Wavelength tunable transmitters for future reconfigurable agile optical networks

Wavelength tuneable transmission is a requirement for future reconfigurable agile optical networks as it enables cost efficient bandwidth distribution and a greater degree of transparency. This thesis focuses on the development and characterisation of wavelength tuneable transmitters for the core, metro and access based WDM networks. The wavelength tuneable RZ transmitter is a fundamental component for the core network as the RZ coding scheme is favoured over the conventional NRZ format as the line rate increases. The combination of a widely tuneable SG DBR laser and an EAM is a propitious technique employed to generate wavelength tuneable pulses at high repetition rates (40 GHz). As the EAM is inherently wavelength dependant an accurate characterisation of the generated pulses is carried out using the linear spectrogram measurement technique. Performance issues associated with the transmitter are investigated by employing the generated pulses in a 1500 km 42.7 Gb/s circulating loop system. It is demonstrated that non-optimisation of the EAM drive conditions at each operating wavelength can lead to a 33 % degradation in system performance. To achieve consistent operation over a wide waveband the drive conditions of the EAM must be altered at each operating wavelength. The metro network spans relatively small distances in comparison to the core and therefore must utilise more cost efficient solutions to transmit data, while also maintaining high reconfigurable functionality. Due to the shorter transmission distances, directly modulated sources can be utilised, as less precise wavelength and chirp control can be tolerated. Therefore a gain-switched FP laser provides an ideal source for wavelength tuneable pulse generation at high data rates (10 Gb/s). A self-seeding scheme that generates single mode pulses with high SMSR (> 30 dB) and small pulse duration is demonstrated. A FBG with a very large group delay disperses the generated pulses and subsequently uses this CW like signal to re-inject the laser diode negating the need to tune the repetition rate for optimum gain-switching operation. The access network provides the last communication link between the customer’s premises and the first switching node in the network. FTTH systems should take advantage of directly modulated sources; therefore the direct modulation of a SG DBR tuneable laser is investigated. Although a directly modulated TL is ideal for reconfigurable access based networks, the modulation itself leads to a drift in operating frequency which may result in cross channel interference in a WDM network. This effect is investigated and also a possible solution to compensate the frequency drift through simultaneous modulation of the lasers phase section is examined

High-speed optical fibre transmission using advanced modulation formats

The rapid growth in interactive bandwidth-hungry services demands ever higher capacity at various stages of the optical network, leading to a potential capacity exhaust, termed the capacity crunch. The main aim of the research work described in this thesis was to help solve the potential capacity crunch by exploring techniques to increase the data rate, spectral efficiency and reach of optical fibre systems. The focus was on the use of advanced signal modulation formats, including optical time-division multiplexing (OTDM), quadrature phase shift keying (QPSK), and 16-state quadrature amplitude modulation (QAM16). QPSK and QAM16 modulations formats were studied in combination with coherent detection and digital signal processing (DSP) for the compensation of transmission impairments. In addition, return-to-zero (RZ) pulses were explored to increase the tolerance towards nonlinearity for coherently detected signals, and nonlinearity compensation (NLC) through the DSP. Initially, to maximise the bit-rate, research was focused on the study of OTDM transmission at 80Gbit/s with the aim to optimise the phase difference between the adjacent OTDM channels. A new technique to achieve bit-wise phase control using a phase-stabilised fibre interferometer was proposed. Faced with a limited fibre capacity, the need to maximise the spectral efficiency became paramount, and thus the need to use phase, amplitude and polarisation domains for signal transmission. In combination with coherent detection the research focused on the performance of optical fibre systems using QPSK and QAM16 modulation formats, including their generation, transmission and detection in single-channel and WDM regimes. This included the study of the impact of pulse shapes, and the mitigation of linear and nonlinear transmission impairments with receiver-based DSP at bit-rates ranging from 42.7 to 224Gbit/s. The technique demonstrated for bit-wise phase control for OTDM was successfully used to demonstrate a new method for QAM16 signal generation. Longest transmission distances (up to 10160km in 112Gbit/s QPSK, 4240km in 112Gbit/s QAM16, and 2000km in 224Gbit/s QAM16) have been achieved with the use of NLC and RZ pulses. The efficiency of these two techniques is explored through a comprehensive set of experiments in both single-channel and WDM transmission experiments. The results can be used in the design of future optical transmission systems

