16,985 research outputs found
Multiple-Access Bosonic Communications
The maximum rates for reliably transmitting classical information over
Bosonic multiple-access channels (MACs) are derived when the transmitters are
restricted to coherent-state encodings. Inner and outer bounds for the ultimate
capacity region of the Bosonic MAC are also presented. It is shown that the
sum-rate upper bound is achievable with a coherent-state encoding and that the
entire region is asymptotically achievable in the limit of large mean input
photon numbers.Comment: 11 pages, 5 figures, corrected two figures, accepted for publication
in Phys. Rev.
Hospital Treatment Rates and Spill-Over Effects: Does Ownership Matter?
This paper studies the effect of hospital ownership on treatment rates allowing for spatial correlation among hospitals. Competition among hospitals and knowledge spillovers generate significant externalities which we try to capture using the spatial Durbin model. Using a panel of 2342 hospitals in the 48 continental states observed over the period 2005 to 2008, we find significant spatial correlation of medical service treatment rates among hospitals. The paper also shows mixed results on the effect of hospital ownership on treatment rates that depends upon the market structure where the hospital is located and which varies by treatment type
Recommended from our members
A New Layer Casting System for Ceramic Laser Rapid Prototyping Apparatus
In the existing Ceramic Laser Fusion system, slurry is fed on the high
temperature surface of the green part; therefore, a part of water infiltrates into the
green block and vaporizes before the process of layer casting. As a result, the slurry
viscosity rises gradually; the quality of the layer surface is not uniform, and the green
part density is uneven. The aim of present study is to develop a new layer casting
system which can solve the problems mentioned above to obtain a green part with
uniform surface quality and density, and to shorten the time-taken of part fabrication.
The first part of the paper illustrates the major requirements and parameters of a slurry
distributor; the second part describes the integration of the slurry feeding device and
layer casting system. The integrated system can feed slurry and cast thin layer
simultaneously; consequently, the drawbacks of the existing system can be eliminated
and the time-taken of the layer casting can be shortened. A variable-frequency drive
(inverter) is used to control the motor speed. The relation between the frequency and
the slurry delivery can be included in the process control program to adjust the
quantity in accordance with the layer thickness; hence, the waste of the slurry can be
reduced.Mechanical Engineerin
Recommended from our members
The Characteristics and Applications of Ceramic Laser Fusion and Ceramic Laser Sintering
The aim of present study is to investigate the possible application of the ceramic parts
which are fabricated with the process of Ceramic Laser Fusion or Ceramic Laser Sintering.
The experimental results reveal: (1) CLF can lead to a reduction in the porosity of the
ceramic part but also can induce micro-cracks. Therefore, this process cannot produce a part
with the required strength by a post-process of infiltration; (2) CLS is capable of fabricating a
ceramic part with high porosity. By adjusting the slurry formulation and varying the scanning
energy, the open porosity can be over 90vol% of the total porosity. After a post-process of
infiltration, the density can be increased to 95%; therefore, CLS can apply to produce a part
with high strength. Because the high open porosity leads to a good permeability, the process
of CLS is suitable for the fabrication of ceramic shell mold.Mechanical Engineerin
Recommended from our members
Prospect of Making Ceramic Shell Mold by Ceramic Laser Fusion
Manufacturing prototypical castings by conventional investment casting not only takes
several weeks, but also is prohibitively expensive. Z Corporation in USA, EOS GmbH and
IPT in Germany employ the techniques of 3DP and SLS respectively to make directly ceramic
shell molds for metal castings. Although those techniques dramatically reduce time
expenditure and production cost, each layer cannot be thinner than 50 µm because of using
powder to pave layers. The dimensional accuracy and roughness of the castings still cannot
meet the specification of precision casting. Therefore, in this paper the ceramic laser fusion
(CLF) was used to pave layers. Each layer can be thinner than 25 µm, so that the step effect
can be diminished and the workpiece surface can be smoother; drying time will be shortened
dramatically. Moreover, the inherent solid-state support formed by green portion has the
capability of preventing upward and downward deformation of the scanned cross sections. In
order to make shell mold which meets the roughness requirement (Rq=3.048µm) of the
precision casting, following issues have to be further studied: (1) design a proper ceramic
shell mold structure, (2) design a paving chamber for paving a complete green layer which
can be easily collapsed, (3) cut down drying time, (4) optimize laser scanning process
parameters with the smallest distortion, (5) eliminate sunken area, (6) reduce layer thickness
to less than13µm, (7) control power to guarantee the energy uniformly absorbed by workpiece,
and (8) develop a method which can directly clean green portion in cavity from gate.Mechanical Engineerin
Definition, analysis and development of an optical data distribution network for integrated avionics and control systems. Part 2: Component development and system integration
Fiber optic transmission is emerging as an attractive concept in data distribution onboard civil aircraft. Development of an Optical Data Distribution Network for Integrated Avionics and Control Systems for commercial aircraft will provide a data distribution network that gives freedom from EMI-RFI and ground loop problems, eliminates crosstalk and short circuits, provides protection and immunity from lightning induced transients and give a large bandwidth data transmission capability. In addition there is a potential for significantly reducing the weight and increasing the reliability over conventional data distribution networks. Wavelength Division Multiplexing (WDM) is a candidate method for data communication between the various avionic subsystems. With WDM all systems could conceptually communicate with each other without time sharing and requiring complicated coding schemes for each computer and subsystem to recognize a message. However, the state of the art of optical technology limits the application of fiber optics in advanced integrated avionics and control systems. Therefore, it is necessary to address the architecture for a fiber optics data distribution system for integrated avionics and control systems as well as develop prototype components and systems
Classical Extended Conformal Algebras Associated with Constrained KP Hierarchy
We examine the conformal property of the second Hamiltonian structure of
constrained KP hierarchy derived by Oevel and Strampp. We find that it
naturallygives a family of nonlocal extended conformal algebras. We give two
examples of such algebras and find that they are similar to Bilal's V algebra.
By taking a gauge transformation one can map the constrained KP hierarchy to
Kuperschmidt's nonstandard Lax hierarchy. We consider the second Hamiltonian
structure in this representation. We show that after mapping the Lax operator
to a pure differential operator the second structure becomes the sum of the
second and the third Gelfand-Dickey brackets defined by this differential
operator. We show that this Hamiltonian structure defines the W-U(1)-Kac-Moody
algebra by working out its conformally covariant form.Comment: NHCU-HEP-94-28, 19 pages (Plain TeX
- …