle. The accuracy of the IADC is extended by having it configured as multi-slope ADCs in two additional steps. The proposed IADC uses the same circuitry as a first-order IADC (IADC1), but it exhibits as good efficiency as its second-order ∆Σ ADC counterpart. For the same accuracy, the conversion cycle is shortened by a factor of more than 2⁹ compared to the IADC1. Fabricated in 0.18-μm CMOS process, the prototype ADC occupies 0.5 mm². With a 642 kHz clock, it achieves SNDR of 52.2 dB in the first step. The SNDR is boosted to 79.8 dB in the second step, and to 96.8 dB in the third step, over a 1 kHz signal band. The power consumption is 35 µW from a 1.5 V power supply. This gives an excellent Schreier FoM of 174.6 dB. Secondly, a multi-step incremental ADC with extended binary counting is proposed. It achieves high accuracy by splitting one conversion cycle into two serial steps. During the first step, the ADC works as a first-order incremental ADC (IADC1). The second step reuses the single integrator and extends the accuracy to 16 bits by a two-capacitor SAR-assisted binary counting technique. For the same accuracy, the conversion cycle is shortened by a factor of more than 2⁸ as compared to the single-step IADC. Fabricated in 0.18-μm CMOS process, the SAR-assisted IADC achieves a peak SNR/SNDR/DR of 97.1/96.6/100.2 dB over a 1.2 kHz bandwidth, while dissipating 33.2 μW from a 1.5 V supply. This gives a Schreier FoM of 175.8 dB and Walden FoM of 0.25 pJ/conv.-step. Finally, the design of a continuous-time ∆Σ modulator (CTDSM) to be used in an ultrasound beamformer for biomedical imaging is described. To achieve better resolution, the prototype modulator operates at 1.2 GHz. It incorporates a digital excess loop delay (ELD) compensation to replace the active adder in front of the internal quantizer. A digitally controlled reference-switching matrix, combined with the data-weighted averaging (DWA) technique, results in a delay-free feedback path. A multi-bit FIR feedback DAC, along with its compensation path, is used to achieve lower clock jitter sensitivity and better loop filter linearity. The modulator achieves 79.4 dB dynamic range, 77.3 dB SNR and 74.3 dB SNDR over a 15 MHz signal bandwidth. Fabricated in a 65 nm CMOS process, the core modulator occupies an area of only 0.16 mm² and dissipates 6.96 mW from a 1 V supply. A 58.6 fJ/conversion-step figure of merit was achieved.Keywords: Incremental ADC, multi-step operation, instrumentation and measurement, sensor interface, analog-to-digital converter, extended counting, chopper stabilization, delta-sigma ADC, multi-slope ADCsKeywords: Incremental ADC, multi-step operation, instrumentation and measurement, sensor interface, analog-to-digital converter, extended counting, chopper stabilization, delta-sigma ADC, multi-slope ADC

A Continuous-Time Delta-Sigma Modulator for Biomedical Ultrasound Beamformer Using Digital ELD Compensation and FIR Feedback

This paper presents the design of a continuous-time ΔΣ modulator (CTDSM) to be used in an ultrasound beamformer for biomedical imaging. To achieve better resolution, the prototype modulator operates at 1.2 GHz. It incorporates a digital excess loop delay (ELD) compensation to replace the active adder in front of the internal quantizer. A digitally controlled reference-switching matrix, combined with the data-weighted averaging (DWA) technique, results in a delay-free feedback path. A multi-bit FIR feedback DAC, along with its compensation path, is used to achieve lower clock jitter sensitivity and better loop filter linearity. The modulator achieves 79.4 dB dynamic range, 77.3 dB SNR and 74.3 dB SNDR over a 15 MHz signal bandwidth. Fabricated in a 65 nm CMOS process, the core modulator occupies an area of only 0.16 mm² and dissipates 6.96 mW from a 1 V supply. A 58.6 fJ/conversion-step figure of merit is achieved.This is an author's peer-reviewed final manuscript, as accepted by the publisher. The published article is copyrighted by IEEE-Institute of Electrical and Electronics Engineers and can be found at: http://ieeexplore.ieee.org/xpl/mostRecentIssue.jsp?punumber=8919,©2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.Keywords: Ultrasound beamformer, FIR feedback DAC, Digital excess loop delay compensation, Continuous-time ΔΣ modulato

