Low background techniques for the SuperNEMO experiment

SuperNEMO is a 0uββ experiment aiming to reach a half-life sensi¬tivity of 1026 years corresponding to an effective Majorana neutrino mass of (mββ) < 50 - 100 meV. Stringent radio-purity constraints are therefore placed on the detector construction material as well as the gases used in the central detector tracking volume. Radon, 222Rn, is one of the most problematic backgrounds for SuperNEMO due to its decay daughter, 214Bi, having a high Qββ value. Hence the radon level within the SuperNEMO tracker gas mixture must not exceed 150 pBq/m3. This activity is beyond the measurement capability of standard radon detectors, therefore a “Radon Concentration Line” was designed and constructed. This instrument has demonstrated the ability to measure the SuperNEMO tracker gas to a sensitivity of 20 pBq/m3. For large volume of gases the 222Rn activity can be measured with a sensitivity of <5 pBq/m3. Measurements of the fully instrumented quarter trackers and its subsystems have been performed. Radon emanation chambers have also been built to be used with the electrostatic detector which has demonstrated sensitivities of <190 pBq. High-purity germanium detectors offer a standard method to mea-sure material contamination. A dedicated screening facility has been established at Boulby Underground Laboratory with four detectors fully commissioned for low background material measurements. Such a detector can be used to make a highly sensitive measurement of 96Zr decay to the 0+ 1 excited state. Simulations of an experimental setup using 20 kg of 96Zr have shown a sensitivity of 1021yrs can be achieved with a 1 year measurement, a factor of 3 improvement on current world’s best limit

Influences of processing technique on electrical characteristics of TVS used in communication systems

An improved technique is proposed in fabricating a semiconductor surge protection device which is used in high-speed wideband information transmission systems. In order to increase the surge handling capability of the device, a double p-type diffusion is used. Specifically, in the diffusion step of gallium, SiO2 is used as a mask to obtain a very small base width and to avoid the reduction of carrier lifetime. It is found that this is a very useful way to reduce the on-state voltage drop and therefore the energy dissipation of the device.published_or_final_versio

Precise Sm-Nd and U-Pb isotopic dating of the supergiant Shizhuyuan polymetallic deposit and its host granite, SE China

The supergiant Shizhuyuan W-Sn-Bi-Mo deposit is hosted by the Qianlishan granite, a small, highly fractionated granitic pluton (~10 km2) with multiple phases of intrusions within the Early Yanshanian granitoid province of SE China. Strong alteration of skarn and greisen that formed in the contact zone between the first and second phases of granite intrusions and Devonian limestone is responsible for the polymetallic mineralizations. SHRIMP U-Pb zircon analysis indicates that the two early phases of the Qianlishan granite formed contemporaneously at 152 ± 2 Ma. Metasomatic minerals (garnet, fluorite and wolframite) separated from the skarn and greisen yield a Sm-Nd isochron age of 149 ± 2 Ma that is interpreted as the formation age of the Shizhuyuan deposit. Therefore, the mineralization of the supergiant Shizhuyuan polymetallic deposit formed contemporaneously with, or very shortly after, the intrusion of the small, highly fractionated Qianlishan granite. © 2004 Cambridge University Press.published_or_final_versio

C-Reactive Protein Promotes Diabetic Kidney Disease in db/db Mice via the CD32b-Smad3-mTOR signaling Pathway

published_or_final_versio

Revealing microstructural evolutions, mechanical properties and wear performance of wire arc additive manufacturing homogeneous and heterogeneous NiTi alloy

