425 research outputs found
Design of a Cost-Efficient Reconfigurable Pipeline ADC
Power budget is very critical in the design of battery-powered implantable biomedical instruments. High speed, high resolution and low power usually cannot be achieved at the same time. Therefore, a tradeoff must be made to compromise every aspect of those features. As the main component of the bioinstrument, high conversion rate, high resolution ADC consumes most of the power. Fortunately, based on the operation modes of the bioinstrument, a reconfigurable ADC can be used to solve this problem. The reconfigurable ADC will operate at 10-bit 40 MSPS for the diagnosis mode and at 8-bit 2.5 MSPS for the monitor mode. The ADC will be completely turned off if no active signal comes from sensors or if an off command is received from the antenna.
By turning off the sample hold stage and the first two stages of the pipeline ADC, a significant power saving is achieved. However, the reconfigurable ADC suffers from two drawbacks. First, the leakage signals through the extra off-state switches in the third stage degrade the performance of the data converter. This situation tends to be even worse for high speed and high-resolution applications. An interference elimination technique has been proposed in this work to solve this problem. Simulation results show a significant attenuation of the spurious tones. Moreover, the transistors in the OTA tend to operate in weak inversion region due to the scaling of the bias current. The transistor in subthreshold is very slow due to the small transit frequency. In order to get a better tradeoff between the transconductance efficiency and the transit frequency, reconfigurable OTAs and scalable bias technique are devised to adjust the operating point from weak inversion to moderate inversion.
The figure of merit of the reconfigurable ADC is comparable to the previously published conventional pipeline ADCs. For the 10-bit, 40 MSPS mode, the ADC attains a 56.9 dB SNDR for 35.4 mW power consumption. For the 8-bit 2.5 MSPS mode, the ADC attains a 49.2 dB SNDR for 7.9 mW power consumption. The area for the core layout is 1.9 mm2 for a 0.35 micrometer process
Design and Implementation of an RF Front-End for Software Defined Radios
Software Defined Radios have brought a major reformation in the design standards for radios, in which a large portion of the functionality is implemented through pro grammable signal processing devices, giving the radio the ability to change its op erating parameters to accommodate new features and capabilities. A software radio approach reduces the content of radio frequency and other analog components of the traditional radios and emphasizes digital signal processing to enhance overall receiver flexibility. Field Programmable Gate Arrays (FPGA) are a suitable technology for the hardware platform as they offer the potential of hardware-like performance coupled with software-like programmability.
Software defined radio is a very broad field, encompassing the design of various technologies all the way from the antenna to RF, IF, and baseband digital design. The RF section primarily consists of analog hardware modules. The IF and baseband sections are primarily digital. It is the general process of the radio to convert the incoming signal from RF to IF and then IF to baseband for better signal processing system.
In this thesis, some of major building blocks of a Software defined radio are de signed and implemented using FPGAs. The design of a Digital front end, which provides the bridge between the baseband and analog RF portions of a wireless receiver, is synthesized. The Digital front end receiver consists of a digital down converter(DDC) which in turn comprises of a direct digital frequency synthesizer (DDFS), a phase accumulator and a low pass filter. The signal processing block
of the DDFS is executed using Co-ordinate Rotation Digital Computer (CORDIC) iii
Abstract
algorithm. Cascaded-Integrator-Comb filters (CIC) are implemented for changing the sample rate of the incoming data. Application of a DDC includes software ra dios, multicarrier, multimode digital receivers, micro and pico cell systems,broadband data applications, instrumentation and test equipment and in-building wireless tele phony. Also, in this thesis, interfaces for connecting Texas Instruments high speed and high resolution Analog-to-Digital converters (ADC) and Digital-to-Analog converters (DAC) with Xilinx Virtex-5 FPGAs are also implemented and demonstrated
Design of Analog-to-Digital Converters with Embedded Mixing for Ultra-Low-Power Radio Receivers
In the field of radio receivers, down-conversion methods usually rely on one (or more)
explicit mixing stage(s) before the analog-to-digital converter (ADC). These stages not
only contribute to the overall power consumption but also have an impact on area and can
compromise the receiver’s performance in terms of noise and linearity. On the other hand,
most ADCs require some sort of reference signal in order to properly digitize an analog
