HYDRAULIC WIND POWER DROOP ANALYSIS

poster abstractThe power transferred from the wind turbine to the generator is im-portant to keep the systems active, power balance and droop frequency con-trol when connected to a network. This is important to ensure maximum power output obtained from wind velocity. When there is a change present in the real power demand at a point in the network, it is reflected throughout the system by fluctuation in frequency. If a drop in frequency occurs the generator will decelerate at a rate determined by the moment of inertia plus all the masses connected to its shaft. This results in the conversion of kinet-ic energy of the generator to electrical energy thus giving a power surge. If there is an increase in the system frequency, the inverse is true. Hydraulic wind power provides opportunities for multiple wind turbine energy collection and central generation. The system has many benefits over direct driver counterparts including simple structure and opportunities for energy storage units. However, as the system relies on hydraulic connection of wind turbine and generators, it exhibits a nonlinear power and speed characteristics. This poster will analyze the effect of increasing the hydraulic wind turbines on the droop characteristics of the system. Several wind speeds and loading conditions have determined that adding wind turbines to the hydraulic energy transfer system will increase the frequency stability of the system. Some of the hydraulic prime mover characteristics will be identi-fied through experimental results from our prototype in Dr. Izadian’s labora-tory. This research was supported by IUPUI Solution Center

Power Droop Reduction In Logic BIST By Scan Chain Reordering

Significant peak power (PP), thus power droop (PD), during test is a serious concern for modern, complex ICs. In fact, the PD originated during the application of test vectors may produce a delay effect on the circuit under test signal transitions. This event may be erroneously recognized as presence of a delay fault, with consequent generation of an erroneous test fail, thus increasing yield loss. Several solutions have been proposed in the literature to reduce the PD during test of combinational ICs, while fewer approaches exist for sequential ICs. In this paper, we propose a novel approach to reduce peak power/power droop during test of sequential circuits with scan-based Logic BIST. In particular, our approach reduces the switching activity of the scan chains between following capture cycles. This is achieved by an original generation and arrangement of test vectors. The proposed approach presents a very low impact on fault coverage and test time

Scalable Approach for Power Droop Reduction During Scan-Based Logic BIST

The generation of significant power droop (PD) during at-speed test performed by Logic Built-In Self Test (LBIST) is a serious concern for modern ICs. In fact, the PD originated during test may delay signal transitions of the circuit under test (CUT): an effect that may be erroneously recognized as delay faults, with consequent erroneous generation of test fails and increase in yield loss. In this paper, we propose a novel scalable approach to reduce the PD during at-speed test of sequential circuits with scan-based LBIST using the launch-on-capture scheme. This is achieved by reducing the activity factor of the CUT, by proper modification of the test vectors generated by the LBIST of sequential ICs. Our scalable solution allows us to reduce PD to a value similar to that occurring during the CUT in field operation, without increasing the number of test vectors required to achieve a target fault coverage (FC). We present a hardware implementation of our approach that requires limited area overhead. Finally, we show that, compared with recent alternative solutions providing a similar PD reduction, our approach enables a significant reduction of the number of test vectors (by more than 50%), thus the test time, to achieve a target FC

Stability Bounds of Droop-Controlled Inverters in Power Grid Networks

The energy mix of future power systems will include high shares of electricity generation by wind turbines and solar photovoltaics. These generation facilities are generally connected via power-electronic inverters. While conventional generation responds dynamically to the state of the electric power system, inverters are power-electronic hardware and need to be programmed to react to the state of the system. Choosing an appropriate control scheme and the corresponding parameters is necessary to guarantee that the system operates safely. A prominent control scheme for inverters is droop control, which mimics the response of conventional generation. In this work, we investigate the stability of coupled systems of droop-controlled inverters in arbitrary network topologies. Employing linear stability analysis, we derive effective local stability criteria that consider both the overall network topology as well as its interplay with the inverters’ intrinsic parameters. First, we explore the stability of an inverter coupled to an infinite grid and uncover stability and instability regions. Second, we extend the analysis to a generic topology of inverters and provide mathematical criteria for the stability and instability of the system. Last, we showcase the usefulness of the criteria by examining two model systems using numerical simulations. The developed criteria show which parameters might lead to an unstable operating state.Stability Bounds of Droop-Controlled Inverters in Power Grid NetworkspublishedVersio

Control of multi-terminal HVDC networks towards wind power integration: A review

© 2015 Elsevier Ltd. More interconnections among countries and synchronous areas are foreseen in order to fulfil the EU 2050 target on the renewable generation share. One proposal to accomplish this challenging objective is the development of the so-called European SuperGrid. Multi-terminal HVDC networks are emerging as the most promising technologies to develop such a concept. Moreover, multi-terminal HVDC grids are based on highly controllable devices, which may allow not only transmitting power, but also supporting the AC grids to ensure a secure and stable operation. This paper aims to present an overview of different control schemes for multi-terminal HVDC grids, including the control of the power converters and the controls for power sharing and the provision of ancillary services. This paper also analyses the proposed modifications of the existing control schemes to manage high participation shares of wind power generation in multi-terminal grids.Postprint (author's final draft