High capacity photonic integrated switching circuits

As the demand for high-capacity data transfer keeps increasing in high performance computing and in a broader range of system area networking environments; reconfiguring the strained networks at ever faster speeds with larger volumes of traffic has become a huge challenge. Formidable bottlenecks appear at the physical layer of these switched interconnects due to its energy consumption and footprint. The energy consumption of the highly sophisticated but increasingly unwieldy electronic switching systems is growing rapidly with line rate, and their designs are already being constrained by heat and power management issues. The routing of multi-Terabit/second data using optical techniques has been targeted by leading international industrial and academic research labs. So far the work has relied largely on discrete components which are bulky and incurconsiderable networking complexity. The integration of the most promising architectures is required in a way which fully leverages the advantages of photonic technologies. Photonic integration technologies offer the promise of low power consumption and reduced footprint. In particular, photonic integrated semiconductor optical amplifier (SOA) gate-based circuits have received much attention as a potential solution. SOA gates exhibit multi-terahertz bandwidths and can be switched from a high-gain state to a high-loss state within a nanosecond using low-voltage electronics. In addition, in contrast to the electronic switching systems, their energy consumption does not rise with line rate. This dissertation will discuss, through the use of different kind of materials and integration technologies, that photonic integrated SOA-based optoelectronic switches can be scalable in either connectivity or data capacity and are poised to become a key technology for very high-speed applications. In Chapter 2, the optical switching background with the drawbacks of optical switches using electronic cores is discussed. The current optical technologies for switching are reviewed with special attention given to the SOA-based switches. Chapter 3 discusses the first demonstrations using quantum dot (QD) material to develop scalable and compact switching matrices operating in the 1.55µm telecommunication window. In Chapter 4, the capacity limitations of scalable quantum well (QW) SOA-based multistage switches is assessed through experimental studies for the first time. In Chapter 5 theoretical analysis on the dependence of data integrity as ultrahigh line-rate and number of monolithically integrated SOA-stages increases is discussed. Chapter 6 presents some designs for the next generation of large scale photonic integrated interconnects. A 16x16 switch architecture is described from its blocking properties to the new miniaturized elements proposed. Finally, Chapter 7 presents several recommendations for future work, along with some concluding remark

Investigation of the impact of fibre impairments and SOA-based devices on 2D-WH/TS OCDMA codes

In seeking efficient last-mile solutions for high-capacity, optical code division multiple access (OCDMA) emerges as a promising alternative high-speed optical network that can securely support a multitude of simultaneous users without requiring extensive equipment. This multiplexing technique has recently been the subject of comprehensive research, highlighting its potential for facilitating high-bandwidth multi-access networking. When contrasted with techniques such as wavelength division multiplexing (WDM) and optical time division multiplexing (OTDM), OCDMA offers a more effective and equitable split of available fibre bandwidth among the users. This thesis presents my research focused on the incoherent OCDMA under the influence of optical fibre impairments that uses picosecond multiwavelength pulses to form two-dimensional wavelength hopping time-spreading (2D-WH/TS) incoherent OCDMA codes. In particular, self-phase modulation, temperature induced fibre dispersion, chromatic dispersion, as well as the impact of semiconductor optical amplifier SOA devices deployment on 2D-WH/TS OCDMA code integrity were investigated. These aspects were investigated using a 17-km long bidirectional fibre link between Strathclyde and Glasgow University. In particular, I investigated the impact of temporal skewing among OCDMA code carriers and the importance of selecting small range of wavelengths as code carriers where wide range manifest high dependency on wavelength. This wavelength dependency is exploited furthermore to measure the induced temperature dispersion coefficient accurately and economically. I have conducted experiments to characterise the impact of SOA-device on 2D OCDMA code carries which is evaluated under different bias conditions. This evaluation addressed the potential challenges and ramifications of the gain recovery time of SOA and its wavelength dependency with respect to gain ratio and self-phase modulation (SPM). The OCDMA code was built using multiplexers and delay lines to create a 2D OCDMA code to allow studying the impact of deploying a SOA under different conditions on each wavelength. The concept described above is then extended to the investigation of the SOA’s impact on a 2D-WH/TS OCDMA prime code under high bias current/gain conditions. The overall performance of two different 2D-WH/TS OCDMA systems deploying the SOA was also calculated. I have also investigated the possibility of manipulating chirp in 2D-WH/TS incoherent OCDMA to counteract the self-phase modulation-induced red shift by using single mode fibre and lithium crystals. I have investigated the performance of the picosecond code based optical signal when subjected to temperature variations similar to that experience by most buried fibre systems. I have proposed and demonstrated a novel technique, which I examined analytically and experimentally, that utilises a SOA at the transmitter to create a new code with a new wavelength hopping and spreading time sequences to achieve a unique physical improved secure incoherent OCDMA communication method. A novel fully automated tuneable compensation testbed is also proposed of an autonomous dispersion management in a WH/TS incoherent OCDMA system. The system proposed manipulates the chirp of OCDMA code carriers to limit chromatic dispersion detrimental effect on transmission systems.In seeking efficient last-mile solutions for high-capacity, optical code division multiple access (OCDMA) emerges as a promising alternative high-speed optical network that can securely support a multitude of simultaneous users without requiring extensive equipment. This multiplexing technique has recently been the subject of comprehensive research, highlighting its potential for facilitating high-bandwidth multi-access networking. When contrasted with techniques such as wavelength division multiplexing (WDM) and optical time division multiplexing (OTDM), OCDMA offers a more effective and equitable split of available fibre bandwidth among the users. This thesis presents my research focused on the incoherent OCDMA under the influence of optical fibre impairments that uses picosecond multiwavelength pulses to form two-dimensional wavelength hopping time-spreading (2D-WH/TS) incoherent OCDMA codes. In particular, self-phase modulation, temperature induced fibre dispersion, chromatic dispersion, as well as the impact of semiconductor optical amplifier SOA devices deployment on 2D-WH/TS OCDMA code integrity were investigated. These aspects were investigated using a 17-km long bidirectional fibre link between Strathclyde and Glasgow University. In particular, I investigated the impact of temporal skewing among OCDMA code carriers and the importance of selecting small range of wavelengths as code carriers where wide range manifest high dependency on wavelength. This wavelength dependency is exploited furthermore to measure the induced temperature dispersion coefficient accurately and economically. I have conducted experiments to characterise the impact of SOA-device on 2D OCDMA code carries which is evaluated under different bias conditions. This evaluation addressed the potential challenges and ramifications of the gain recovery time of SOA and its wavelength dependency with respect to gain ratio and self-phase modulation (SPM). The OCDMA code was built using multiplexers and delay lines to create a 2D OCDMA code to allow studying the impact of deploying a SOA under different conditions on each wavelength. The concept described above is then extended to the investigation of the SOA’s impact on a 2D-WH/TS OCDMA prime code under high bias current/gain conditions. The overall performance of two different 2D-WH/TS OCDMA systems deploying the SOA was also calculated. I have also investigated the possibility of manipulating chirp in 2D-WH/TS incoherent OCDMA to counteract the self-phase modulation-induced red shift by using single mode fibre and lithium crystals. I have investigated the performance of the picosecond code based optical signal when subjected to temperature variations similar to that experience by most buried fibre systems. I have proposed and demonstrated a novel technique, which I examined analytically and experimentally, that utilises a SOA at the transmitter to create a new code with a new wavelength hopping and spreading time sequences to achieve a unique physical improved secure incoherent OCDMA communication method. A novel fully automated tuneable compensation testbed is also proposed of an autonomous dispersion management in a WH/TS incoherent OCDMA system. The system proposed manipulates the chirp of OCDMA code carriers to limit chromatic dispersion detrimental effect on transmission systems

