Spotify tailoring for promoting effectiveness in cross-functional autonomous squads

Organisations tend to tailor agile methods to scale employed practices to have cross-functional autonomous teams while promoting sustainable creative and productive development at a constant pace. Thus, it is important to investigate how organisations tailor agile practices to get the balance right between teams' autonomy and alignment. Spotify model is originally introduced to facilitate the development of music streaming services in a very large-scale project with a Business-to-Consumer (B2C) model. However, developing a large-scale mission-critical project with a Business-to-Business (B2B) model is not essentially supported by the Spotify model. Thus, embracing Spotify model for such projects should be concerned about the question of how Spotify practices are adjusted to promote the effectiveness of cross-functional autonomous squads in a mission-critical project with B2B model? In this paper, we conduct a longitudinal embedded case study, which lasted 21 months during which 14 semi-structured interviews were conducted. The Grounded Theory (GT) is adopted to analyse the collected data. As a result, we identify practices and processes that promote effectiveness in cross-functional autonomous squads, which have never been discussed in terms of Spotify model before. We also present Spotify Tailoring by highlighting modified and newly introduced practices by the organisation in which the case study was conducted

Micropulsations in the electric field near the plasmapause, observed by ISEE-1

The occurrence of micropulsations near and inside the plasmapause was surveyed. The observed pulsations, classified as Pc3 and Pi2, are discussed. In addition one single event of Pc1 was observed. The frequencies in the Pc3 and Pi2 bands, the amplitude ranges, and the direction of rotation for the electric field vector are reported

Responsiveness of the International Classification of Functioning, Disability and Health (ICF) Core Set for rheumatoid arthritis

Background: The comprehensive International Classification of Functioning, Disability and Health (ICF) Core Set for rheumatoid arthritis (RA) is a selection of 96 categories from the ICF, representing relevant aspects in the functioning of patients with RA. Objectives: To study the responsiveness of the ICF Core Set for RA in rheumatological practice. Methods: A total of 46 patients with RA (72% women, mean (SD) age 53.6 (12.6) years, disease duration 6.3 (8.0) years) were interviewed at baseline and again after 6 months treatment with a disease-modifying antirheumatic drug (DMARD), applying the ICF Core Set for RA with qualifiers for problems on a modified three-point scale (no problem, mild/moderate, severe/complete). Patient-reported outcomes included Modified Health Assessment Questionnaire (MHAQ) and Short-Form 36 (SF-36) health survey, and disease activity was calculated. Responsiveness was measured as change in qualifiers in ICF categories, and was also compared with change in patient-reported outcomes. Results: After 6 months of DMARD treatment, improvement by at least one qualifier was seen in 20% of patients (averaged across all ICF categories), 71% experienced no change and 9% experienced worsening symptoms. Findings were similar across the different aspects of functioning. Mainly moderate effect sizes were seen for 6-month changes in the ICF Core Set for RA, especially in patients with improved health status, with similar effect size for disease activity. The components in the ICF Core Set for RA were only weakly associated with patient-reported outcomes and disease activity. Conclusions: The ICF Core Set for RA demonstrated moderate responsiveness in this real-life setting of patients where minor changes occurred during treatment with DMARDs

Measuring Column Densities in Quasar Outflows: VLT Observations of QSO 2359-1241

We present high resolution spectroscopic VLT observations of the outflow seen in QSO 2359-1241. These data contain absorption troughs from five resonance Fe II lines with a resolution of ~7 km/s and signal-to-noise ratio per resolution element of order 100. We use this unprecedented high quality data set to investigate the physical distribution of the material in front of the source, and by that determine the column densities of the absorbed troughs. We find that the apparent optical depth model gives a very poor fit to the data and greatly underestimates the column density measurements. Power-law distributions and partial covering models give much better fits with some advantage to power-law models, while both models yield similar column density estimates. The better fit of the power-law model solves a long standing problem plaguing the partial covering model when applied to large distance scale outflow: How to obtain a velocity dependent covering factor for an outflow situated at distances thousands of time greater than the size of the AGN emission source. This problem does not affect power-law models. Therefore, based on the better fit and plausibility of the physical model, we conclude that in QSO 2359-1241, the outflow covers the full extent of the emission source but in a non-homogeneous way.Comment: 27 pages, 6 figures, to appear on ApJ Jul 10. The full (online) version of figure 2 can be obtained here: http://www.phys.vt.edu/~arav/f2_online_version.p

EUV Sunspot Plumes Observed with SOHO

Bright EUV sunspot plumes have been observed in five out of nine sunspot regions with the Coronal Diagnostic Spectrometer -- CDS on SOHO. In the other four regions the brightest line emissions may appear inside the sunspot but are mainly concentrated in small regions outside the sunspot areas. These results are in contrast to those obtained during the Solar Maximum Mission, but are compatible with the Skylab mission results. The present observations show that sunspot plumes are formed in the upper part of the transition region, occur both in magnetic unipolar-- and bipolar regions, and may extend from the umbra into the penumbra.Comment: 8 pages, 3 figures, to be published in ApJ Letter

Cost-effective processing of a piezoresistive MEMS cantilever sensor

In this paper cost-effective methods for fabrication of a piezoresistive cantilever sensor for industrial use are focused. The intended use of the presented cantilever is a medical application. A closer description of the cantilever design is given. The low-cost processing sequence is presented and each processing step is explained in detail. Results from electrical probing and mechanical strength test are given. The results demonstrate that the chosen low-cost processing route results in high yield and a mechanical robust device

Dynamical mechanism of atrial fibrillation: a topological approach

While spiral wave breakup has been implicated in the emergence of atrial fibrillation, its role in maintaining this complex type of cardiac arrhythmia is less clear. We used the Karma model of cardiac excitation to investigate the dynamical mechanisms that sustain atrial fibrillation once it has been established. The results of our numerical study show that spatiotemporally chaotic dynamics in this regime can be described as a dynamical equilibrium between topologically distinct types of transitions that increase or decrease the number of wavelets, in general agreement with the multiple wavelets hypothesis. Surprisingly, we found that the process of continuous excitation waves breaking up into discontinuous pieces plays no role whatsoever in maintaining spatiotemporal complexity. Instead this complexity is maintained as a dynamical balance between wave coalescence -- a unique, previously unidentified, topological process that increases the number of wavelets -- and wave collapse -- a different topological process that decreases their number.Comment: 15 pages, 14 figure

Distance to Multiple Kinematic Components of Quasar Outflows: VLT Observations of QSO 2359-1241 and SDSS J0318-0600

Using high resolution VLT spectra, we study the multi-component outflow systems of two quasars exhibiting intrinsic Fe II absorption (QSO 2359-1241 and SDSS J0318-0600). From the extracted ionic column densities and using photoionization modeling we determine the gas density, total column density, and ionization parameter for several of the components. For each object the largest column density component is also the densest, and all other components have densities of roughly 1/4 of that of the main component. We demonstrate that all the absorbers lie roughly at the same distance from the source. Further, we calculate the total kinetic luminosities and mass outflow rates of all components and show that these quantities are dominated by the main absorption component.Comment: 27 pages, 5 figure