Wide-bandwidth, high-resolution delta-sigma analog-to-digital converters

There is a significant need in recent mobile communication and wireless broadband systems for high-performance analog-to-digital converters (ADCs) that have wide bandwidth (BW>5-MHz) and high data rate (>100-Mbps). A delta-sigma ADC is recognized as a power-efficient ADC architecture when high resolution (>12-b) is required. This is due to several advantages of the delta-sigma ADC including relaxed anti-aliasing filter requirements, high signal-to-noise and distortion ratio (SNDR) and most importantly, reduced sensitivity to analog imperfections. In this thesis, several structures and design techniques are developed for the implementation of continuoustime (CT) and discrete-time (DT) delta-sigma ADCs. These techniques save the total power consumption, reduce the design complexity, and decrease the chip die area of delta-sigma modulators. First a 4th-order single stage CT delta-sigma ADC with a novel single-amplifier-biquad (SAB) based loop filter is presented. By utilizing the SAB networks in the loop filter of an Nth-order CT delta-sigma modulator, it requires only half the number of active amplifiers and feed-forward branches used in the conventional modulator architecture, thus decreasing the power consumption and area by reducing the number of amplifiers. The proposed scheme also enables the modulator to use a switch-capacitor (SC) adder due to the reduced number of feedforward branches to its summing block. As a sequence, it consumes less power compared to a conventional CT adder. With a 130-nm CMOS technology, the fabricated prototype IC achieves a dynamic range of 80 dB with 10 MHz signal bandwidth and analog power dissipation lower than 12 mW. Presented as the second scheme to save power consumption and chip die area in ΔΣ modulators is a new stage-sharing technique in a discrete-time 2-2 MASH ΔΣ ADC. The proposed technique shares all the active blocks of the modulator second stage with its first stage during the two non-overlapping clock phases. Measurement results show that the modulator designed in a 0.13-um CMOS technology achieves 76 dB SNDR over a 10 MHz conversion bandwidth dissipating less than 9 mW analog power