Single-Laser Multi-Terabit/s Systems

Optical communication systems carry the bulk of all data traffic worldwide. This book introduces multi-Terabit/s transmission systems and three key technologies for next generation networks. A software-defined multi-format transmitter, an optical comb source and an optical processing scheme for the fast Fourier transform for Tbit/s signals. Three world records demonstrate the potential: The first single laser 10 Tbit/s and 26 Tbit/s OFDM and the first 32.5 Tbit/s Nyquist WDM experiments

Single-Laser Multi-Terabit/s Systems

Optical communication systems carry the bulk of all data traffic worldwide. This book introduces multi-Terabit/s transmission systems and three key technologies for next generation networks. A software-defined multi-format transmitter, an optical comb source and an optical processing scheme for the fast Fourier transform for Tbit/s signals. Three world records demonstrate the potential: The first single laser 10 Tbit/s and 26 Tbit/s OFDM and the first 32.5 Tbit/s Nyquist WDM experiments

High speed nonlinear optical components for next-generation optical communications

Electronic signal processing systems currently employed at core internet routers require huge amounts of power to operate and they may be unable to continue to satisfy consumer demand for more bandwidth without an inordinate increase in cost, size and/or energy consumption. Optical signal processing techniques may be deployed in next-generation optical networks for simple tasks such as wavelength conversion, demultiplexing and format conversion at high speed (≥100Gb.s-1) to alleviate the pressure on existing core router infrastructure. To implement optical signal processing functionalities, it is necessary to exploit the nonlinear optical properties of suitable materials such as III-V semiconductor compounds, silicon, periodically-poled lithium niobate (PPLN), highly nonlinear fibre (HNLF) or chalcogenide glasses. However, nonlinear optical (NLO) components such as semiconductor optical amplifiers (SOAs), electroabsorption modulators (EAMs) and silicon nanowires are the most promising candidates as all-optical switching elements vis-à-vis ease of integration, device footprint and energy consumption. This PhD thesis presents the amplitude and phase dynamics in a range of device configurations containing SOAs, EAMs and/or silicon nanowires to support the design of all optical switching elements for deployment in next-generation optical networks. Time-resolved pump-probe spectroscopy using pulses with a pulse width of 3ps from mode-locked laser sources was utilized to accurately measure the carrier dynamics in the device(s) under test. The research work into four main topics: (a) a long SOA, (b) the concatenated SOA-EAMSOA (CSES) configuration, (c) silicon nanowires embedded in SU8 polymer and (d) a custom epitaxy design EAM with fast carrier sweepout dynamics. The principal aim was to identify the optimum operation conditions for each of these NLO device configurations to enhance their switching capability and to assess their potential for various optical signal processing functionalities. All of the NLO device configurations investigated in this thesis are compact and suitable for monolithic and/or hybrid integration

