5,662 research outputs found
Material flow during the extrusion of simple and complex cross-sections using FEM
This paper deals with the extrusion of rod and shape sections and uses a 3D finite element model analysis (FEM) to predict the effect of die geometry on maximum extrusion load. A description of material flow in the container is considered in more detail for rod and shape sections in order to fully comprehend the transient conditions occurring during the process cycle. A comparison with experiments is made to assess the relative importance of some extrusion parameters in the extrusion process and to ensure that the numerical discretisation yields a realistic simulation of the process. The usefulness and the limitation of FEM are discussed when modelling complex shapes. Results are presented for velocity contours and shear stress distribution during the extrusion process. It is shown that for most of the shapes investigated, the material making up
the extrudate cross-sections originates from differing regions of virgin material within the billet. The outside surface of the extrudate originates from the material moving along the dead metal zone (DMZ) and the core of the extrudate from the central deformation zone. The FE program
appears to predict all the major characteristics of the flow observed macroscopically
Material flow during the extrusion of simple and complex cross-sections using FEM
This paper deals with the extrusion of rod and shape sections and uses a 3D finite element model analysis (FEM) to predict the effect of die geometry on maximum extrusion load. A description of material flow in the container is considered in more detail for rod and shape sections in order to fully comprehend the transient conditions occurring during the process cycle. A comparison with experiments is made to assess the relative importance of some extrusion parameters in the extrusion process and to ensure that the numerical discretisation yields a realistic simulation of the process. The usefulness and the limitation of FEM are discussed when modelling complex shapes. Results are presented for velocity contours and shear stress distribution during the extrusion process. It is shown that for most of the shapes investigated, the material making up
the extrudate cross-sections originates from differing regions of virgin material within the billet. The outside surface of the extrudate originates from the material moving along the dead metal zone (DMZ) and the core of the extrudate from the central deformation zone. The FE program
appears to predict all the major characteristics of the flow observed macroscopically
Thermal simulation of magnetization reversals for size-distributed assemblies of core-shell exchange biased nanoparticles
A temperature dependent coherent magnetization reversal model is proposed for
size-distributed assemblies of ferromagnetic nanoparticles and
ferromagnetic-antiferromagnetic core-shell nanoparticles. The nanoparticles are
assumed to be of uniaxial anisotropy and all aligned along their easy axis. The
thermal dependence is included by considering thermal fluctuations, implemented
via the N\'eel-Arrhenius theory. Thermal and angular dependence of
magnetization reversal loops, coercive field and exchange-bias field are
obtained, showing that F-AF size-distributed exchange-coupled nanoparticles
exhibit temperature-dependent asymmetric magnetization reversal. Also,
non-monotonic evolutions of He and Hc with T are demonstrated. The angular
dependence of Hc with T exhibits a complex behavior, with the presence of an
apex, whose position and amplitude are strongly T dependent. The angular
dependence of He with T exhibits complex behaviors, which depends on the AF
anisotropy and exchange coupling. The resulting angular behavior demonstrates
the key role of the size distribution and temperature in the magnetic response
of nanoparticles.Comment: Revised arguments in Introduction and last sectio
Variation of turbulent burning rate of methane, methanol, and iso-octane air mixtures with equivalence ratio at elevated pressure
Turbulent burning velocities for premixed methane, methanol, and iso-octane/air mixtures have been experimentally determined for an rms turbulent velocity of 2 m/s and pressure of 0.5 MPa for a wide range of equivalence ratios. Turbulent burning velocity data were derived using high-speed schlieren photography and transient pressure recording; measurements were processed to yield a turbulent mass rate burning velocity, utr. The consistency between the values derived using the two techniques, for all fuels for both fuel-lean and fuel-rich mixtures, was good. Laminar burning measurements were made at the same pressure, temperature, and equivalence ratios as the turbulent cases and laminar burning velocities and Markstein numbers were determined. The equivalence ratio (Ăâ ) for peak turbulent burning velocity proved not always coincident with that for laminar burning velocity for the same fuel; for isooctane, the turbulent burning velocity unexpectedly remained high over the range Ăâ = 1 to 2. The ratio of turbulent to laminar burning velocity proved remarkably high for very rich iso-octane/air and lean methane/air mixtures
Lorentz Beams
A new kind of tridimensional scalar optical beams is introduced. These beams
are called Lorentz beams because the form of their transverse pattern in the
source plane is the product of two independent Lorentz functions. Closed-form
expression of free-space propagation under paraxial limit is derived and pseudo
non-diffracting features pointed out. Moreover, as the slowly varying part of
these fields fulfils the scalar paraxial wave equation, it follows that there
exist also Lorentz-Gauss beams, i.e. beams obtained by multipying the original
Lorentz beam to a Gaussian apodization function. Although the existence of
Lorentz-Gauss beams can be shown by using two different and independent ways
obtained recently from Kiselev [Opt. Spectr. 96, 4 (2004)] and Gutierrez-Vega
et al. [JOSA A 22, 289-298, (2005)], here we have followed a third different
approach, which makes use of Lie's group theory, and which possesses the merit
to put into evidence the symmetries present in paraxial Optics.Comment: 11 pages, 1 figure, submitted to Journal of Optics
Detecting the harmonics of oscillations with time-variable frequencies
A method is introduced for the spectral analysis of complex noisy signals containing several frequency components. It enables components that are independent to be distinguished from the harmonics of nonsinusoidal oscillatory processes of lower frequency. The method is based on mutual information and surrogate testing combined with the wavelet transform, and it is applicable to relatively short time series containing frequencies that are time variable. Where the fundamental frequency and harmonics of a process can be identified, the characteristic shape of the corresponding oscillation can be determined, enabling adaptive filtering to remove other components and nonoscillatory noise from the signal. Thus the total bandwidth of the signal can be correctly partitioned and the power associated with each component then can be quantified more accurately. The method is first demonstrated on numerical examples. It is then used to identify the higher harmonics of oscillations in human skin blood flow, both spontaneous and associated with periodic iontophoresis of a vasodilatory agent. The method should be equally relevant to all situations where signals of comparable complexity are encountered, including applications in astrophysics, engineering, and electrical circuits, as well as in other areas of physiology and biology
The structure of epitaxial V2O3 films and their surfaces : a medium energy ion scattering study
Medium energy ion scattering, using 100 keV H+ incident ions, has been used to investigate the growth of epitaxial films, up to thicknesses of ~200 Ă
, of V2O3 on both Pd(111) and Au(111). Scattered-ion energy spectra provide a measure of the average film thickness and the variations in this thickness, and show that, with suitable annealing, the crystalline quality is good. Plots of the scattering yield as a function of scattering angle, so-called blocking curves, have been measured for two different incidence directions and have been used to determine the surface structure. Specifically, scattering simulations for a range of different model structures show poor agreement with experiment for half-metal (âŠ.VâO3V) and vanadyl (âŠ.VâO3V=O) terminations, with and without surface interlayer relaxations. However, good agreement with experiment is found for the modified oxygen-termination structure, first proposed by Kresse et al., in which a subsurface V half-metal layer is moved up into the outermost V buckled metal layer to produce a VO2 overlayer on the underlying V2O3, with an associated layer structure of âŠ.O3VVââVâO3
- âŠ