Environmentally conscious consumption patterns in Hungarian households

This article provides a comprehensive review of the literature on the theoretical aspects of sustainable consumption. The conditions for consumers’ social responsibility and the formation of environmentally conscious behavior patterns will also be discussed, along with possible methods for motivating behavioral changes. The authors have completed a primary research study with the purpose of surveying environmentally conscious consumption patterns in Hungary. They also examined how the provision of appropriate information and the raising of awareness might encourage sustainable consumption. According to their findings, the respondents’ knowledge on environmentally conscious behavior was rather limited, and reinforcement was needed in identifying appropriate activity alternatives. This paper provides a summary of the qualitative research phase which employed in-depth interviews, logging and focus groups. The consecutive application of these methods enabled the authors to keep track of the process and the consequences of raising awareness

Experimental Fracture Model versus Osteotomy Model in Metacarpal Bone Plate Fixation

Introduction. Osteotomy or fracture models can be used to evaluate mechanical properties of fixation techniques of the hand skeleton in vitro. Although many studies make use of osteotomy models, fracture models simulate the clinical situation more realistically. This study investigates monocortical and bicortical plate fixation on metacarpal bones considering both aforementioned models to decide which method is best suited to test fixation techniques. Methods. Porcine metacarpal bones (n = 40) were randomized into 4 groups. In groups I and II bones were fractured with a modified 3-point bending test. The intact bones represented a further control group to which the other groups after fixation were compared. In groups III and IV a standard osteotomy was carried out. Bones were fixated with plates monocortically (group I, III) and bicortically (group II, IV) and tested for failure. Results. Bones fractured at a mean maximum load of 482.8 N ± 104.8 N with a relative standard deviation (RSD) of 21.7%, mean stiffness was 122.3 ± 35 N/mm. In the fracture model, there was a significant difference (P = 0.01) for maximum load of monocortically and bicortically fixed bones in contrast to the osteotomy model (P = 0.9). Discussion. In the fracture model, because one can use the same bone for both measurements in the intact state and the bone-plate construct states, the impact of inter-individual differences is reduced. In contrast to the osteotomy model there are differences between monocortical and bicortical fixations in the fracture model. Thus simulation of the in vivo situation is better and seems to be suitable for the evaluation of mechanical properties of fixation techniques on metacarpals

Optimization of Material Contrast for Efficient FIB‐SEM Tomography of Solid Oxide Fuel Cells

Focused ion beam (FIB) – scanning electron microscopy (SEM) serial sectioning tomography has become an important tool for three‐dimensional microstructure reconstruction of solid oxide fuel cells (SOFC) to obtain an understanding of fabrication‐related effects and SOFC performance. By sequential FIB milling and SEM imaging a stack of cross‐section images across all functional SOFC layers was generated covering a large volume of 3.5·10$^{4}$ μm$^{3}$. One crucial step is image segmentation where regions with different image intensities are assigned to different material phases within the SOFC. To analyze all relevant SOFC materials, it was up to now mandatory to acquire several images by scanning the same region with different imaging parameters because sufficient material contrast could otherwise not be achieved. In this work we obtained high‐contast SEM images from a single scan to reconstract all functional SOFC layers consisting of a Ni/Y$_{2}$O$_{3}$‐doped ZrO$_{2}$ (YDZ) cermet anode, YDZ electrolyte and (La,Sr)MnO$_{3}$/YDZ cathode. This was possible by using different, simultaneous read‐out detectors installed in a state‐of‐the‐art scanning electron microscope. In addition, we used a deterministic approach for the optimization of imaging parameters by employing Monte Carlo simulations rather than trial‐and‐error tests. We also studied the effect of detection geometry, detecting angle range and detector type

Glycerolysis of Fats and Methyl Esters.

The glycerolysis of methyl esters and triglycerides with crude glycerol. a coproduct from the transesterification of triglycerides, was studied. Three procedures were followed ior this conversion. The first procedure was a one-step glycerolysis with methyl esters. The second procedure was a two-step process. This proced~~irnev olved an initial partial glycerolysis with methyl esters, followed by fat glycerolysis. The third procedure u,as a simultaneous glycerolysis n,ith methyl esters and triglycerides. In the glycerolysis with methyl esters, the removal of methanol is vital to the production of mono- and diglycerides. Methanol was removed either by drawing vacuum on the reactor or by stripping methanol out by means of an inert carrier gas (nitrogen]. Different molar ratios of methyl esters to glycerol were tested in the first two processes. At low concentration of methyi esters, total conversion oi methyl esters to mono- and diglycerides was achieved. As the concentration oi methyl esters was increased, the conversion of methyl esters to mono and diglvcerides was decreased. Furthermore, the ratio of mono- to diglycerides was also higher at lower roncentrations of methyl esters. The conversion of triglycerides in the two-step process with crude glycerol was similar to a one-step fat glycerolysis with pure glycerol. The composition of different coniponents and the ratio of mono to diglycerides were also comparabl

Biomechanical Analysis of the Efficacy of Locking Plates during Cyclic Loading in Metacarpal Fractures

Purpose. To analyse the biomechanical characteristics of locking plates under cyclic loading compared to a nonlocking plate in a diaphyseal metacarpal fracture. Methods. Oblique diaphyseal shaft fractures in porcine metacarpal bones were created in a biomechanical fracture model. An anatomical reduction and stabilization with a nonlocking and a comparable locking plate in mono- or bicortical screw fixation followed. Under cyclic loading, the displacement, and in subsequent load-to-failure tests, the maximum load and stiffness were measured. Results. For the monocortical screw fixation of the locking plate, a similar displacement, maximum load, and stiffness could be demonstrated compared to the bicortical screw fixation of the nonlocking plate. Conclusions. Locking plates in monocortical configuration may function as a useful alternative to the currently common treatment with bicortical fixations. Thereby, irritation of the flexor tendons would be avoided without compromising the stability, thus enabling the necessary early functional rehabilitation

A theoretical insight into the photophysics of psoralen

Psoralen photophysics has been studied on quantum chemistry grounds using the multiconfigurational second-order perturbation method CASPT2. Absorption and emission spectra of the system have been rationalized by computing the energies and properties of the low-lying singlet and triplet excited states. The S1 ππ* state has been determined to be responsible of the lowest absorption and fluorescence bands and to initially carry the population in the photophysical processes related to the phototherapeutic properties of psoralen derivatives. The low-lying T1 ππ* state is, on the other hand, protagonist of the phosphorescence, and its prevalent role in the reactivity of psoralen is suggested to be related to the elongation of the pyrone ring C3–C4 bond, where the spin density is distributed on both carbon atoms. Analysis of energy gaps and spin-orbit coupling elements indicates that the efficient photophysical process leading to the population of the lowest triplet state does not take place at the Franck-Condon region but along the S1 relaxation [email protected] [email protected] [email protected]