input signal. The implementation of this reference signal usually relies on bandgap
circuits and reference buffers to generate a constant, stable, dc signal. Disregarding this
conventional approach, the work developed in this thesis aims to explore the viability
behind the usage of a variable reference signal. Moreover, it demonstrates that not only
can an input signal be properly digitized, but also shifted up and down in frequency,
effectively embedding the mixing operation in an ADC. As a result, ADCs in receiver
chains can perform double-duty as both a quantizer and a mixing stage. The lesser known
charge-sharing (CS) topology, within the successive approximation register (SAR) ADCs,
is used for a practical implementation, due to its feature of “pre-charging” the reference
signal prior to the conversion. Simulation results from an 8-bit CS-SAR ADC designed in
a 0.13 μm CMOS technology validate the proposed technique
Recommended from our members
Efficient, High power Precision RF and mmWave Digital Transmitter Architectures
Digital transmitters offer several advantages over conventional analog transmitters such as reconfigurability, elimination of scaling-unfriendly, power hungry and bulky analog blocks and portability across technology. The rapid advancement of technology in CMOS processes also enables integration of complex digital signal processing circuitry on the same die as the digital transmitter to compensate for their non-idealities. The use of this digital assistance can, for instance, enable the use of highly efficient but nonlinear switching-class power amplifiers by compensating for their severe nonlinearity through digital predistortion. While this shift to digitally intensive transmitter architectures is propelled by the benefits stated above, several pressing challenges arise that vary in their nature depending on the frequency of operation - from RF to mmWave.
Millimeter wave CMOS power amplifiers have traditionally been limited in output power due to the low breakdown voltage of scaled CMOS technologies and poor quality of on-chip passives. Moreover, high data-rates and efficient spectrum utilization demand highly linear power amplifiers with high efficiency under back-off. However, linearity and high efficiency are traditionally at odds with each other in conventional power amplifier design. In this dissertation, digital assistance is used to relax this trade-off and enable the use of state-of-the-art switching class power amplifiers. A novel digital transmitter architecture which simultaneously employs aggressive device-stacking and large-scale power combining for watt-class output power, dynamic load modulation for linearization, and improved efficiency under back-off by supply-switching and load modulation is presented.
At RF frequencies, while the problem of watt-class power amplification has been long solved, more pressing challenges arise from the crowded spectrum in this regime. A major drawback of digital transmitters is the absence of a reconstruction filter after digital-to-analog conversion which causes the baseband quantization noise to get upconverted to RF and amplified at the output of the transmitter. In high power transmitters, this upconverted noise can be so strong as to prevent their use in FDD systems due to receiver desensitization or impose stringent coexistence challenges. In this dissertation, new quantization noise suppression techniques are presented which, for the first time, contribute toward making watt-class fully-integrated digital RF transmitters a viable alternative for FDD and coexistence scenarios. Specifically, the techniques involve embedding a mixed-domain multi-tap FIR filter within highly-efficient watt-class switching power amplifiers to suppress quantization noise, enhancing the bandwidth of noise suppression, enabling tunable location of suppression and overcoming the limitations of purely digital-domain filtering techniques for quantization noise
Voltage-to-Time Converter for High-Speed Time-Based Analog-to-Digital Converters
In modern complementary metal oxide semiconductor (CMOS) technologies, the supply voltage scales faster than the threshold voltage (Vth) of the transistors in successive smaller nodes. Moreover, the intrinsic gain of the transistors diminishes as well. Consequently, these issues increase the difficulty of designing higher speed and larger resolution analog-to-digital converters (ADCs) employing voltage-domain ADC architectures. Nevertheless, smaller transistor dimensions in state-of-the-art CMOS technologies leads to reduced capacitance, resulting in lower gate delays. Therefore, it becomes beneficial to first convert an input voltage to a 'time signal' using a voltage-to-time converter (VTC), instead of directly converting it into a digital output. This 'time-signal' could then be converted to a digital output through a time-to-digital converter (TDC) for complete analog-to-digital conversion. However, the overall performance of such an ADC will still be limited to the performance level of the voltage-to-time conversion process.