Dispositivos fotónicos para processamento de sinais ópticos e de RF

Doutoramento em Engenharia ElectrotécnicaO presente trabalho tem por objectivo o estudo de novos dispositivos fotónicos aplicados a sistemas de comunicações por fibra óptica e a sistemas de processamento de sinais RF. Os dispositivos apresentados baseiam-se em processamento de sinal linear e não linear. Dispositivos lineares ópticos tais como o interferómetro de Mach-Zehnder permitem adicionar sinais ópticos com pesos fixos ou sintonizáveis. Desta forma, este dispositivo pode ser usado respectivamente como um filtro óptico em amplitude com duas saídas complementares, ou, como um filtro óptico de resposta de fase sintonizável. O primeiro princípio de operação serve como base para um novo sistema fotónico de medição em tempo real da frequência de um sinal RF. O segundo princípio de operação é explorado num novo sistema fotónico de direccionamento do campo eléctrico radiado por um agregado de antenas, e também num novo compensador sintonizável de dispersão cromática. O processamento de sinal é não linear quando sinais ópticos são atrasados e posteriormente misturados entre si, em vez de serem linearmente adicionados. Este princípio de operação está por detrás da mistura de um sinal eléctrico com um sinal óptico, que por sua vez é a base de um novo sistema fotónico de medição em tempo real da frequência de um sinal RF. A mistura de sinais ópticos em meios não lineares permite uma operação eficiente numa grande largura espectral. Tal operação é usada para realizar conversão de comprimento de onda sintonizável. Um sinal óptico com multiplexagem no domínio temporal de elevada largura de banda é misturado com duas bombas ópticas não moduladas com base em processos não lineares paramétricos num guia de ondas de niobato de lítio com inversão periódica da polarização dos domínios ferroeléctricos. Noutro trabalho, uma bomba pulsada em que cada pulso tem um comprimento de onda sintonizável serve como base a um novo conversor de sinal óptico com multiplexagem no domínio temporal para um sinal óptico com multiplexagem no comprimento de onda. A bomba é misturada com o sinal óptico de entrada através de um processo não linear paramétrico numa fibra óptica com parâmetro não linear elevado. Todos os dispositivos fotónicos de processamento de sinal linear ou não linear propostos são experimentalmente validados. São também modelados teoricamente ou através de simulação, com a excepção dos que envolvem mistura de sinais ópticos. Uma análise qualitativa é suficiente nestes últimos dispositivos.This work investigates novel photonic devices for optical fiber communication systems and microwave photonics. Such devices rely on linear and nonlinear optical signal processing. Basic linear optical devices such as the Mach-Zehnder delay interferometer enable delaying and adding optical signals with fixed or variable weights. Therefore, such device can be respectively used as an optical amplitude filter with two complementary optical outputs, or, as an optical phase filter with tunable group delay response. The first operation principle is explored in a novel instantaneous RF frequency measurement system, whereas the latter serves as basis to a novel photonic beamforming system for a phase array antenna, and also to a novel tunable optical dispersion compensator. Nonlinear optical signal processing is obtained when optical signals are delayed and mixed, instead of being linearly added. Such operation principle is behind electro-optical mixing, which is explored in a novel instantaneous RF frequency measurement system. All-optical mixing enables ultra-fast and thereby broad bandwidth operation. This operation principle is explored to obtain tunable wavelength conversion. An optical time division multiplexed signal with a large spectral width is parametrically mixed with two continuous wave pumps in a periodically-poled lithium niobate waveguide. Instead of continuous wave pumps, a pulsed pump in which each pulse has a tunable wavelength enables a novel routable optical time-to-wavelength division converter. The pump signal is parametrically mixed with the input optical signal in a highly nonlinear optical fiber. All the proposed linear and nonlinear optical signal processing devices are experimentally validated. In addition, theoretical modeling and simulations are presented in all concepts, with the exception of the ones which employ alloptical mixing. A qualitative analysis is sufficient for the latter devices