Investigation of the spectral lag - energy relation of GRBs registered by INTEGRAL

We investigated the dependence of spectral lag on energy band based on 28 bright GRBs detected by the SPI and IBIS/ISGRI instruments on the INTEGRAL observatory. It is found that for simple structured bursts or well separated pulses of multi-pulse bursts the spectral lag can be approximated by the relation t=Alog(E), where A is a positive parameter, which correlates with pulse duration. We have not found any negative lag in simple structured bursts or in well separated pulses. While investigating the time profile of the whole burst negative lag may appear due to different spectral parameters of the pulses.Comment: 6 pages, 2 figures, Proceedings of "An INTEGRAL view of the high-energy sky (the first 10 years)" the 9th INTEGRAL Workshop, October 15-19, 2012, Paris, France, in Proceedings of Science (INTEGRAL 2012), Eds. A. Goldwurm, F. Lebrun and C. Winkler, (http://pos.sissa.it/cgi-bin/reader/conf.cgi?confid=176), id 12

Calibrating SPI-ACS/INTEGRAL for gamma-ray bursts and re-estimating energetics of GRB/GW 190425 in gamma-ray range

SPI-ACS/INTEGRAL is one of the most sensitive orbital gamma-ray detectors in energy range above 80 keV. Since 2002 it registered several thousands of gamma-ray bursts, including the bursts associated with LIGO-Virgo gravitational wave events GW 170817 and GW 190425. No dedicated in-flight calibrations were performed for SPI-ACS/INTEGRAL, complicating estimation of spectral and energetic characteristics of an event. Using data of GBM/Fermi we perform cross-calibration of SPI-ACS/INTEGRAL, based on 1032 bright GRBs registered by both experiments. We find the conversion factor between instrumental counts from SPI-ACS and energy units from GBM to be dependent on hardness of GRB spectrum (defined as the characteristic energy value, $E_{p}$) and on location of a source in spacecraft based coordinate system. We determine the corresponding analytical model to calculate the conversion factor and estimate its accuracy empirically. Sensitivity of SPI-ACS/INTEGRAL to detect gamma-ray transients is also investigated. Using the calibration we re-estimate energetics of GRB/GW 190425, detected by SPI-ACS/INTEGRAL alone. We constrain possible range of the characteristic energy $E_{p}$ and isotropic equivalent of total energy, emitted in gamma-rays $E_{iso}$ for GRB 190425, using the $E_{p,i}$ -- $E_{iso}$ (Amati) correlation. The calibration model could be applied to any transients with energy spectrum, analogous to gamma-ray bursts.Comment: 11 pages, 11 figures, Accepted to MNRAS 2023 August 3, in original form 2023 June 2

Extended Emission of Cosmic Gamma-Ray Bursts Detected in the SPI-ACS/INTEGRAL Experiment

We have carried out a systematic analysis of the gamma-ray bursts' (GRBs) light curves detected in the SPI-ACS experiment onboard the INTEGRAL observatory aimed to search extended emission. The emission occasionally recorded after the prompt active phase of a GRB in the form of an emission that is longer than the active phase and less intense is called the extended one. Out of the 739 brightest GRBs recorded from 2002 to 2017, extended emission has been detected in $\sim20\%$ of the individual light curves; its maximum duration reaches $\sim 10000$ s. Two different types of extended emission have been revealed. One of them is an additional component of the light curve and is described by a power law (PL) with an index $\alpha \sim -1$ close to the PL index of the afterglow in the optical and X-ray bands. The second type can be described by a steeper PL decay of the light curve typical of the active burst phase. Extended emission has also been found in the combined light curve of long GRBs in the individual curves of which no extended emission has been detected. The PL index of the extended emission in the combined light curve is $\alpha \sim -2.4$. It is most likely associated with the superposition of light curves at the active phase; its total duration is $\sim 800$ s

Features of Polymeric Structures By Surface—Selective Laser Sintering of Polymer Particles Using Water as Sensitizer

The development of scaffolds with strictly specific properties is a key aspect of functional tissue regeneration, and it still remains one of the greatest challenges for tissue engineering. This study is aimed to determine the possibility of producing three-dimensional polylactide (PLA) scaffolds using the method of surface-selectiv  laser sintering (SSLS) for bone tissue regeneration. In this work, the authors also improved PLA scaffold adhesion properties, which are crucial for successful cellular growth and expansion. Thus, SSLS method proved to be effective in designing threedimensional porous scaffolds with differentiated mechanical properties. Keywords: regenerative medicine, scaffolds, polylactide, surface – selective laser . sintering, tissue engeneering