Hence, this thesis presents the design of a linear VTC for a high-speed time-based ADC in 28 nm CMOS process. The proposed VTC consists of a sample-and-hold (S/H) circuit, a ramp generator and a comparator to perform the conversion of the input signal from the voltage to the time domain. Larger linearity is attained by integrating a constant current (with high output impedance) over a capacitor, generating a linear ramp. The VTC operates at 256 MSPS consuming 1.3 mW from 1 V supply with a full-scale 1 V pk-pk differential input signal, while achieving a time-domain output signal with a spurious-free-dynamic-range (SFDR) of 77 dB and a signal-to-noise-and-distortion ratio (SNDR) of 56 dB at close to Nyquist frequency (f = 126.5 MHz). The proposed VTC attains an output range of 2.7 ns, which is the highest linear output range for a VTC at this speed, published to date
Millimeter-wave Communication and Radar Sensing — Opportunities, Challenges, and Solutions
With the development of communication and radar sensing technology, people are able to seek for a more convenient life and better experiences. The fifth generation (5G) mobile network provides high speed communication and internet services with a data rate up to several gigabit per second (Gbps). In addition, 5G offers great opportunities of emerging applications, for example, manufacture automation with the help of precise wireless sensing. For future communication and sensing systems, increasing capacity and accuracy is desired, which can be realized at millimeter-wave spectrum from 30 GHz to 300 GHz with several tens of GHz available bandwidth. Wavelength reduces at higher frequency, this implies more compact transceivers and antennas, and high sensing accuracy and imaging resolution. Challenges arise with these application opportunities when it comes to realizing prototype or demonstrators in practice. This thesis proposes some of the solutions addressing such challenges in a laboratory environment.High data rate millimeter-wave transmission experiments have been demonstrated with the help of advanced instrumentations. These demonstrations show the potential of transceiver chipsets. On the other hand, the real-time communication demonstrations are limited to either low modulation order signals or low symbol rate transmissions. The reason for that is the lack of commercially available high-speed analog-to-digital converters (ADCs); therefore, conventional digital synchronization methods are difficult to implement in real-time systems at very high data rates. In this thesis, two synchronous baseband receivers are proposed with carrier recovery subsystems which only require low-speed ADCs [A][B].Besides synchronization, high-frequency signal generation is also a challenge in millimeter-wave communications. The frequency divider is a critical component of a millimeter-wave frequency synthesizer. Having both wide locking range and high working frequencies is a challenge. In this thesis, a tunable delay gated ring oscillator topology is proposed for dual-mode operation and bandwidth extension [C]. Millimeter-wave radar offers advantages for high accuracy sensing. Traditional millimeter-wave radar with frequency-modulated continuous-wave (FMCW), or continuous-wave (CW), all have their disadvantages. Typically, the FMCW radar cannot share the spectrum with other FMCW radars.\ua0 With limited bandwidth, the number of FMCW radars that could coexist in the same area is limited. CW radars have a limited ambiguous distance of a wavelength. In this thesis, a phase-modulated radar with micrometer accuracy is presented [D]. It is applicable in a multi-radar scenario without occupying more bandwidth, and its ambiguous distance is also much larger than the CW radar. Orthogonal frequency-division multiplexing (OFDM) radar has similar properties. However, its traditional fast calculation method, fast Fourier transform (FFT), limits its measurement accuracy. In this thesis, an accuracy enhancement technique is introduced to increase the measurement accuracy up to the micrometer level [E]
A robust 2.4 GHz time-of-arrival based ranging system with sub-meter accuracy: feasibility study and realization of low power CMOS receiver
Draadloze sensornetwerken worden meer en meer aangewend om verschillende soorten informatie te verzamelen. De locatie, waar deze informatie verzameld is, is een belangerijke eigenschap en voor sommige toepassingen, zoals het volgen van personen of goederen, zelfs de meest belangrijke en mogelijkmakende factor. Om de positie van een sensor te bepalen, is een technologie nodig die de afstand tot een gekend referentiepunt schat. Door verschillende afstandsmetingen te combineren, is het mogelijk de absolute locatie van de node te berekenen
- …