929 research outputs found
Novel Nanostructures And Processes For Enhanced Catalysis Of Composite Solid Propellants
The purpose of this study is to examine the burning behaviour of composite solid propellants (CSP) in the presence of nanoscale, heterogenous catalysts. The study targets the decomposition of ammonium perchlorate (AP) as a key component in the burning profile of these propellants, and seeks to identify parameters of AP decomposition reaction that can be affected by catalytic additives. The decomposition behavior of AP was studied in the presence of titanium dioxide nanoparticles in varying configurations, surface conditions, dopants, morphology, and synthesis parameters with the AP crystals. The catalytic nanoparticles were found to enhance the decomposition rate of the ammonium perchlorate, and promote an accelerated burning rate of CSP propellants containing the additives. Furthermore, different configurations were shown to have varying degrees of effectiveness in promoting the decomposition behaviour. To study the effect of the catalyst’s configuration in the bulk propellant, controlled dispersion conditions of the nanoparticle catalysts were created and studied using differential scanning calorimetry, as well as model propellant strand burning. The catalysts were shown to promote the greatest enthalpy of reaction, as well as the highest burn rate, when the AP crystals were recrystalized around the nanoparticle additives. This is in contrast to the lowest enthalpy condition, which corresponded to catalysts being dispersed upon the AP crystal surface using bio-molecule templates. Additionally, a method of facile, visible light nanoparticle tracking was developed to study the effect of mixing and settling parameters on the nano-catalysts. To accomplish this, the titania nanoparticles were doped with fluorescent europium molecules to track the dispersion of the catalysts in the propellant binder. This method was shown to succesfully allow for dispersion and agglomeration monitoring without affecting the catalytic effect of the TiO2 nanoparticles
Public Health Workforce Shortages Imperil Nation's Health
Examines from a community-based perspective the scope of the shortages in the public health workforce; contributing factors such as inadequate funding, salaries, and benefits; and strategies for training, recruiting, and retaining public health workers
Observations of directional gamma prime coarsening during engine operation
Two alloys with negative mismatch parameters, NASAIR 100 and a modified NASAIR 100 called Alloy 3 were run as turbine blades in an experimental ground based Garret TFE731 engine for up to 200 hr. The directional coarsening of gamma prime (rafting) that developed during engine testing was analyzed and compared to previous research from laboratory tests. The blades were found to be rafted normal to the centrifugal stress axis over much of the span, but near the surfaces, the blades were found to be rafted parallel to the centrifugal stress axis for certain cycles. Representative photomicrographs of the blades and the effects of stress and temperature on raft formation are shown
Investigation of the dynamic lateral stability and control characteristics of a model of a fighter airplane without a horizontal tail and equipped with either single or twin vertical tails
LCF Life of NiCr-Y Coated Disk Alloys After Shot Peening, Oxidation and Hot Corrosion
In a prior companion study (Ref. 1), three different Ni-Cr coating compositions (29, 35.5, 45 wt% Cr) were applied at two thicknesses by Plasma Enhanced Magnetron Sputtering (PEMS) to two similar Ni-based disk alloys. One coating also received a thin ZrO2 overcoat. The low cycle fatigue (LCF) life of each coating was determined at 760 C and was less than that of the uncoated specimens. In this followon effort, shot peening was examined as a means to improve the as-deposited coating morphology as well as impart a residual compressive stress in the near-surface region. After evaluating the effect of the shot peening on the LCF life, the effectiveness of the shot-peened coating in protecting the disk alloy from oxidation and hot corrosion attack was evaluated. This evaluation was accomplished by exposing coated and shot-peened specimens to 500 h of oxidation followed by 50 h of hot corrosion, both at 760 C in air. These exposed specimens were then tested in fatigue and compared to similarly treated and exposed uncoated specimens. For all cases, shot peening improved the LCF life of the coated specimens. More specifically, the highest Cr coating showed the best LCF life of the coated specimens after shot peening, as well as after the environmental exposures. Characterization of the coatings after shot peening, oxidation, hot corrosion and LCF testing is presented and discussed
Introduction
Introduction / Cathy Callaway -- Linguistics and lentil soup / Pamela A. Draper -- Eugene Lane and Ellis Library / Michael Muchow -- Gene Lane : Commitment to scholarship, teaching, and community / Robert A. Seelinger, Jr. -- Tabula Gratulatoria
Single- and double-scattering production of four muons in ultraperipheral PbPb collisions at the Large Hadron Collider
We discuss production of two pairs in ultraperipheral
ultrarelativistic heavy ion collisions at the LHC. We take into account
electromagnetic (two-photon) double-scattering production and for a first time
direct production of four muons in one scattering. We study the
unexplored process . We present
predictions for total and differential cross sections. Measurable nuclear cross
sections are obtained and corresponding differential distributions and counting
rates are presented.Comment: 13 pages, 11 figures, 1 tabl
- …