Measuring transient reaction rates from nonstationary catalysts

Up to now, methods for measuring rates of reactions on catalysts required long measurement times involving signal averaging over many experiments. This imposed a requirement that the catalyst return to its original state at the end of each experiment—a complete reversibility requirement. For real catalysts, fulfilling the reversibility requirement is often impossible—catalysts under reaction conditions may change their chemical composition and structure as they become activated or while they are being poisoned through use. It is therefore desirable to develop high-speed methods where transient rates can be quickly measured while catalysts are changing. In this work, we present velocity-resolved kinetics using high-repetition-rate pulsed laser ionization and high-speed ion imaging detection. The reaction is initiated by a single molecular beam pulse incident at the surface, and the product formation rate is observed by a sequence of pulses produced by a high-repetition-rate laser. Ion imaging provides the desorbing product flux (reaction rate) as a function of reaction time for each laser pulse. We demonstrate the principle of this approach by rate measurements on two simple reactions: CO desorption from and CO oxidation on the 332 facet of Pd. This approach overcomes the time-consuming scanning of the delay between CO and laser pulses needed in past experiments and delivers a data acquisition rate that is 10–1000 times higher. We are able to record kinetic traces of CO2 formation while a CO beam titrates oxygen atoms from an O-saturated surface. This approach also allows measurements of reaction rates under diffusion-controlled conditions

NO binding energies to and diffusion barrier on Pd obtained with velocity-resolved kinetics

We report nitric oxide (NO) desorption rates from Pd(111) and Pd(332) surfaces measured with velocity-resolved kinetics. The desorption rates at the surface temperatures from 620 to 800 K span more than 3 orders of magnitude, and competing processes, like dissociation, are absent. Applying transition state theory (TST) to model experimental data leads to the NO binding energy E0 = 1.766 ± 0.024 eV and diffusion barrier DT = 0.29 ± 0.11 eV on the (111) terrace and the stabilization energy for (110)-steps ΔEST = 0.060–0.030+0.015 eV. These parameters provide valuable benchmarks for theory

Low-Dimensional Polyoxometalate Molecules/Tantalum Oxide Hybrids for Non-Volatile Capacitive Memories

Transition-metal-oxide hybrids composed of high surface-to-volume ratio Ta2O5 matrices and a molecular analogue of transition metal oxides, tungsten polyoxometalates ([PW12O40]3-), are introduced herein as a charge storage medium in molecular nonvolatile capacitive memory cells. The polyoxometalate molecules are electrostatically self-assembled on a low-dimensional Ta2O5 matrix, functionalized with an aminosilane molecule with primary amines as the anchoring moiety. The charge trapping sites are located onto the metal framework of the electron-accepting molecular entities as well as on the molecule/oxide interfaces which can immobilize negatively charged mobile oxygen vacancies. The memory characteristics of this novel nanocomposite were tested using no blocking oxide for extraction of structure-specific characteristics. The film was formed on top of the 3.1 nm-thick SiO2/n-Si(001) substrates and has been found to serve as both SiO2/Si interface states' reducer (i.e., quality enhancer) and electron storage medium. The device with the polyoxometalates sandwiched between two Ta2O5 films results in enhanced internal scattering of carriers. Thanks to this, it exhibits a significantly larger memory window than the one containing the plain hybrid and comparable retention time, resulting in a memory window of 4.0 V for the write state and a retention time around 104 s without blocking medium. Differential distance of molecular trapping centers from the cell's gate and electronic coupling to the space charge region of the underlying Si substrate were identified as critical parameters for enhanced electron trapping for the first time in such devices. Implementing a numerical electrostatic model incorporating structural and electronic characteristics of the molecular nodes derived from scanning probe and spectroscopic characterization, we are able to interpret the hybrid's electrical response and gain some insight into the electrostatics of the trapping medium. © 2016 American Chemical Society

The barrier for CO2 functionalization to formate on hydrogenated Pt

Understanding heterogeneous catalysis is based on knowing the energetic stability of adsorbed reactants, intermediates, and products as well as the energetic barriers separating them. We report an experimental determination of the barrier to CO2 functionalization to form bidentate formate on a hydrogenated Pt surface and the corresponding reaction energy. This determination was possible using velocity resolved kinetics, which simultaneously provides information about both the dynamics and rates of surface chemical reactions. In these experiments, a pulse of isotopically labeled formic acid (DCOOH) doses the Pt surface rapidly forming bidentate formate (DCO*O*). We then record the (much slower) rate of decomposition of DCO*O* to form adsorbed D* and gas phase CO2. We establish the reaction mechanism by dosing with O2 to form adsorbed O*, which efficiently converts H* or D* to gas phase water. H2O is formed immediately reflecting rapid loss of the acidic proton associated with formation of formate, while D2O formation proceeds more slowly and on the same time scale as the CO2 production. The temperature dependence of the reaction rate yields an activation energy that reflects the energy of the transition state with respect to DCO*O*. The derived heat of formation for DCO*O* on Pt(111) agrees well with results of microcalorimetry. The maximum release of translational energy of the formed CO2 provides a measure of the energy of the transition state with respect to the products and the barrier to the reverse process, functionalization of CO2. The comparison between the results on Pt(111) and Pt(332) shows that the barrier for CO2 functionalization is reduced by the presence of steps. The approach taken here could provide a method to optimize catalysts for CO2 functionalization

Quantum effects in thermal reaction rates at metal surfaces

Accurate description of elementary steps of chemical reactions at surfaces is a long-standing challenge because of the lack of reliable experimental measurements of the corresponding rate constants, which also makes it impossible to rigorously validate theoretical estimates. Even for reactions as simple as thermal recombination of hydrogen atoms on platinum surfaces, previous experimental rate constants have only been obtained with large uncertainties. Using velocity-resolved kinetics and ion imaging–based calibration of absolute molecular beam fluxes, Borodin et al. managed to overcome established experimental difficulties and report unprecedentedly accurate rate constants for this reaction over a wide temperature range. They also demonstrate a parameter-free model that quantitatively reproduces the experiment, opening up new vistas for the growing field of computational heterogeneous catalysi

Atomic-layer-deposited aluminum and zirconium oxides for surface passivation of TiO 2 in High-Efficiency Organic Photovoltaics

The reduction in electronic recombination losses by the passivation of surfaces is a key factor enabling high-efficiency solar cells. Here we investigate a strategy to passivate surface trap states of TiO 2 films used as cathode interlayers in organic photovoltaics (OPVs) through applying alumina (Al2O3) or zirconia (ZrO2) insulating nanolayers by thermal atomic layer deposition (ALD). Our results suggest that the surface traps in TiO 2 are oxygen vacancies, which cause undesirable recombination and high electron extraction barrier, reducing the open-circuit voltage and the short-circuit current of the complete OPV device. It was found that the ALD metal oxides enable excellent passivation of the TiO2 surface followed by a downward shift of the conduction band minimum. OPV devices based on different photoactive layers and using the passivated TiO2 electron extraction layers exhibited a significant enhancement of more than 30% in their power conversion efficiencies (PCEs) as compared to their reference devices without the insulating metal oxide nanolayers as a result of significant suppression of charge recombination and enhanced electron extraction rates at the TiO2/ALD metal-oxide/organic interface.European Social Fund (ESF) and Greek national funds via the Research Funding Program ARCHIMEDES III