Cerámicas eutécticas solidificadas direccionalmente para fotónica y electrocerámica

40 páginas, 10 figuras, 3 tablas.[ES] Se describe la microestructura de eutécticos de óxidos y fluoruros que se obtienen mediante diversos procedimientos de solidificación direccional. El artículo revisa las propiedades ópticas y la conductividad de estos materiales haciendo hincapié sobre todo en la influencia que su microestructura tiene en dichas propiedades. La investigación en este campo ha sido realizada fundamentalmente durante los últimos 20 años..[EN] We describe the microstructure of oxide and fluoride eutectics produced by diverse methods of directional solidification. The article reviews the optical properties and ionic conductivity of the materials with special emphasis on the influence of microstructure on those properties. The research in this field has been performed mainly along the last 20 years.Agradezco la financiación del Ministerio de Educación y Ciencia a través de los proyectos MAT2003-01182 y MAT2003-06085-C03-01.Peer reviewe

Low-thrust chemical propulsion system propellant expulsion and thermal conditioning study. Executive summary

Preferred techniques for providing abort pressurization and engine feed system net positive suction pressure (NPSP) for low thrust chemical propulsion systems (LTPS) were determined. A representative LTPS vehicle configuration is presented. Analysis tasks include: propellant heating analysis; pressurant requirements for abort propellant dump; and comparative analysis of pressurization techniques and thermal subcoolers

Low-thrust chemical propulsion system propellant expulsion and thermal conditioning study

Thermal conditioning systems for satisfying engine net positive suction pressure (NPSP) requirements, and propellant expulsion systems for achieving propellant dump during a return-to-launch site (RTLS) abort were studied for LH2/LO2 and LCH4/LO2 upper stage propellant combinations. A state-of-the-art thermal conditioning system employing helium injection beneath the liquid surface shows the lowest weight penalty for LO2 and LCH4. A technology system incorporating a thermal subcooler (heat exchanger) for engine NPSP results in the lowest weight penalty for the LH2 tank. A preliminary design of two state-of-the-art and two new technology systems indicates a weight penalty difference too small to warrant development of a LH2 thermal subcooler. Analysis results showed that the LH2/LO2 propellant expulsion system is optimized for maximum dump line diameters, whereas the LCH4/LO2 system is optimized for minimum dump line diameter (LCH4) and maximum dump line diameter (LO2). The primary uncertainty is the accurate determination of two-phase flow rates through the dump system; experimentation is not recommended because this uncertainty is not considered significant

Compositionally graded YSZ–NiO composites by surface laser melting

El pdf del artículo es la versión post-print.Laser surface melting has been applied to near eutectic NiO–YSZ sintered ceramics. The objective is to generate a functional gradient composite material with graded microstructure and composition. At low solidification rates the resultant material has a graded composition, with a severe NiO segregation towards the surface. A thick NiO layer whose thickness depends on the travelling speed is formed. Below this layer the microstructure is eutectic like with composition varying with depth. In contact with the ceramic, excess YSZ coming from the hypereutectic composition forms an almost continuous YSZ layer. The thickness of both segregated layers, NiO and YSZ can be controlled by traverse speed. Thickness decreases as travelling speed increases until a limiting travelling rate of 110 mm/h, at which no more segregation is found. Possible causes to explain the relevant NiO segregation towards the surface are discussed.Financial support from the Ministerio de Educación y Ciencia of Spain and the CE program FEDER under grant MAT2006-13005-C03-01 is gratefully acknowledged.Peer Reviewe

Editorial

Víctor Orera was our first teacher and scientific father in the laboratory. With him we also learned that research, like any human activity, must be honest and contribute to improving the world around us. He was very passionate about science, dedicated and naturally optimistic. When we were having a bad day at the lab, he had a knack for finding the silver lining in an apparently unsuccessful outcome. Until retirement, he was the leader of our Research Group, Processing and Characterization of Structural and Functional Ceramics, PROCACEF, at the Institute of Materials Science of Aragon, ICMA, an institute that he contributed to found and develop. ICMA has recently become part of the Aragon Institute of Nanoscience and Materials (INMA), from where we write these words..

Genesis of self-organized zebra textures in burial dolomites: Displacive veins, induced stress, and dolomitization

The dolomite veins making up rhythmites common in burial dolomites are not cement infillings of supposed cavities, as in the prevailing view, but are instead displacive veins, veins that pushed aside the host dolostone as they grew. Evidence that the veins are displacive includes a) small transform-fault-like displacements that could not have taken place if the veins were passive cements, and b) stylolites in host rock that formed as the veins grew in order to compensate for the volume added by the veins. Each zebra vein consists of crystals that grow inward from both sides, and displaces its walls via the local induced stress generated by the crystal growth itself. The petrographic criterion used in recent literature to interpret zebra veins in dolomites as cements - namely, that euhedral crystals can grow only in a prior void - disregards evidence to the contrary. The idea that flat voids did form in dolostones is incompatible with the observed optical continuity between the saddle dolomite euhedra of a vein and the replacive dolomite crystals of the host. The induced stress is also the key to the self-organization of zebra veins: In a set of many incipient, randomly-spaced, parallel veins just starting to grow in a host dolostone, each vein¿s induced stress prevents too-close neighbor veins from nucleating, or redissolves them by pressure-solution. The veins that survive this triage are those just outside their neighbors¿s induced stress haloes, now forming a set of equidistant veins, as observed

