Landing-shock Recorder

A description of a special type of seismograph, called a "landing-shock recorder," to be used for measuring the acceleration during impacts such as are experienced in airplane landings, is given . The theory, together with the assumptions made, is discussed in its relation to calculating the acceleration experienced in impact. Calculations are given from records obtained for two impacts of known acceleration. In one case the impact was very severe and in the other it was only moderately severe

Principles involved in the cooling of a finned and baffled cylinder

An analysis of the cooling problems for a finned cylinder is made on the basis of the known fundamental principles of heat transfer from pipes. Experimental results that support the analysis are presented. The results of previous investigations on the problem are evaluated on the basis of the analysis and the results. An illustration of the application of these principles to a specific problem is included

Experimental Investigation of the Robinson-Type Cup Anemometer

This report presents the results of wind tunnel tests on a Robinson-type anemometer. The investigation covered force measurements on individual cups, as well as static and dynamic torque measurements and calibrations on complete cup wheels. In the tests on individual cups 5 cup forms were used and in the measurements on complete cup wheels 4 cup wheels with 3 arm lengths for each cup wheel were tested. All the results are presented in graphical form

Air Flow Around Finned Cylinders

Report presents the results of a study made to determine the air-flow characteristics around finned cylinders. Air-flow distribution is given for a smooth cylinder, for a finned cylinder having several fin spacings and fin widths, and for a cylinder with several types of baffle with various entrance and exit shapes. The results of these tests show: that flow characteristics around a cylinder are not so critical to changes in fin width as they are to fin spacing; that the entrance of the baffle has a marked influence on its efficiency; that properly designed baffles increase the air flow over the rear of the cylinder; and that these tests check those of heat-transfer tests in the choice of the best baffle

The problem of cooling an air-cooled cylinder on an aircraft engine

An analysis of the cooling problem has been to show by what means the cooling of an air-cooled aircraft engine may be improved. Each means of improving cooling is analyzed on the basis of effectiveness in cooling with respect to power for cooling. The altitude problem is analyzed for both supercharged and unsupercharged engines. The case of ground cooling is also discussed. The heat-transfer process from the hot gases to the cylinder wall is discussed on the basis of the fundamentals of heat transfer and thermodynamics. Adiabatic air-temperature rise at a stagnation point in compressible flow is shown to depend only on the velocity of flow

Aerodynamic characteristics of anemometer cups

The static lift and drag forces on three hemispherical and two conical cups were measured over a range of angles of attack from 0 degrees to 180 degrees and a range of Reynolds Numbers from very small up to 400,000. The problems of supporting the cup for measurement and the effect of turbulence were also studied. The results were compared with those of other investigators

Cooling on the Front of an Air-cooled Engine Cylinder in a Conventional Engine Cowling

Measurements were made of the cooling on the fronts of model cylinders in a conventional cowling for cooling in both the ground and the cruising conditions. The mechanisms of front and rear cooling are essentially different. Cooling on the rear baffled part of the cylinders continually increases with increasing fin width. For the front of the cylinder, an optimum fin width was found to exist beyond which an increase in width reduced the heat transfer. The heat transfer coefficient on the front of the cylinders was larger on the side of the cylinder facing the propeller swirl than on the opposite side. This effect became more pronounced as the fin width was increased. These results are introductory to the study of front cooling and show the general effect of several test parameters

Full-Scale Tests of NACA Cowlings

A comprehensive investigation has been carried on with full-scale models in the NACA 20-foot wind tunnel, the general purpose of which is to furnish information in regard to the physical functioning of the composite propeller-nacelle unit under all conditions of take-off, taxiing, and normal flight. This report deals exclusively with the cowling characteristics under condition of normal flight and includes the results of tests of numerous combinations of more than a dozen nose cowlings, about a dozen skirts, two propellers, two sizes of nacelle, as well as various types of spinners and other devices

Characteristics of Six Propellers Including the High-Speed Range

This investigation is part of an extensive experimental study that has been carried out at full scale in the NACA 20-foot tunnel, the purpose of which has been to furnish information in regard to the functioning of the propeller-cowling-nacelle unit under all conditions of take-off, climbing, and normal flight. This report presents the results of tests of six propellers in the normal and high-speed flight range and also includes a study of the take-off characteristics