1,745 research outputs found
Impact of UV wavelength and curing time on the properties of spin-coated low-k films
Advanced spin-on k 2.3 films with similar to 40% porosity were enabled by liquid phase self-assembly (LPSA) mechanism on Si substrates. UV-assisted thermal template removal is investigated as a faster alternative to the conventional thermal process. The as-deposited films were exposed to narrow-band UV light of 172 nm, 222 nm, 254 nm or 185/254 nm at 400 degrees C for different time. The optical, mechanical, chemical and electrical properties of the resulting films are discussed in this work. Photons with wavelength of about 172 nm from one side are detrimental to the electrical and chemical properties of the low-k films hut from the other side notably improve the porous low-k mechanical properties. Exposure to 222 nm light as short as 3 min, is more efficient in terms of template removal when compared to 2h thermal cure, while in both cases similar mechanical and electrical properties are reported. UV-cure using 254 nm or dual band 254/185 nm photons seem to have a minor contribution to the template removal efficiency for the applied doses. Higher doses are necessary in order to better understand the effective contribution of these photon energies. Finally, the HF etching mechanism is discussed
Prevalence of qacA/B genes and mupirocin resistance among methicillin-resistant Staphylococcus aureus (MRSA) isolates in the setting of chlorhexidine bathing without mupirocin
OBJECTIVE: We aimed to determine the frequency of qacA/B chlorhexidine tolerance genes and high-level mupirocin resistance among MRSA isolates before and after the introduction of a chlorhexidine (CHG) daily bathing intervention in a surgical intensive care unit (SICU). DESIGN: Retrospective cohort study (2005–2012) SETTING: A large tertiary-care center PATIENTS: Patients admitted to SICU who had MRSA surveillance cultures of the anterior nares METHODS: A random sample of banked MRSA anterior nares isolates recovered during (2005) and after (2006–2012) implementation of a daily CHG bathing protocol was examined for qacA/B genes and high-level mupirocin resistance. Staphylococcal cassette chromosome mec (SCCmec) typing was also performed. RESULTS: Of the 504 randomly selected isolates (63 per year), 36 (7.1%) were qacA/B positive ( + ) and 35 (6.9%) were mupirocin resistant. Of these, 184 (36.5%) isolates were SCCmec type IV. There was a significant trend for increasing qacA/B (P= .02; highest prevalence, 16.9% in 2009 and 2010) and SCCmec type IV (P< .001; highest prevalence, 52.4% in 2012) during the study period. qacA/B( + ) MRSA isolates were more likely to be mupirocin resistant (9 of 36 [25%] qacA/B( + ) vs 26 of 468 [5.6%] qacA/B(−); P= .003). CONCLUSIONS: A long-term, daily CHG bathing protocol was associated with a change in the frequency of qacA/B genes in MRSA isolates recovered from the anterior nares over an 8-year period. This change in the frequency of qacA/B genes is most likely due to patients in those years being exposed in prior admissions. Future studies need to further evaluate the implications of universal CHG daily bathing on MRSA qacA/B genes among hospitalized patients
Recommended from our members
Nanoscale patterning of self-assembled monolayer (SAM)-functionalised substrates with single molecule contact printing
Defined arrangements of individual molecules are covalenty connected ("printed") onto SAM-functionalised gold substrates with nanometer resolution. Substrates were initially pre-functionlised by coating with 3,3′-dithiodipropionic acid (DTPA) to form a self-assembled monolayer (SAM), which was characterised by atomic force microscopy (AFM), contact angle goniometry, cyclic voltammetry and surface plasmon resonance (SPR) spectroscopy. Pre-defined "ink" patterns displayed on DNA origami-based single-use carriers ("stamp") were covalently conjugated to the SAM using 1-ethyl-3-(3-dimethylamino-propyl)carbodiimide (EDC) and N-hydroxy-succinimide (NHS). These anchor points were used to create nanometer-precise single-molecule arrays, here with complementary DNA and streptavidin. Sequential steps of the printing process were evaluated by AFM and SPR spectroscopy. It was shown that 30% of the detected arrangements closely match the expected length distribution of designed patterns, whereas another 40% exhibit error within the range of only 1 streptavidin molecule. SPR results indicate that imposing a defined separation between molecular anchor points within the pattern through this printing process enhances the efficiency for association of specific binding partners for systems with high sterical hindrance. This study expands upon earlier findings where geometrical information was conserved by the application of DNA nanostructures, by establishing a generalisable strategy which is universally applicable to nearly any type of prefunctionalised substrate such as metals, plastics, silicates, ITO or 2D materials