Heterogeneous microstructure designs have attracted a great deal of attention, not only because they have the potential to achieve an ideal combination of two conflicting properties, but also because the processes involved in their fabrication are cost-effective and can be scaled up for industrial production. The process parameters in the preparation process have an important effect on the microstructure and properties of alloy members prepared by wire arc additive manufacturing (WAAM) technology. It was expected that the spatial heterogeneous microstructure with large microstructural heterogeneities in metals can be formed through changing the process parameters. In this work, homogeneous NiTi thin-walled component and heterogeneous NiTi thin-walled component were fabricated using WAAM technology by adjusting the heat input. The effects of deposition height and heat input on the microstructure, mechanical properties and wear properties of WAAM NiTi alloys were investigated. The results show that grains were gradually refined with the increase of deposition height in the homogeneous WAAM NiTi component. The ultimate tensile strength of homogeneous WAAM NiTi component increased from 606.87 MPa to 654.45 MPa and the elongation increased from 12.72% to 15.38%, as the increase of deposition height. Moreover, the homogeneous WAAM NiTi component exhibited excellent wear resistance, the coefficient of friction decreased from 0.760 to 0.715 with the increase of deposition height. Meanwhile, the grains in the heterogeneous WAAM NiTi component shows the finest grains in the central region. The ultimate tensile strength of the lower region, middle region and upper region of heterogeneous WAAM NiTi components were 556.12 MPa, 599.53 MPa and 739.79 MPa, and the elongations were 12.98%, 16.69%, 21.74%, respectively. The coefficient of friction for the lower region, middle region and upper region of heterogeneous WAAM NiTi components were 0.713, 0.720 and 0.710, respectively. The microhardness and cyclic compression properties of the homogeneous components with higher heat input were better than those of the heterogeneous components for the same deposition height. The tensile yield strength, elongation and wear resistance of the heterogeneous components were superior compared to the homogeneous components. These results can be used to optimize the WAAM process parameters to prepare NiTi components with excellent mechanical properties

Low-background gamma spectroscopy at the Boulby Underground Laboratory

The Boulby Underground Germanium Suite (BUGS) comprises three low-background, high-purity germanium detectors operating in the Boulby Underground Laboratory, located 1.1 km underground in the north-east of England, UK. BUGS utilises three types of detector to facilitate a high-sensitivity, high-throughput radio-assay programme to support the development of rare-event search experiments. A Broad Energy Germanium (BEGe) detector delivers sensitivity to low-energy gamma-rays such as those emitted by 210 Pb and 234 Th. A Small Anode Germanium (SAGe) well-type detector is employed for efficient screening of small samples. Finally, a standard p-type coaxial detector provides fast screening of standard samples. This paper presents the steps used to characterise the performance of these detectors for a variety of sample geometries, including the corrections applied to account for cascade summing effects. For low-density materials, BUGS is able to radio-assay to specific activities down to 3.6mBqkg −1 for 234 Th and 6.6mBqkg −1 for 210 Pb both of which have uncovered some significant equilibrium breaks in the 238 U chain. In denser materials, where gamma-ray self-absorption increases, sensitivity is demonstrated to specific activities of 0.9mBqkg −1 for 226 Ra, 1.1mBqkg −1 for 228 Ra, 0.3mBqkg −1 for 224 Ra, and 8.6mBqkg −1 for 40 K with all upper limits at a 90% confidence level. These meet the requirements of most screening campaigns presently under way for rare-event search experiments, such as the LUX-ZEPLIN (LZ) dark matter experiment. We also highlight the ability of the BEGe detector to probe the X-ray fluorescence region which can be important to identify the presence of radioisotopes associated with neutron production; this is of particular relevance in experiments sensitive to nuclear recoils

Observation of a ppb mass threshoud enhancement in \psi^\prime\to\pi^+\pi^-J/\psi(J/\psi\to\gamma p\bar{p}) decay

The decay channel $\psi^\prime\to\pi^+\pi^-J/\psi(J/\psi\to\gamma p\bar{p})$ is studied using a sample of $1.06\times 10^8$ $\psi^\prime$ events collected by the BESIII experiment at BEPCII. A strong enhancement at threshold is observed in the $p\bar{p}$ invariant mass spectrum. The enhancement can be fit with an $S$-wave Breit-Wigner resonance function with a resulting peak mass of $M=1861^{+6}_{-13} {\rm (stat)}^{+7}_{-26} {\rm (syst)} {\rm MeV/}c^2$ and a narrow width that is $\Gamma<38 {\rm MeV/}c^2$ at the 90% confidence level. These results are consistent with published BESII results. These mass and width values do not match with those of any known meson resonance.Comment: 5 pages, 3 figures, submitted to Chinese Physics