Microwave radiometer for subsurface temperature measurement

A UHF radiometer, operating at a frequency of 800 MHz, was modified to provide an integral, three frequency voltage standing wave ratio (VSWR) circuit in the radio frequency (RF) head. The VSWR circuit provides readings of power transmission at the antenna-material interface with an accuracy of plus or minus 5 percent. The power transmission readings are numerically equal to the emissivity of the material under observation. Knowledge of material emissivity is useful in the interpretation of subsurface apparent temperatures obtained on phantom models of biological tissue. The emissivities of phantom models consisting of lean beefsteak were found to lie in the range 0.623 to 0.779, depending on moisture content. Radiometric measurements performed on instrumented phantoms showed that the radiometer was capable of sensing small temperature changes occurring at depths of at least 19 to 30 mm. This is consistent with previously generated data which showed that the radiometer could sense temperatures at a depth of 38 mm

Analog 16-hydrophone vertical line array for the acoustic - oceanographic buoy - AOB

SiPLAB Report 03/06, FCT, University of Algarve,2006.This report contains the user guide and the system reference for the analog 16-hydrophone AOB vertical line array. The array is a 67.5m long cable with 16 4m-spaced hydrophones and 17 digital thermistor sensors, distributed along its length. Each module has a dedicated preamplifier to increase signal strength at the hydrophone output and drive a balanced line to transmit the signal to the surface buoy's electronics. The thermistor sensors are digital devices that transmit the temperatures values through a 1-wire digital serial bus. This report presents the system user guide and the system reference guide. The user guide has instructions for system deployment, everyday usage and maintenance. The system reference guide is intended for specialized technicians for system repairing and/or upgrade.This work was partially supported by projects RADAR (POCTI/CTA/47719/2002) and UAB (POCI/MAR/59008/2004) from FCT, Portugal

Possibility to sound the atmospheric ozone by a radiosonde equipped with two temperature sensors, sensitive and non-sensitive to the long wave radiation

The sensitiveness of white coated thermistor sensors and non-sensitiveness of the gold coated over white thermistor sensors (which have been manufactured by a vacuum evaporation process) to long wave radiation were ascertained by some simple experiments in-room and also by analyses of some results of experimental soundings. From results of analyses on the temperature discrepancies caused by long wave radiation, the possibility to sound the atmospheric ozone partial pressure by a radiosonde equipped with two kinds of sensors, sensitive and non-sensitive to the long wave radiation was suggested, and the test results of the newly developed software for the deduction of ozone partial pressure in upper layers was also shown. However, it was found that the following is the necessary condition to realize the purpose. The sounding should be made by a radiosonde equipped with three sensors, instead of two, one being non-sensitive to the long wave radiation perfectly, and the other two also non-sensitive partially to the downward one, with two different angles of exposure upward. It is essential for the realization of the purpose to get two different values of temperature discrepancies simultaneously observed by the three sensors mentioned above and to avoid the troublesome effects of the upward long wave radiation

Three-Axis’ Heat Loss Anemometer Comprising Thick-Film Segmented Thermistors

NTC thick-film segmented thermistors were used as anemometer sensing devices. They were screen printed of thick-film thermistor paste based on modified NiMn2O4 fine powder, organic vehicle, and glass frit. Their electrical properties, such as resistance vs. temperature R(T) and thermistor exponential factor B were obtained using measurements in the climatic test chamber. A uniaxial anemometer was formed using a thick-film segmented thermistor, which was placed in the hole drilled in rectangular piece of thermally insulating material. The uniaxial anemometer was used for the optimization of operating point of segmented thermistors as self-heating/wind sensing devices. The dc supply voltage was correlated with the air temperature sub-ranges (RCV). The power save mode such as 30s self-heating/5 min pause was used to measure the thermistor response on stable wind blow. The three-axis' anemometer was formed using five sensor devices placed in five holes drilled in the cubical piece of thermally insulating material: three thermistor sensors measure wind speed on the x, y, z - axes, the fourth sensor Pt 1000 measures the air temperature T, while the fifth sensor (capacitive type) measures humidity H. The obtained sensitivity and inaccuracy were compared with respective ones of other anemometers

Bowen Ratio Energy Balance Measurement of Carbon Dioxide (CO2) Fluxes of No-Till and Conventional Tillage Agriculture in Lesotho

Global food demand requires that soils be used intensively for agriculture, but how these soils are managed greatly impacts soil fluxes of carbon dioxide (CO2). Soil management practices can cause carbon to be either sequestered or emitted, with corresponding uncertain influence on atmospheric CO2 concentrations. The situation is further complicated by the lack of CO2 flux measurements for African subsistence farms. For widespread application in remote areas, a simple experimental methodology is desired. As a first step, the present study investigated the use of Bowen Ratio Energy Balance (BREB) instrumentation to measure the energy balance and CO2 fluxes of two contrasting crop management systems, till and no-till, in the lowlands within the mountains of Lesotho. Two BREB micrometeorological systems were established on 100-m by 100-m sites, both planted with maize (Zea mays) but under either conventional (plow, disk-disk) or no-till soil mangement systems. The results demonstrate that with careful maintenance of the instruments by appropriately trained local personnel, the BREB approach offers substantial benefits in measuring real time changes in agroecosystem CO2 flux. The periods where the two treatments could be compared indicated greater CO2 sequestration over the no-till treatments during both the growing and non-growing seasons

Air Temperature Comparison between the MMTS and the USCRN Temperature Systems

A new U.S. Climate Reference Network (USCRN) was officially and nationally commissioned by the Department of Commerce and the National Oceanic and Atmospheric Administration in 2004. During a 1-yr side-by-side field comparison of USCRN temperatures and temperatures measured by a maximum-minimum temperature system (MMTS), analyses of hourly data show that the MMTS temperature performed with biases: 1) a systematic bias–ambient-temperature-dependent bias and 2) an ambient-solar-radiation- and ambient-wind- speed-dependent bias. Magnitudes of these two biases ranged from a few tenths of a degree to over 1C compared to the USCRN temperatures. The hourly average temperatures for the USCRN were the dependent variables in the development of two statistical models that remove the biases due to ambient temperature, ambient solar radiation, and ambient wind speed in the MMTS. The model performance was examined, and the results show that the adjusted MMTS data were substantially improved with respect to both systematic bias and the bias associated with ambient solar radiation and ambient wind speed. In addition, the results indicate that the historical temperature datasets prior to the MMTS era need to be further investigated to produce long-term homogenous times series of area-average temperature

The performance of NASA research hydrogen masers

Field operable hydrogen masers based on prior maser designs are presented. These units incorporate improvements in magnetic shielding, lower noise electronics, better thermal control, and have a microprocessor for operation, monitoring, and diagnostic functions. They are ruggedly built for transportability and ease of service anywhere in the world

Infrared sky noise study

The hardware and techniques to measure and compare sky noise at several sites were studied, and a device was developed that would maximize its output and minimize its output for modulation. The instrument and its functions are described. The nature of sky emissions and the fluctuation, gaseous sources of sky noise, and aerosol sources are discussed. It is concluded that sky noise really exists, and the spatial distribution of the sky noise sources are such that observed noise values are linear functions of chopping stroke