Effect of beating process to soda anthraquinone pulp of oil palm male flower spikes fibre

This study was carried out to investigate the effect of beating process to the characteristics of pulp and paper produced from oil palm oil male flower spikes (OPMFS). OPMFS pulp was prepared according to chemical Soda-AQ pulping process. 60 gsm handsheet of oil palm male flower spikes paper were prepared from OPMFS pulp with four different beating times which are O revolution, 1000 revolutions, 2000 revolutions and 3000 revolutions. All physical and mechanical characteristics were investigated according to T APPi and MS ISO standards. The results show that overall physical and mechanical characteristics of POMPS paper were influenced and enhanced by beating process between O until 3000 revolutions. This research demonstrate some potential characteristics of palm oil male flower spikes (OPMFS) paper to be investigated as a newly explored non-wood based raw material for papermaking raw material for papermaking

Soda anthraquinone pulping of oil palm male flower spikes

This study was carried out to investigate the effect of beating process to the characteristics of pulp and paper produced from oil palm oil male flower spikes (OPMFS). OPMFS pulp was prepared according to chemical Soda-AQ pulping process. 60 gsm papersheet of oil palm male flower spiked were prepared from unbeaten and unbleached OPMFS Soda-AQ pulp. All optical, physical and mechanical characteristics were investigated according to TAPPI and MS ISO standards. OPMFS pulp recorded value of 6.42 s, 353 ml, 76.5 %, 36.7 % and 9.35 for drainage time, freeness, moisture content, screened yield percentage and Kappa number respectively..

Molybdenum back-contact optimization for CIGS thin film solar cell

Molybdenum (Mo) thin films are most widely used as an ohmic back-contact in the copper indium diselenide (CIS) and its alloy copper indium gallium diselenide (CIGS) based thin film solar cell. Radio frequency (RF) magnetron sputtering system used to deposit Mo thin films on soda lime glass substrate. The deposition was carried out using argon (Ar) gas at different Ar controlled (working) pressures (1 mTorr to 10 mTorr) and at different RF powers (60 W to 100 W). The influence of both the working pressure and the RF power on the Mo thin films was studied by investigating its structural, morphological, electrical, and optical measurements. The results reveal that a stress-free, low-sheet-resistance (~1 W/), and reflecting (~ 55 %) Mo thin film was observed at 1 mTorr working pressure and 100 W RF power. When you are citing the document, use the following link http://essuir.sumdu.edu.ua/handle/123456789/2211

Smart nanocrystals of artemether: fabrication, characterization, and comparative in vitro and in vivo antimalarial evaluation

YesArtemether (ARTM) is a very effective antimalarial drug with poor solubility and consequently low bioavailability. Smart nanocrystals of ARTM with particle size of 161±1.5 nm and polydispersity index of 0.172±0.01 were produced in <1 hour using a wet milling technology, Dena® DM-100. The crystallinity of the processed ARTM was confirmed using differential scanning calorimetry and powder X-ray diffraction. The saturation solubility of the ARTM nanocrystals was substantially increased to 900 µg/mL compared to the raw ARTM in water (145.0±2.3 µg/mL) and stabilizer solution (300.0±2.0 µg/mL). The physical stability studies conducted for 90 days demonstrated that nanocrystals stored at 2°C-8°C and 25°C were very stable compared to the samples stored at 40°C. The nanocrystals were also shown to be stable when processed at acidic pH (2.0). The solubility and dissolution rate of ARTM nanocrystals were significantly increased (P<0.05) compared to those of its bulk powder form. The results of in vitro studies showed significant antimalarial effect (P<0.05) against Plasmodium falciparum and Plasmodium vivax. The IC50 (median lethal oral dose) value of ARTM nanocrystals was 28- and 54-fold lower than the IC50 value of unprocessed drug and 13- and 21-fold lower than the IC50 value of the marketed tablets, respectively. In addition, ARTM nanocrystals at the same dose (2 mg/kg) showed significantly (P<0.05) higher reduction in percent parasitemia (89%) against P. vivax compared to the unprocessed (27%), marketed tablets (45%), and microsuspension (60%). The acute toxicity study demonstrated that the LD50 value of ARTM nanocrystals is between 1,500 mg/kg and 2,000 mg/kg when given orally. This study demonstrated that the wet milling technology (Dena® DM-100) can produce smart nanocrystals of ARTM with enhanced antimalarial activities