Design and implementation of a wideband sigma delta ADC

Abstract. High-speed and wideband ADCs have become increasingly important in response to the growing demand for high-speed wireless communication services. Continuous time sigma delta modulators (CTƩ∆M), well-known for their oversampling and noise shaping properties, offer a promising solution for low-power and high-speed design in wireless applications. The objective of this thesis is to design and implement a wideband CTƩ∆M for a global navigation satellite system(GNSS) receiver. The targeted modulator architecture is a 3rdorder single-bit CTƩ∆M, specifically designed to operate within a 15 MHz signal bandwidth. With an oversampling ratio of 25, the ADC’s sampling frequency is set at 768 MHz. The design goal is to achieve a theoretical signal to noise ratio (SNR) of 55 dB. This thesis focuses on the design and implementation of the CTƩ∆M, building upon the principles of a discrete time Ʃ∆ modulator, and leveraging system-level simulation and formulations. A detailed explanation of the coefficient calculation procedure specific to CTƩ∆ modulators is provided, along with a "top-down" design approach that ensures the specified requirements are met. MATLAB scripts for coefficient calculation are also included. To overcome the challenges associated with the implementation of CTƩ∆ modulators, particularly excess loop delay and clock jitter sensitivity, this thesis explores two key strategies: the introduction of a delay compensation path and the utilization of a finite impulse response (FIR) feedback DAC. By incorporating a delay compensation path, the stability of the modulator can be ensured and its noise transfer function (NTF) can be restored. Additionally, the integration of an FIR feedback DAC addresses the issue of clock jitter sensitivity, enhancing the overall performance and robustness of the CTƩ∆M. The CTƩ∆Ms employ the cascade of integrators with feed forward (CIFF) and cascade of integrators with feedforward and feedback (CIFF-B) topologies, with a particular emphasis on the CIFF-B configuration using 22nm CMOS technology node and a supply voltage of 0.8 V. Various simulations are performed to validate the modulator’s performance. The simulation results demonstrate an achievable SNR of 55 dB with a power consumption of 1.36 mW. Furthermore, the adoption of NTF zero optimization techniques enhances the SNR to 62 dB.Laajakaistaisen jatkuva-aikaisen sigma delta-AD-muuntimen suunnittelu ja toteutus. Tiivistelmä. Nopeat ja laajakaistaiset AD-muuntimet ovat tulleet entistä tärkeämmiksi nopeiden langattomien kommunikaatiopalvelujen kysynnän kasvaessa. Jatkuva-aikaiset sigma delta -modulaattorit (CTƩ∆M), joissa käytetään ylinäytteistystä ja kohinanmuokkausta, tarjoavat lupaavan ratkaisun matalan tehonkulutuksen ja nopeiden langattomien sovellusten suunnitteluun. Tämän työn tarkoituksena on suunnitella ja toteuttaa laajakaistainen jatkuva -aikainen sigma delta -modulaattori satelliittipaikannusjärjestelmien (GNSS) vastaanottimeen. Arkkitehtuuriltaan modulaattori on kolmannen asteen 1-bittinen CTƩ∆M, jolla on 15MHz:n signaalikaistanleveys. Ylinäytteistyssuhde on 25 ja AD muuntimen näytteistystaajuus 768 MHz. Tavoitteena on saavuttaa teoreettinen 55 dB signaalikohinasuhde (SNR). Tämä työ keskittyy jatkuva-aikaisen sigma delta -modulaattorin suunnitteluun ja toteutukseen, perustuen diskreettiaikaisen Ʃ∆-modulaattorin periaatteisiin ja systeemitason simulointiin ja mallitukseen. Jatkuva-aikaisen sigma delta -modulaattorin kertoimien laskentamenetelmä esitetään yksityiskohtaisesti, ja vaatimusten täyttyminen varmistetaan “top-down” -suunnitteluperiaatteella. Liitteenä on kertoimien laskemiseen käytetty MATLAB-koodi. Jatkuva-aikaisten sigma delta -modulaattoreiden erityishaasteiden, liian pitkän silmukkaviiveen ja kellojitterin herkkyyden, voittamiseksi tutkitaan kahta strategiaa, viiveen kompensointipolkua ja FIR takaisinkytkentä -DA muunninta. Viivekompensointipolkua käyttämällä modulaattorin stabiilisuus ja kohinansuodatusfunktio saadaan varmistettua ja korjattua. Lisäksi FIR takaisinkytkentä -DA-muuntimen käyttö pienentää kellojitteriherkkyyttä, parantaen jatkuva aikaisen sigma delta -modulaattorin kokonaissuorituskykyä ja luotettavuutta. Toteutetuissa jatkuva-aikaisissa sigma delta -modulaattoreissa on kytketty peräkkäin integraattoreita myötäkytkentärakenteella (CIFF) ja toisessa sekä myötä- että takaisinkytkentärakenteella (CIFF-B). Päähuomio on CIFF-B rakenteessa, joka toteutetaan 22nm CMOS prosessissa käyttäen 0.8 voltin käyttöjännitettä. Suorityskyky varmistetaan erilaisilla simuloinneilla, joiden perusteella 55 dB SNR saavutetaan 1.36 mW tehonkulutuksella. Lisäksi kohinanmuokkausfunktion optimoinnilla SNR saadaan nostettua 62 desibeliin

