The effect of water absorption on the dielectric properties of epoxy nanocomposites

In this research, the influence of water absorption on the dielectric properties of epoxy resin and epoxy micro-composites and nano-composites filled with silica has been studied. Nanocomposites were found to absorb significantly more water than unfilled epoxy. However, the microcomposite absorbed less water than unfilled epoxy: corresponding to reduced proportion of the epoxy in this composite. The glass transition temperatures of all the samples were measured by both differential scanning calorimetry and dielectric spectroscopy. The Tg decreased as the water absorption increased and, in all cases, corresponded to a drop of approximately 20K as the humidity was increased from 0% to 100%. This implied that for all the samples, the amount of water in the resin component of the composites was almost identical. It was concluded that the extra water found in the nanocomposites was located around the surface of the nanoparticles. This was confirmed by measuring the water uptake, and the swelling and density change, as a function of humidity as water was absorbed. The water shell model, originally proposed by Lewis and developed by Tanaka, has been further developed to explain low frequency dielectric spectroscopy results in which percolation of charge carriers through overlapping water shells was shown to occur. This has been discussed in terms of a percolation model. At 100% relative humidity, water is believed to surround the nanoparticles to a depth of approximately 5 monolayers. A second layer of water is proposed that is dispersed by sufficiently concentrated to be conductive; this may extend for approximately 25 nm. If all the water had existed in a single layer surrounding a nanoparticle, this layer would have been approximately 3 to 4 nm thick at 100%. This "characteristic thickness" of water surrounding a given size of nanoparticle appeared to be independent of the concentration of nanoparticles but approximately proportional to water uptake. Filler particles that have surfaces that are functionalized to be hydrophobic considerably reduce the amount of water absorbed in nanocomposites under the same conditions of humidity. Comments are made on the possible effect on electrical aging

A "water shell" model for the dielectric properties of hydrated silica-filled epoxy nano-composites

The electrical properties of epoxy resin have been studied as a function of hydration. The epoxy was studied in an un-filled state, filled with 40 µm SiO2 particles, and filled with 50 nm SiO2 particles. The relative humidity was controlled by saturated salt solutions at ambient temperatures from 298-353 K. Measurements were made using dielectric spectroscopy over the frequency range 10-3-105 Hz. The hydration isotherm (i.e. the mass uptake of water) was established by measuring the mass as a function of relative humidity (RH). It was found that the nanocomposites absorb up to 60% more water than the unfilled and micro-filled epoxies. Dielectric spectroscopy shows different conduction and quasi-DC behaviours at very low frequencies (<10-2 Hz) with activation energies dependent on the hydration and temperature. These observations have led to the development of a “water shell” model to explain this phenomenon

An equations-of-motion approach to quantum mechanics: application to a model phase transition

We present a generalized equations-of-motion method that efficiently calculates energy spectra and matrix elements for algebraic models. The method is applied to a 5-dimensional quartic oscillator that exhibits a quantum phase transition between vibrational and rotational phases. For certain parameters, 10 by 10 matrices give better results than obtained by diagonalising 1000 by 1000 matrices.Comment: 4 pages, 1 figur

Quasi dynamical symmetry in an interacting boson model phase transition

The oft-observed persistence of symmetry properties in the face of strong symmetry-breaking interactions is examined in the SO(5)-invariant interacting boson model. This model exhibits a transition between two phases associated with U(5) and O(6) symmetries, respectively, as the value of a control parameter progresses from 0 to 1. The remarkable fact is that, for intermediate values of the control parameter, the model states exhibit the characteristics of its closest symmetry limit for all but a relatively narrow transition region that becomes progressively narrower as the particle number of the model increases. This phenomenon is explained in terms of quasi-dynamical symmetry.Comment: 4 figure

Prediction of unsteady aerodynamic loadings caused by leading edge and trailing edge control surface motions in subsonic compressible flow: Computer program description

A digital computer program has been developed to calculate unsteady loadings caused by motions of lifting surfaces with leading edge or trailing edge controls based on the subsonic kernel function approach. The pressure singularities at hinge line and side edges have been extracted analytically as a preliminary step to solving the integral equation by collocation. The program calculates generalized aerodynamic forces for user supplied deflection modes. Optional intermediate output includes pressure at an array of points, and sectional generalized forces. From one to six controls on the half span can be accommodated

The Influence of Water on Dielectric Behavior of Silica-filled Epoxy Nano-composites and Percolation Phenomenon

The dielectric properties of epoxy resin were studied as a function of hydration by dielectric spectroscopy. The dielectric spectroscopy measurements show different conduction and quasi-DC behaviors at very low frequencies (<10-2 Hz) with activation energies dependent on the hydration. These observations lead to the development of a model in which a “water shell” is formed around the nano-particles. The multiple shell model, originally proposed by Lewis and developed by Tanaka, has been further developed to explain low frequency dielectric spectroscopy results in which percolation of charge carriers through overlapping water shells was shown to occur. At 100% relative humidity, water is believed to surround the nanoparticles to a depth of approximately 10 monolayers as the first layer. A second layer of water is proposed that is dispersed by sufficiently concentrated to be conductive. If all the water had existed in a single layer surrounding a nanoparticle, this layer would have been approximately 5 nm thick at 100% RH. Filler particles that have surfaces that are functionalized to be hydrophobic considerably reduce the amount of water absorbed in nanocomposites under the same conditions of humidity. PEA results show that the wetted epoxy specimens have a higher threshold field of space charge accumulation than such dry specimens since water enhances charge decay

On giant piezoresistance effects in silicon nanowires and microwires

The giant piezoresistance (PZR) previously reported in silicon nanowires is experimentally investigated in a large number of surface depleted silicon nano- and micro-structures. The resistance is shown to vary strongly with time due to electron and hole trapping at the sample surfaces. Importantly, this time varying resistance manifests itself as an apparent giant PZR identical to that reported elsewhere. By modulating the applied stress in time, the true PZR of the structures is found to be comparable with that of bulk silicon

Allozyme and mitochondrial DNA variability within the New Zealand damselfly genera Xanthocnemis, Austrolestes, and Ischnura (Odonata)

We collected larval damselflies from 17 sites in the North, South and Chatham Islands, and tested the hypotheses that: (1) genetic markers (e.g., allozymes, mtDNA) would successfully ¬discriminate taxa; and (2) the dispersal capabilities of adult damselflies would limit differentiation among locations. Four species from three genera were identified based on available taxonomic keys. Using 11 allozyme loci and the mitochondrial cytochrome c-oxidase subunit I (COI) gene, we confirmed that all taxa were clearly discernible. We found evidence for low to moderate differentiation among locations based on allozyme (mean FST = 0.09) and sequence (COI) divergence (<0.034). No obvious patterns with respect to geographic location were detected, although slight differences were found between New Zealand’s main islands (North Island, South Island) and the Chatham Islands for A. colensonis (sequence divergence 0.030–0.034). We also found limited intraspecific genetic variability based on allozyme data (Hexp < 0.06 in all cases). We conclude that levels of gene flow/dispersal on the main islands may have been sufficient to maintain the observed homogeneous population structure, and that genetic techniques, particularly the COI gene locus, will be a useful aid in future identifications