Design study of a thermocouple power sensor as a monolithic fin-line

Making traceable power measurements above 110 GHz using current measurement technologies is challenging. We investigate a design of power sensor consisting of a thermocouple-based integrated circuit (IC) mounted as a finline component in WR-6 waveguide. The design is original in that it contains an antenna, terminating resistor and thermocouples on-chip. We detail the design and report results from simulations and measurements made on a two-port 16:1 scale model. Our design of scale model provides both insertion and reflection loss measurements. Electromagnetic simulation and easily-calibrated model measurements confirm that the short antenna fins feasible on a monolithic microwave integrated circuit (MMIC) can achieve acceptable specifications. The design proves to be relatively insensitive to the value of the terminating resistance or the size of the antenna fins

The energy efficiency of 8-bit low-power microcontrollers

We have measured the energy cost of processing, sleeping, non-volatile memory writes and ADC measurements of six 8-bit microprocessors from three manufacturers. These measurements compare the chips directly to one another and reveal ideal operating points which can be used to reduce energy consumption

Scaling of Electrode-Electrolyte Interface Model Parameters In Phosphate Buffered Saline

We report how the impedance presented by a platinum electrode scales with the concentration of phosphate buffered saline (PBS). We find that the constant phase element of the model scales with approximately the log of concentration, whereas the resistivity is inversely proportional. Using a novel DC measurement technique we show that the Faradaic response of a platinum electrode, and thus the safe exposure limit, does not scale with concentration below 900mV overpotential across a pair of electrodes. We compare objective measurements made in saline to those made in the spinal cavity of live sheep. We comment upon the appropriateness of using PBS as a substitute for living sheep

Feasibility of Harvesting Power To Run A Domestic Water Meter Using Streaming Cell Technology

We investigate the possibility of using streaming cells as a means of harvesting energy from the town water supply. We measure the electrical power developed from streaming cells using tap water as a working fluid. We estimate the amount of energy available from a typical domestic household based on water usage data. We estimate the amount of energy required to operate a simple data logger and transmitter. From these estimates we calculate the required efficiency and physical form of a streaming cell energy converter. We comment on the feasibility of using streaming cell technology as a means of harvesting energy from a domestic water supply

The build, operate, and transfer ("BOT") approach to infrastructure projects in developing countries

Build, operate and transfer (BOT) projects are exceedingly complex from both a financial and a legal point of view. They require an extended period of time to develop and negotiate. If a country is not able to finance all of its needed infrastructure on the basis of budgetary resources or sovereign borrowings, the BOT approach is an option to be considered. A BOT project appears to provide some"additionality"in tapping sources of private sector financing which otherwise might not be available. The sponsors'commitment of substantial equity to a project assures that they will also remain committed to the project's successful operation over the concession period. Their investment provides a strong incentive to have the project perform above its minimum expectations. Likewise, having the design, implementation and operation of a BOT project largely in the hands of the private sector may provide economies and efficiencies that will balance out or even outweight the higher financing costs of non sovereign borrowing and equity investment. The BOT approach appears to be a useful possible alternative to the conventional financing and operation of infrastructure projects in developing countries.Municipal Financial Management,Public Sector Economics&Finance,Housing Finance,Environmental Economics&Policies,Banks&Banking Reform

Conditions for rapid mixing of parallel and simulated tempering on multimodal distributions

We give conditions under which a Markov chain constructed via parallel or simulated tempering is guaranteed to be rapidly mixing, which are applicable to a wide range of multimodal distributions arising in Bayesian statistical inference and statistical mechanics. We provide lower bounds on the spectral gaps of parallel and simulated tempering. These bounds imply a single set of sufficient conditions for rapid mixing of both techniques. A direct consequence of our results is rapid mixing of parallel and simulated tempering for several normal mixture models, and for the mean-field Ising model.Comment: Published in at http://dx.doi.org/10.1214/08-AAP555 the Annals of Applied Probability (http://www.imstat.org/aap/) by the Institute of Mathematical Statistics (http://www.imstat.org

Choosing the right microcontroller: A comparison of 8-bit Atmel, Microchip and Freescale MCUs

When choosing a microcontroller there are many options, so which platform should you choose? There is little independent information available to help engineers decide which platform might best suit their needs and most designers tend to stick with the brand with which they are familiar. This is a difficult question to answer without bias if the people conducting the evaluations have had previous experience with MCU programming predominantly on one platform. This article draws on a case study. We built three “Smart” Sprinkler Taps, small, self-contained irrigation controllers, differing only in the microcontroller unit (MCU) on the inside. We compare cost, development software quality and hardware performance from the perspective of a new user to each of the platforms

Identifying and Correcting Step Losses in Single-Ended Fiber-Optic Distributed Temperature Sensing Data

Fiber-optic distributed temperature sensing (DTS) makes it possible to observe temperatures on spatial scales as fine as centimeters and at frequencies up to 1 Hz. Over the past decade, fiber-optic DTS instruments have increasingly been employed to monitor environmental temperatures, from oceans to atmospheric monitoring. Because of the nature of environmental deployments, optical fibers deployed for research purposes often encounter step losses in the Raman spectra signal. Whether these phenomena occur due to cable damage or impingements, sharp bends in the deployed cable, or connections and splices, the step losses are usually not adequately addressed by the calibration routines provided by instrument manufacturers and can be overlooked in postprocessing calibration routines as well. Here we provide a method to identify and correct for the effects of step losses in raw Raman spectra data. The utility of the correction is demonstrated with case studies, including synthetic and laboratory data sets

Mixed-method study of a conceptual model of evidence-based intervention sustainment across multiple public-sector service settings.

BackgroundThis study examines sustainment of an EBI implemented in 11 United States service systems across two states, and delivered in 87 counties. The aims are to 1) determine the impact of state and county policies and contracting on EBI provision and sustainment; 2) investigate the role of public, private, and academic relationships and collaboration in long-term EBI sustainment; 3) assess organizational and provider factors that affect EBI reach/penetration, fidelity, and organizational sustainment climate; and 4) integrate findings through a collaborative process involving the investigative team, consultants, and system and community-based organization (CBO) stakeholders in order to further develop and refine a conceptual model of sustainment to guide future research and provide a resource for service systems to prepare for sustainment as the ultimate goal of the implementation process.MethodsA mixed-method prospective and retrospective design will be used. Semi-structured individual and group interviews will be used to collect information regarding influences on EBI sustainment including policies, attitudes, and practices; organizational factors and external policies affecting model implementation; involvement of or collaboration with other stakeholders; and outer- and inner-contextual supports that facilitate ongoing EBI sustainment. Document review (e.g., legislation, executive orders, regulations, monitoring data, annual reports, agendas and meeting minutes) will be used to examine the roles of state, county, and local policies in EBI sustainment. Quantitative measures will be collected via administrative data and web surveys to assess EBI reach/penetration, staff turnover, EBI model fidelity, organizational culture and climate, work attitudes, implementation leadership, sustainment climate, attitudes toward EBIs, program sustainment, and level of institutionalization. Hierarchical linear modeling will be used for quantitative analyses. Qualitative analyses will be tailored to each of the qualitative methods (e.g., document review, interviews). Qualitative and quantitative approaches will be integrated through an inclusive process that values stakeholder perspectives.DiscussionThe study of sustainment is critical to capitalizing on and benefiting from the time and fiscal investments in EBI implementation. Sustainment is also critical to realizing broad public health impact of EBI implementation. The present study takes a comprehensive mixed-method approach to understanding sustainment and refining a conceptual model of sustainment