Design of Highly Efficient Analog-To-Digital Converters

The demand of higher data rates in communication systems is reflected in the constant evolution of communication standards. LTE-A and WiFi 802.11ac promote the use of carrier aggregation to increase the data rate of a wireless receiver. Recent DTV receivers promote the concept of full band capture to avoid the implementation of complex analog operations such as: filtering, equalization, modulation/demodulation, etc. All these operations can be implemented in a robust manner in the digital domain. Analog-to-Digital Converters (ADCs) are located at the heart of such architectures and require to have larger bandwidths and higher dynamic ranges. However, at higher data rates the power efficiency of ADCs tends to degrade. Moreover, while the scale of channel length in CMOS devices directly benefits the power, speed and area of digital circuits, analog circuits suffer from lower intrinsic gain and higher device mismatch. Thus, it has been difficult to design high-speed ADCs with low-power operation using traditional architectures without relying on increasingly complex digital calibration algorithms. This research presents three ADCs that introduce novel architectures to relax the specifications of the analog circuits and reduce the complexity of the digital calibration algorithms. A low-pass sigma delta ADC with 15 MHz of bandwidth is introduced. The system uses a low-power 7-bit quantizer from which the four most significant bits are used for the operation of the sigma delta ADC. The remaining three least significant bits are used for the realization of a frequency domain algorithm for quantization noise improvement. The prototype was implemented in 130 nm CMOS technology. For this prototype, the use of the 7-bit quantizer and algorithm improved the SNDR from 69 dB to 75 dB. The obtained FoM was 145 fJ/conversion-step. In a second project, the problem of high power consumption demanded from closed loop operational amplifiers operating at Giga hertz frequency is addressed. Especially the dependency of the power consumption to the closed loop gain. This project presents a low-pass sigma delta ADC with 75 MHz bandwidth. The traditional summing amplifier used for excess loop compensation delay is substituted by a summing amplifier with current buffer that decouples the power consumption dependency with the closed loop gain. The prototype was designed in 40 nm CMOS technology achieving 64.9 dB peak SNDR. The operating frequency was 3.2 GHz, the total power consumption was 22 mW and FoM of 106 fJ/conversion-step. In a third project, the same approach of decoupling the power consumption requirements from the closed loop gain is applied to a pipelined ADC. The traditional capacitive multiplying DAC used in the residual amplifier is substituted by a current mode DAC and a transimpedance amplifier. The prototype was implemented in 40 nm CMOS technology achieving 58 dB peak SNDR and 76 dB SFDR with 200 MHz sampling frequency. The ADC consumes 8.4 mW with a FoM of 64 fJ/Conversion-step

Micropower incremental analog-to-digital converters

Incremental ADCs (IADCs) have many advantages for low-frequency high-accuracy data conversion—they are easy to multiplex between channels, need simpler digital decimation filter, and allow extended counting with a Nyquist-rate ADC. A single-loop incremental ADC was designed and fabricated in 90 nm for a biosensor interface circuit. It incorporates one integrator, and uses noise-coupling technique to achieve second-order noise-shaping. The use of feed-forward coupling and multi-bit internal quantizer allows low swing at the integrator, and hence low-power operation. The measured SNR is 74 dB within a signal bandwidth 2 kHz, and a 14 μW power consumption. A new two-step IADC was proposed for 250 Hz bandwidth sensor interface circuits. It extends the order of a conventional incremental ADC from N to (2N-1) by way of a two-step operation. However, it only needs the same circuitry as the Nth-order IADC. A second-order loop filter was designed and fabricated by 2.5V I/O devices in 65 nm to demonstrate this concept to achieve third-order noise-shaping performance. Operated at sampling frequency 96 kHz, the measured dynamic range is 99.8 dB relative to a maximum input 2.2 VPP. The measured maximum SNDR was 91 dB with a 2.2 V[subscript PP] input amplitude. The ADC core area is 0.2 mm², and the IADC consumed only 11.7 μW. A new incremental ADC with multi-step extended-counting was proposed for sensor interface conversion. A 1st-order feedforward modulator was used for the coarse conversion, and the residue voltage was quantized by re-using the modulator for the fine conversion. Then, the circuit was re-configured as a counting ADC to quantize the residue voltage. The three steps of the circuits perform 15-bit quantization by 5-bit/step. A first-order IADC could only achieve 6.6-bit performance within the same conversion time of 96 clock periods. Reusing the first-order circuits, extra 8.4-bit is thus achieved