Barriers to development and progression of women entrepreneurs in Pakistan

This article would help integration of women entrepreneurs into the mainstream economy in Pakistan.In Pakistan, women entrepreneurs do not enjoy the same opportunities as men due to a number of deep-rooted discriminatory socio-cultural values and traditions. Furthermore, these restrictions can be observed within the support mechanisms that exist to assist such fledgling businesswomen. The economic potential of female entrepreneurs is not being realised as they suffer from a lack of access to capital, land, business premises, information technology, training and agency assistance. Inherent attitudes of a patriarchal society, that men are superior to women and that women are best suited to be homemakers, create formidable challenges. Women also receive little encouragement from some male family members, resulting in limited spatial mobility and a dearth of social capital. The research suggests that in order to foster development, multi-agency cooperation is required. The media, educational policy makers and government agencies could combine to provide women with improved access to business development services and facilitate local, regional and national networks

Reconfigurable multi-legs robot for pipe inspection: Design and gait movement

1132-1144This paper focuses on studies on reconfigurable multi-legs robotic system. The aim of this paper is to identify and acquire findings on how multi-legs robot can walk, climb vertical pipe and walk along the horizontal pipe after climbing. Three degrees of freedom (3DOF) multi-legs robot is designed and built to replace human involvement either at hazardous pipeline or to check on vertical and horizontal pipes. The robot system is tested to climb the vertical pipe and then move along horizontal pipe for inspection or other purposes. This can reduce the cost and percentage of human risk exposure during inspection on outer pipe. This multi-legs robot has more movement gaits compared to wheeled robot, but in terms of speed, wheeled robot possesses greater advantages. Therefore, this system design has combination of both wheel and multiple legs ensure that the to system has higher stability, more gait movement, and higher speed manoeuvrability. The gaits analysis for the system movement includes angle of the legs to move and selection of certain legs to perform a given operation, either walking, climbing or hanging. The target result is the system able to climb 500 mm height with 85 mm radius pipe. The potential applications for the system are: (i) to move along either on surface or underwater pipe and (ii) to be equipped with ultrasonic sensor to inspect the pipe.</em

Comprehensive review on controller for leader-follower robotic system

985-1007This paper presents a comprehensive review of the leader-follower robotics system. The aim of this paper is to find and elaborate on the current trends in the swarm robotic system, leader-follower, and multi-agent system. Another part of this review will focus on finding the trend of controller utilized by previous researchers in the leader-follower system. The controller that is commonly applied by the researchers is mostly adaptive and non-linear controllers. The paper also explores the subject of study or system used during the research which normally employs multi-robot, multi-agent, space flying, reconfigurable system, multi-legs system or unmanned system. Another aspect of this paper concentrates on the topology employed by the researchers when they conducted simulation or experimental studies

Deposition and Characterization of Indium Selenide Thin Films for Opto-electronic Devices

Amongst all the III-VI semiconductors, ones that crystallize with a layered structure have gained special interest due to its significant usage in photovoltaic devices. III-VI layered semiconductor such as InSe has low density of dangling bonds on its surface therefore it is considered as vital material for the fabrication of opto-electronic devices like photo sensor, solar cell etc. In present work, InSe thin films were fabricated through a simple and facile drop-casting method, where the thin films were drop-casted between two silver paste electrodes on a glass substrate. The structural, surface morphological, compositional, electrical and optical properties of the prepared films were obsrved by XRD, SEM, EDAX, high precision digital multi-meter and UV-visible spectroscopy, respectively. XRD analysis of the prepared film shows the existence of nano-crystalline nature with monoclinic crystal structure of InSe. SEM images show good continuity of InSe film. InSe thin films are n-type with bandgap of 1.8 eV and their electrical conductivity is in the order of 10 – 10 S/cm that makes them appropriate for using as an absorber layer in the solar cell

Development of a monoclonal antibody-based co-agglutination test to detect enterotoxigenic Escherichia coli isolated from diarrheic neonatal calves

Escherichia coli (E. coli) strains were collected from young diarrheic calves in farms and field. Strains that expressed the K99 (F5) antigen were identified by agglutination tests using reference antibodies to K99 antigen and electron microscopy. The K99 antigen from a selected field strain (SAR-14) was heat-extracted and fractionated on a Sepharose CL-4B column. Further purification was carried out by sodium deoxycholate treatment and/or ion-exchange chromatography. Monoclonal antibodies to purified K99 antigen were produced by the hybridoma technique, and a specific clone, NEK99-5.6.12, was selected for propagation in tissue culture. The antibodies, thus obtained, were affinity-purified, characterized and coated onto Giemsa-stained Cowan-I strain of Staphylococcus aureus (S. aureus). The antibody-coated S. aureus were used in a co-agglutination test to detect K99+ E. coli isolated from feces of diarrheic calves. The specificity of the test was validated against reference monoclonal antibodies used in co-agglutination tests, as well as in ELISA. Specificity of the monoclonal antibodies was also tested against various Gram negative bacteria. The developed antibodies specifically detected purified K99 antigen in immunoblots, as well as K99+ E. coli in ELISA and co-agglutination tests. The co-agglutination test was specific and convenient for large-scale screening of K99+ E. coli isolates