Soft, comfortable polymer dry electrodes for high quality ECG and EEG recording

Conventional gel electrodes are widely used for biopotential measurements, despite important drawbacks such as skin irritation, long set-up time and uncomfortable removal. Recently introduced dry electrodes with rigid metal pins overcome most of these problems; however, their rigidity causes discomfort and pain. This paper presents dry electrodes offering high user comfort, since they are fabricated from EPDM rubber containing various additives for optimum conductivity, flexibility and ease of fabrication. The electrode impedance is measured on phantoms and human skin. After optimization of the polymer composition, the skin-electrode impedance is only similar to 10 times larger than that of gel electrodes. Therefore, these electrodes are directly capable of recording strong biopotential signals such as ECG while for low-amplitude signals such as EEG, the electrodes need to be coupled with an active circuit. EEG recordings using active polymer electrodes connected to a clinical EEG system show very promising results: alpha waves can be clearly observed when subjects close their eyes, and correlation and coherence analyses reveal high similarity between dry and gel electrode signals. Moreover, all subjects reported that our polymer electrodes did not cause discomfort. Hence, the polymer-based dry electrodes are promising alternatives to either rigid dry electrodes or conventional gel electrodes

Modelling Dynamically Re-sizeable Electrodes (DRE) for Targeted Transcutaneous Measurements in Impedance Plethysmography

Impedance plethysmography of extremities typically uses band electrodes around limbs to monitor changes in blood volume. This often causes monitored blood variations to only generate minuscule impedance values relative to the measured baseline, attributed to the tissue surrounding the artery or vein of interest. Smaller, ECG type electrodes can provide a larger signal, however their output is very easily affected by the placement of the electrodes relative to the targeted vasculature. This paper presents a novel method to adjust the active surface of electrodes, introducing Dynamically Re-sizeable Electrodes (DRE), to only target the exact area of interest, forming localised electrodes, without having to manually re-position them. Elongated rectangular electrodes were partitioned into smaller electrode segments, interconnected through custom circuitry. For the development and assessment of the DRE system, work was carried out both experimentally in-vitro on gelatine phantoms using custom switching circuits and through finite element modelling (FEM) simulations in COMSOL. A scanning sequence made use of DRE in single segment variable tetra-pole (SSVT) mode proved capable to identify the transcutaneous location of the blood vessel of interest and the specific electrode segments located in its vicinity. Impedance measurements were then taken using these segments connected to form localised electrodes only placed over the targeted vessel. The resulting localised electrodes exhibited up to 28% increased sensitivity to blood variations relative to larger electrodes

Characterization of the Plasma Shape of the TIG Welding Arc

Tungsten electrodes were prepared to analyse the plasma geometry at TIG welding. The investigated electrodes were La02, Th02 alloyed. Tip flatted electrodes were grinded as well. The shape of plasma were analysed for 36 different electrodes. Analysing of digital pictures, the plasma geometry were measured. Whole and brightest plasma area was checked as well. Measured values were represented as a function of taper angles. Main conclusion is that the maximum of the diagrams, which characterise the effect of taper angle for sharpened electrodes, were at taper angle of 20-30°. The properties of the red and the black electrodes are running collaterally. Despite of them the characteristics of the gold electrode shift to higher taper angles causing by the high La02 content of the electrode. There was no clear correlation between the electrode taper angle and the shape characteristics of plasma for the electrodes, which were prepared with a flat tip

Microwave field effect transistor

Electrodes of a high power, microwave field effect transistor are substantially matched to external input and output networks. The field effect transistor includes a metal ground plane layer, a dielectric layer on the ground plane layer, a gallium arsenide active region on the dielectric layer, and substantially coplanar spaced source, gate, and drain electrodes having active segments covering the active region. The active segment of the gate electrode is located between edges of the active segments of the source and drain electrodes. The gate and drain electrodes include inactive pads remote from the active segments. The pads are connected directly to the input and output networks. The source electrode is connected to the ground plane layer. The space between the electrodes and the geometry of the electrodes extablish parasitic shunt capacitances and series inductances that provide substantial matches between the input network and the gate electrode and between the output network and the drain electrode. Many of the devices are connected in parallel and share a common active region, so that each pair of adjacent devices shares the same source electrodes and each pair of adjacent devices shares the same drain electrodes. The gate electrodes for the parallel devices are formed by a continuous stripe that extends between adjacent devices and is connected at different points to the common gate pad