Low Noise, Jitter Tolerant Continuous-Time Sigma-Delta Modulator

The demand for higher data rates in receivers with carrier aggregation (CA) such as LTE, increases the efforts to integrate large number of wireless services into single receiving path, so it needs to digitize the signal in intermediate or high frequencies. It relaxes most of the front-end blocks but makes the design of ADC very challenging. Solving the bottleneck associated with ADC in receiver architecture is a major focus of many ongoing researches. Recently, continuous time Sigma-Delta analog-to-digital converters (ADCs) are getting more attention due to their inherent filtering properties, lower power consumption and wider input bandwidth. But, it suffers from several non-idealities such as clock jitter and ELD which decrease the ADC performance. This dissertation presents two projects that address CT-ΣΔ modulator non-idealities. One of the projects is a CT- ΣΔ modulator with 10.9 Effective Number of Bits (ENOB) with Gradient Descent (GD) based calibration technique. The GD algorithm is used to extract loop gain transfer function coefficients. A quantization noise reduction technique is then employed to improve the Signal to Quantization Noise Ratio (SQNR) of the modulator using a 7-bit embedded quantizer. An analog fast path feedback topology is proposed which uses an analog differentiator in order to compensate excess loop delay. This approach relaxes the requirements of the amplifier placed in front of the quantizer. The modulator is implemented using a third order loop filter with a feed-forward compensation paths and a 3-bit quantizer in the feedback loop. In order to save power and improve loop linearity a two-stage class-AB amplifier is developed. The prototype modulator is implemented in 0.13μm CMOS technology, which achieves peak Signal to Noise and Distortion Ratio (SNDR) of 67.5dB while consuming total power of 8.5-mW under a 1.2V supply with an over sampling ratio of 10 at 300MHz sampling frequency. The prototype achieves Walden's Figure of Merit (FoM) of 146fJ/step. The second project addresses clock jitter non-ideality in Continuous Time Sigma Delta modulators (CT- ΣΔM), the modulator suffer from performance degradation due to uncertainty in timing of clock at digital-to-analog converter (DAC). This thesis proposes to split the loop filter into two parts, analog and digital part to reduce the sensitivity of feedback DAC to clock jitter. By using the digital first-order filter after the quantizer, the effect of clock jitter is reduced without changing signal transfer function (STF). On the other hand, as one pole of the loop filter is implemented digitally, the power and area are reduced by minimizing active analog elements. Moreover, having more digital blocks in the loop of CT- ΣΔM makes it less sensitive to process, voltage, and temperature variations. We also propose the use of a single DAC with a current divider to implement feedback coefficients instead of two DACs to decrease area and clock routing. The prototype is implemented in TSMC 40 nm technology and occupies 0.06 mm^2 area; the proposed solution consumes 6.9 mW, and operates at 500 MS/s. In a 10 MHz bandwidth, the measured dynamic range (DR), peak signal-to-noise-ratio (SNR), and peak signal-to-noise and distortion (SNDR) ratios in presence of 4.5 ps RMS clock jitter (0.22% clock period) are 75 dB, 68 dB, and 67 dB, respectively. The proposed structure is 10 dB more tolerant to clock jitter when compared to the conventional ΣΔM design for similar loop filter

Multi-Stage Noise-Shaping Continuous-Time Sigma-Delta Modulator

The design of a single-loop continuous-time ∑∆ modulator (CT∑∆M) with high resolution, wide bandwidth, and low power consumption is very challenging. The multi-stage noise-shaping (MASH) CT∑∆M architecture is identified as an advancement to the single-loop CT∑∆M architecture in order to satisfy the ever stringent requirements of next generation wireless systems. However, it suffers from the problems of quantization noise leakage and non-ideal interstage interfacing which hinder its widespread adoption. To solve these issues, this dissertation proposes a MASH CT∑∆M with on-chip RC time constant calibration circuits, multiple feedforward interstage paths, and a fully integrated noise cancellation filter (NCF). The prototype core modulator architecture is a cascade of two single-loop second- order CT∑∆M stages, each of which consists of an integrator-based active-RC loop filter, current-steering feedback digital-to-analog converters, and a four-bit flash quantizer. On-chip RC time constant calibration circuits and high gain multi-stage operational amplifiers are realized to mitigate quantization noise leakage due to process variation. Multiple feedforward interstage paths are introduced to (i) synthesize a fourth-order noise transfer function with DC zeros, (ii) simplify the design of NCF, and (iii) reduce signal swings at the second-stage integrator outputs. Fully integrated in 40 nm CMOS, the prototype chip achieves 74.4 dB of signal-to-noise and distortion ratio (SNDR), 75.8 dB of signal-to-noise ratio, and 76.8 dB of dynamic range in 50.3 MHz of bandwidth (BW) at 1 GHz of sampling frequency with 43.0 mW of power consumption (P). It does not require external software calibration and possesses minimal out-of-band signal transfer function peaking. The figure-of-merit (FOM), defined as FOM = SNDR + 10 log10(BW/P), is 165.1 dB