305 research outputs found
Nonequilibrium entropy production for open quantum systems
We consider open quantum systems weakly coupled to a heat reservoir and
driven by arbitrary time-dependent parameters. We derive exact microscopic
expressions for the nonequilibrium entropy production and entropy production
rate, valid arbitrarily far from equilibrium. By using the two-point energy
measurement statistics for system and reservoir, we further obtain a quantum
generalization of the integrated fluctuation theorem put forward by Seifert
[PRL 95, 040602 (2005)].Comment: 4 pages, 1 figur
Dimensional analysis and Rutherford Scattering
Dimensional analysis, and in particular the Buckingham theorem is
widely used in fluid mechanics. In this article we obtain an expression for the
impact parameter from Buckingham's theorem and we compare our result with
Rutherford's original discovery found in the early twentieth century
Single ion heat engine with maximum efficiency at maximum power
We propose an experimental scheme to realize a nano heat engine with a single
ion. An Otto cycle may be implemented by confining the ion in a linear Paul
trap with tapered geometry and coupling it to engineered laser reservoirs. The
quantum efficiency at maximum power is analytically determined in various
regimes. Moreover, Monte Carlo simulations of the engine are performed that
demonstrate its feasibility and its ability to operate at maximum efficiency of
30% under realistic conditions.Comment: 5 pages, 3 figure
Design and development of low-cost water tunnel for educational purpose
The hydrodynamic behaviour of immersed body is essential in fluid dynamics study. Water tunnel is an example of facility required to provide a controlled condition for fluid flow research. The operational principle of water tunnel is quite similar to the wind tunnel but with different working fluid and higher flow-pumping capacity. Flow visualization in wind tunnel is more difficult to conduct as turbulent flows in wind dissipate quickly whilst water tunnel is more suitable for such purpose due to higher fluid viscosity and wide variety of visualization techniques can be employed. The present work focusses on the design and development of open flow water tunnel for the purpose of studying vortex-induced vibration from turbulent vortex shedding phenomenon. The water tunnel is designed to provide a steady and uniform flow speed within the test section area. Construction details are discussed for development of low-cost water tunnel for quantitative and qualitative fluid flow measurements. The water tunnel can also be used for educational purpose such as fluid dynamics class activity to provide quick access to visualization medium for better understanding of various turbulence motion learnt in class
The Melting Temperature of Liquid Water with the Effective Fragment Potential
The direct simulation of the solid–liquid water interface with the effective fragment potential (EFP) via the constant enthalpy and pressure (NPH) ensemble was used to estimate the melting temperature (Tm) of ice-Ih. Initial configurations and velocities, taken from equilibrated constant pressure and temperature (NPT) simulations at P = 1 atm and T = 305 K, 325 K and 399 K, respectively, yielded corresponding Tm values of 378 ± 16 K, 382 ± 14 K and 384 ± 15 K. These estimates are consistently higher than experiment, albeit to the same degree as previously reported estimates using density functional theory (DFT)-based Born–Oppenheimer simulations with the Becke-Lee–Yang–Parr functional plus dispersion corrections (BLYP-D)
Lattice-Boltzmann model for axisymmetric thermal flows
In this brief report, a thermal lattice-Boltzmann (LB) model is presented for
axisymmetric thermal flows in the incompressible limit. The model is based on
the double-distribution-function LB method, which has attracted much attention
since its emergence for its excellent numerical stability. Compared with the
existing axisymmetric thermal LB models, the present model is simpler and
retains the inherent features of the standard LB method. Numerical simulations
are carried out for the thermally developing laminar flows in circular ducts
and the natural convection in an annulus between two coaxial vertical
cylinders. The Nusselt number obtained from the simulations agrees well with
the analytical solutions and/or the results reported in previous studies.Comment: 11 pages, 4 figure
Developing a Mobile Application‐Based Particle Image Velocimetry Tool for Enhanced Teaching and Learning in Fluid Mechanics: A Design‐Based Research Approach
A robust and intuitive understanding of fluid mechanics—the applied science of fluid motion—is foundational within many engineering disciplines, including aerospace, chemical, civil, mechanical, naval, and ocean engineering. In‐depth knowledge of fluid mechanics is critical to safe and economical design of engineering applications employed globally everyday, such as automobiles, aircraft, and sea craft, and to meeting global 21st century engineering challenges, such as developing renewable energy sources, providing access to clean water, managing the environmental nitrogen cycle, and improving urban infrastructure. Despite the fundamental nature of fluid mechanics within the broader undergraduate engineering curriculum, students often characterize courses in fluid mechanics as mathematically onerous, conceptually difficult, and aesthetically uninteresting; anecdotally, undergraduates may choose to opt‐out of fluids engineering‐related careers based on their early experiences in fluids courses. Therefore, the continued development of new frameworks for engineering instruction in fluid mechanics is needed. Toward that end, this paper introduces mobile instructional particle image velocimetry (mI‐PIV), a low‐cost, open‐source, mobile application‐based educational tool under development for smartphones and tablets running Android. The mobile application provides learners with both technological capability and guided instruction that enables them to visualize and experiment with authentic flow fields in real time. The mI‐PIV tool is designed to generate interest in and intuition about fluid flow and to improve understanding of mathematical concepts as they relate to fluid mechanics by providing opportunities for fluids‐related active engagement and discovery in both formal and informal learning contexts
Energy consumption and capacity utilization of galvanizing furnaces
An explicit equation leading to a method for improving furnace efficiency is presented. This equation is dimensionless and can be applied to furnaces of any size and fuel type for the purposes of comparison. The implications for current furnace design are discussed. Currently the technique most commonly used to reduce energy consumption in galvanizing furnaces is to increase burner turndown. This is shown by the analysis presented here actually to worsen the thermal efficiency of the furnace, particularly at low levels of capacity utilization. Galvanizing furnaces are different to many furnaces used within industry, as a quantity of material (in this case zinc) is kept molten within the furnace at all times, even outside production periods. The dimensionless analysis can, however, be applied to furnaces with the same operational function as a galvanizing furnace, such as some furnaces utilized within the glass industry. © IMechE 2004
Steam consumption minimization using genetic algorithm optimization method: an industrial case study
yesCondensate stabilization is a process where hydrocarbon condensate recovered from natural gas reservoirs is processed to meet the required storage, transportation, and export specifications. The process involves stabilizing of hydrocarbon liquid by separation of light hydrocarbon such as methane from the heavier hydrocarbon constituents such as propane. An industrial scale back-up condensate stabilization unit was simulated using Aspen HYSYS software and validated with the plant data. The separation process consumes significant amount of energy in form of steam. The objectives of the paper are to find the minimum steam consumption of the process and conduct sensitivity and exergy analyses on the process. The minimum steam consumption was found using genetic algorithm optimization method for both winter and summer conditions. The optimization was carried out using MATLAB software coupled with Aspen HYSYS software. The optimization involves six design variables and four constraints, such that realistic results are achieved. The results of the optimization show that savings in steam consumption is 34% as compared to the baseline process while maintaining the desired specifications. The effect of natural gas feed temperature has been investigated. The results show that steam consumption is reduced by 46% when the natural gas feed temperature changes from 17.7 to 32.7°C. Exergy analysis shows that exergy destruction of the optimized process is 37% less than the baseline process
- …