Properties of Ag/AgCl electrodes fabricated with IC-compatible technologies

The purpose of this work is to fabricate and characterize Ag/AgCl electrodes made on a silicon chip at the wafer level with integrated circuit-compatible fabrication techniques. Such electrodes are useful as reference electrodes in several kinds of chemical sensors. Two types of electrode were investigated. The first type uses an evaporated AgCl layer that is patterned with lift-off photolithography. The second type is formed by exposing a selected part of the silver substrate to a KCrO3Cl solution. Both types of electrode give the thermodynamically expected potential response to variations of Cl− ion concentration. The potential generated by the KCrO3Cl-formed electrodes was more stable, however. Auger electron spectroscopy depth profiles indicate that immersion in a KCrO3Cl solution produces a thin layer of AgCl on top of a layer of AgO. The low electronic resistance of AgO then reduces the measured series resistance of the KCrO3Cl-formed electrodes. Impedance plane plots and the impedance as a function of frequency were measured for both types of electrode, and the impedance of the evaporated AgCl electrodes was indeed considerably higher. The impedance measurements could be successfully modelled by assuming a Randles equivalent circuit for the AgCl/electrolyte interface. For the KCrO3Cl-formed electrodes, the impedance was modified by the porosity these electrodes manifested

Intraneural stimulation using 2D wire-microelectrode arrays: I. Experimental results

A two-dimensional 24-channel wire-microelectrode array was inserted into the peroneal nerve of the rat during acute experiments. The electrodes in the array are on a regular grid of 6 by 4 electrodes; inter-electrode spacing is 120 ¿m. For each of the electrodes in the array the corresponding twitch-force recruitment curve was recorded from the extensor digitorum longus muscle (EDL). A complete set of 24 recruitment curves is presented The shape of the recruitment curves varies among the electrodes in the array. This supports previous findings which suggest a different motor unit recruitment order for stimulating electrodes at different intraneural position

Further developments and tests of microstrip gas counters with resistive electrodes

We present results from further tests of Microstrip Gas Counters (MSGCs) with resistive electrodes. The maim advantage of this detector is that it is spark-protected: in contrast to "classical" MSGCs with metallic electrodes, sparks in this new detector do not destroy its electrodes. As a consequence the MSGC with resistive electrodes is more reliable in operation which may open new avenues in applications. One of them which is under investigation now is the use of Resistive electrodes MSGC (R-MSGC) as photodetector in some particular designs of noble liquid dark matter detectors.Comment: Presented at the RD-51 mini-week at CERN, January 17, 201

Vapor-deposited platinum as a fuel-cell catalyst

Electrodes are prepared by vacuum deposition of platinum on nickel substrate with conventional vapor-deposition apparatus. Amount of platinum loaded on substrate can be veried by changing exposure time during deposition. These electrodes are significantly more effective than conventional oxygen electrodes

Photoelectrochemical electrodes

The surface of a moderate band gap semiconductor such as p-type molybdenum sulfide is modified to contain an adherent film of charge mediating ionene polymer containing an electroactive unit such as bipyridimium. Electron transport between the electrode and the mediator film is favorable and photocorrosion and recombination processes are suppressed. Incorporation of particles of catalyst such as platinum within the film provides a reduction in overvoltage. The polymer film is readily deposited on the electrode surface and can be rendered stable by ionic or addition crosslinking. Catalyst can be predispersed in the polymer film or a salt can be impregnated into the film and reduced therein

Cobalt improves nickel hydroxide electrodes for batteries

Positive nickel hydroxide electrodes containing 20 mole percent of cobalt hydroxide are more efficient than when impregnated to the same degree by weight with nickel hydroxide alone. Charge-acceptance and oxygen-evolution tests indicate cobalt electrodes are more efficient than plain positive nickel hydroxide electrodes at all rates of charge