Probing high oxygen activity in YSZ electrolyte

The redox behavior of terbium and praseodymium doped yttria-stabilized zirconia (YSZ) is studied. The aim is to identify spectroscopic probes and a suitable experimental procedure to monitor the oxygen activity in YSZ electrolytes in solid oxide cells with spatial resolution and at operation conditions (e.g. at high temperatures). Sintered ceramics and crystals with 0.3 to 10 at% content of Pr or Tb ions in YSZ were prepared. Upon equilibration in atmospheres from 10-20to 100 bar PO2around 800 °C, the majority of these rare earth ions are in the 3 + oxidation state. At oxygen pressures above 0.001 bar, the small proportion of Tb4+and Pr4+formed give rise to intense optical absorption around 300 500 nm and to decreased reflectance. From the reflectance measurements it is shown that the Tb4+concentration increases as PO21/4, as correspond to the trapping of the holes generated upon the oxygen incorporation as Tb4+. This competitive absorption causes a decrease of the Tb3+luminescence. A quantitative relationship of the Tb3+luminescence intensity with PO2at 800 °C has been found, which is compatible with the trapping model. The spatial resolution of the experimental procedure could be very roughly estimated of the order of 100 µm

Procedimiento de preparación y materiales conformados basados en compuestos eutécticos binarios o ternarios de circonia

Referencia OEPM: P9600891.-- Fecha de solicitud: 19/04/1996.-- Titular: Consejo Superior de Investigaciones Científicas (CSIC).Procedimiento de preparación y materiales conformados basados en compuestos eutécticos binarios o ternarios de circonia. La presente invención está relacionada con la preparación de materiales con estructuras eutécticas micrométricas basados en mezclas de óxidos, conformados con dimensiones mili y submilimétricas mediante fusión zonal por láser con diferentes sistemas ópticos de focalización y control de los haces de los láseres. Su utilización es en el sector de la producción y conservación de energía, como elementos calefactores, refractarios, cátodos para plasmas de aire, electrodos, en componentes para celdas de combustión, microsensores de gas oxígeno, etc.Peer reviewe

Laser-assisted surface melting of Al2O3-YSZ eutectic ceramics

[ES] Se presenta un procedimiento para la densificación y/o texturado superficial de cerámicas de Al2O3-YSZ (circona estabilizada con itria) con composición eutéctica mediante fusión zonal asistida por láser. Haciendo un barrido con la radiación proveniente de un láser de potencia sobre piezas cerámicas conseguimos modificar la microestructura y densificar completatmente la capa superficial, con un espesor que va de 30 a 1000 μm. Por ejemplo, con línea estrecha de láser de diodo, fluencia de 1.23 kW/cm2 y velocidades de barrido de 0.14 mm/s, solidificamos capas de 560 μm. El resultado es una superficie de baja rugosidad y no porosa. La microestructura de la muestra es fina debido a su composición eutéctica. La interfase sólido-líquido en el proceso de crecimiento determina la orientación de la microestructura. Se estudia la forma de esta interfase tanto en cortes transversales como longitudinales, lo que permite analizar el efecto que sobre la microestructura tiene la superposición de barridos, que es una alternativa para tratar superficies extensas. Macroscópicamente la frontera entre barridos contiguos es suave. Sin embargo, su microestructura presenta discontinuidad en el espaciado entre las fases debido a la evolución microestructural en la región no fundida sometida a altas temperaturas y a la nucleación preferencial de Al2O3 al comenzar el crecimiento cristalino. Se analizan distintas posibilidades para disminuir el choque térmico inherente al proceso y que conduce a la formación de grietas paralelas a la dirección de procesado y de delaminación. Se observa una mejora importante cuando se precalienta la pieza a tratar, de modo que es posible procesar superficies de cerámicas eutécticas 99% densas.[EN] A procedure for surface densification and/or texturing of Al2O3-YSZ (yttria stabilised zirconia) ceramics with eutectic composition by means of laser surface melting is presented. By scanning a high-power laser beam on a ceramic surface, we achieve a textured and fully dense surface layer from 30 to 1000 microns thick. For example, using a thin diode laser line with fluence 1.23 kW/cm2 and 0.14 mm/s scan rate, the solidified layer has 560 μm depth. We get a low roughness and dense surface. The microstructure is fine (micron size) due to the eutectic composition. The orientation of the microstructure is determined by the shape of the solid-liquid interface in the solidification process. We study the shape of this interface in transverse and longitudinal cross-sections in single as well as overlapping scans, which are required to process large surfaces. From the macroscopic point of view, the transition between adjacent scans is smooth. However, the microstructure presents discontinuity in the interphase spacing due to microstructural evolution in the heat affected region as well as the nucleation of an Al2O3 layer at the beginning of the crystal growth. The thermal shock inherent to the procedure generates cracks longitudinal and transverse to the scanning direction, as well as delaminating cracks. We analyse different possibilities to reduce this thermal shock. The best results are obtained by preheating the substrate, allowing us to process surfaces of Al2O3-YSZ eutectic ceramics 99% dense.Financiación del Ministerio de Ciencia y Tecnología a través de los proyectos MAT2000-1495 y MAT2000-1533-C03-02.Peer reviewe