4,931 research outputs found

    Structural analysis of three space crane articulated-truss joint concepts

    Get PDF
    Three space crane articulated truss joint concepts are studied to evaluate their static structural performance over a range of geometric design parameters. Emphasis is placed on maintaining the four longeron reference truss performance across the joint while allowing large angle articulation. A maximum positive articulation angle and the actuator length ratio required to reach the angle are computed for each concept as the design parameters are varied. Configurations with a maximum articulation angle less than 120 degrees or actuators requiring a length ratio over two are not considered. Tip rotation and lateral deflection of a truss beam with an articulated truss joint at the midspan are used to select a point design for each concept. Deflections for one point design are up to 40 percent higher than for the other two designs. Dynamic performance of the three point design is computed as a function of joint articulation angle. The two lowest frequencies of each point design are relatively insensitive to large variations in joint articulation angle. One point design has a higher maximum tip velocity for the emergency stop than the other designs

    A comparison of two trusses for the space station structure

    Get PDF
    The structural performance of two truss configurations, the orthogonal tetrahedral and a Warren-type, are compared using finite element models representing the November Reference Phase 1 Space Station. The truss torsional stiffness properties and fundamental torsion frequency are determined using cantilever truss-beam models. Frequencies, mode shapes, transient response, and truss strut compressive loads are compared for the two space station models. The performance benefit resulting from using a high modulus truss strut is also presented. Finally, assembly and logistics characteristics of the two truss configurations are evaluated

    GRAIL – Grid Access and Instrumentation Tool

    Get PDF
    Since the release of Globus Toolkit 4 Web services enrich the world of Grid Computing. They provide methods to develop modular Grid applications which can be parallelized easily. The access to Web services is mostly solved by complex command line tools which need a good deal of knowledge of the underlaying Grid technologies. GRAIL is intended to fill the gap between existing Grid access methods and both the developer who wants to utilize the Grid for own developments and the user who wants to access the Grid without much additional knowledge. It simplifies the access and the testing of Web services for the Globus Grid middleware. GRAIL provides an easy to use graphical user interface for executing Web services and enables the user to construct complex relationships between services to realize parallel execution. The underlying framework allows an easy integration of any Web service or other arbitrary task without much additional effort for the developer. Existing technologies, shipped with the Globus Toolkit, are seamlessly integrated into GRAIL

    Parametric infrared tunable laser system

    Get PDF
    A parametric tunable infrared laser system was built to serve as transmitter for the remote detection and density measurement of pollutant, poisonous, or trace gases in the atmosphere. The system operates with a YAG:Nd laser oscillator amplifier chain which pumps a parametric tunable frequency converter. The completed system produced pulse energies of up to 30 mJ. The output is tunable from 1.5 to 3.6 micrometers at linewidths of 0.2-0.5 /cm (FWHM), although the limits of the tuning range and the narrower line crystals presently in the parametric converter by samples of the higher quality already demonstrated is expected to improve the system performance further

    A Correlation Between Hard Gamma-ray Sources and Cosmic Voids Along the Line of Sight

    Full text link
    We estimate the galaxy density along lines of sight to hard extragalactic gamma-ray sources by correlating source positions on the sky with a void catalog based on the Sloan Digital Sky Survey (SDSS). Extragalactic gamma-ray sources that are detected at very high energy (VHE; E>100 GeV) or have been highlighted as VHE-emitting candidates in the Fermi Large Area Telescope hard source catalog (together referred to as "VHE-like" sources) are distributed along underdense lines of sight at the 2.4 sigma level. There is also a less suggestive correlation for the Fermi hard source population (1.7 sigma). A correlation between 10-500 GeV flux and underdense fraction along the line of sight for VHE-like and Fermi hard sources is found at 2.4 sigma and 2.6 sigma, respectively. The preference for underdense sight lines is not displayed by gamma-ray emitting galaxies within the second Fermi catalog, containing sources detected above 100 MeV, or the SDSS DR7 quasar catalog. We investigate whether this marginal correlation might be a result of lower extragalactic background light (EBL) photon density within the underdense regions and find that, even in the most extreme case of a entirely underdense sight line, the EBL photon density is only 2% less than the nominal EBL density. Translating this into gamma-ray attenuation along the line of sight for a highly attenuated source with opacity tau(E,z) ~5, we estimate that the attentuation of gamma-rays decreases no more than 10%. This decrease, although non-neglible, is unable to account for the apparent hard source correlation with underdense lines of sight.Comment: Accepted by MNRA

    Oblique stacking of three-dimensional dome islands in Ge/Si multilayers

    Get PDF
    The organization of Ge "dome" islands in Ge/Si multilayers has been investigated by cross-sectional transmission electron microscopy. Ge domes are found to spontaneously arrange in oblique stacks, replicating at a well-defined angle from one bilayer to the next. The formation of oblique island stacks is governed by a complex interplay of surface strain, generated by the already buried islands, and surface curvature, caused by the inherent tendency of large domes to carve out material from the surrounding planar substrate. (C) 2001 American Institute of Physics

    Resection of palatal tumours with the CO2 laser

    Get PDF
    On the basis of the authors' experience with 20 patients, CO2 laser resection of palatal tumours has proved to be a good alternative to conventional surgical resection. The CO2 laser beam permits precise resection, due to only slight intra-operative bleeding coupled with use of the operating microscope. Wound healing is good and post-operative pain remarkably littl

    Multidisciplinary analysis of actively controlled large flexible spacecraft

    Get PDF
    The control of Flexible Structures (COFS) program has supported the development of an analysis capability at the Langley Research Center called the Integrated Multidisciplinary Analysis Tool (IMAT) which provides an efficient data storage and transfer capability among commercial computer codes to aid in the dynamic analysis of actively controlled structures. IMAT is a system of computer programs which transfers Computer-Aided-Design (CAD) configurations, structural finite element models, material property and stress information, structural and rigid-body dynamic model information, and linear system matrices for control law formulation among various commercial applications programs through a common database. Although general in its formulation, IMAT was developed specifically to aid in the evaluation of the structures. A description of the IMAT system and results of an application of the system are given

    Structurally adaptive space crane concept for assembling space systems on orbit

    Get PDF
    Many future human space exploration missions will probably require large vehicles that must be assembled on orbit. Thus, a device that can move, position, and assemble large and massive spacecraft components on orbit becomes essential for these missions. A concept is described for such a device: a space crane concept that uses erectable truss hardware to achieve high-stiffness and low-mass booms and uses articulating truss joints that can be assembled on orbit. The hardware has been tested and shown to have linear load-deflection response and to be structurally predictable. The hardware also permits the crane to be reconfigured into different geometries to satisfy future assembly requirements. A number of articulating and rotary joint concepts have been sized and analyzed, and the results are discussed. Two strategies were proposed to suppress motion-induced vibration: placing viscous dampers in selected truss struts and preshaping motion commands. Preliminary analyses indicate that these techniques have the potential to greatly enhance structural damping
    corecore