The Use of Indicators in Agri-environmental Managemanent in the Netherlands
This report represents part of the research carried out in the Landscape Partners Project which aims to identify, analyse and assess the contribution of multi-stakeholder partnerships to the sustainable management of rural landscapes and to the well-being of communities. For the Dutch case study, the investigation focussed on Agrarische Natuurverenigingen (ANVs). They are agri-environmental collaborative groups which were selected because they represent a mix of stakeholders, including farmers, citizens, municipalities and nature conservation interest
Liesegang patterns: Effect of dissociation of the invading electrolyte
The effect of dissociation of the invading electrolyte on the formation of
Liesegang bands is investigated. We find, using organic compounds with known
dissociation constants, that the spacing coefficient, 1+p, that characterizes
the position of the n-th band as x_n ~ (1+p)^n, decreases with increasing
dissociation constant, K_d. Theoretical arguments are developed to explain
these experimental findings and to calculate explicitly the K_d dependence of
1+p.Comment: RevTex, 8 pages, 3 eps figure
Mechanical Properties of ZTO, ITO, and a-Si:H Multilayer Films for Flexible Thin Film Solar Cells
The behavior of bi- and trilayer coating systems for flexible a-Si:H based solar cells consisting of a barrier, an electrode, and an absorption layer is studied under mechanical load. First, the film morphology, stress, Young’s modulus, and crack onset strain (COS) were analyzed for single film coatings of various thickness on polyethylene terephthalate (PET) substrates. In order to demonstrate the role of the microstructure of a single film on the mechanical behavior of the whole multilayer coating, two sets of InSnOx (indium tin oxide, ITO) conductive coatings were prepared. Whereas a characteristic grain–subgrain structure was observed in ITO-1 films, grain growth was suppressed in ITO-2 films. ITO-1 bilayer coatings showed two-step failure under tensile load with cracks propagating along the ITO-1/a-Si:H-interface, whereas channeling cracks in comparable bi- and trilayers based on amorphous ITO-2 run through all constituent layers. A two-step failure is preferable from an application point of view, as it may lead to only a degradation of the performance instead of the ultimate failure of the device. Hence, the results demonstrate the importance of a fine-tuning of film microstructure not only for excellent electrical properties, but also for a high mechanical performance of flexible devices (e.g., a-Si:H based solar cells) during fabrication in a roll-to-roll process or under service
Onset of entanglement
We have developed a theory of polymer entanglement using an extended
Cahn-Hilliard functional, with two extra terms. One is a nonlocal attractive
term, operating over mesoscales, which is interpreted as giving rise to
entanglement, and the other a local repulsive term indicative of excluded
volume interactions. We show how such a functional can be derived using notions
from gauge theory. We go beyond the Gaussian approximation, to the one-loop
level, to show that the system exhibits a crossover to a state of entanglement
as the average chain length between points of entanglement decreases. This
crossover is marked by critical slowing down, as the effective diffusion
constant goes to zero. We have also computed the tensile modulus of the system,
and we find a corresponding crossover to a regime of high modulus.Comment: 18 pages, with 4 figure
Recommended from our members
Mechanical Properties of ZTO, ITO, and a-Si:H Multilayer Films for Flexible Thin Film Solar Cells
The behavior of bi- and trilayer coating systems for flexible a-Si:H based solar cells consisting of a barrier, an electrode, and an absorption layer is studied under mechanical load. First, the film morphology, stress, Young’s modulus, and crack onset strain (COS) were analyzed for single film coatings of various thickness on polyethylene terephthalate (PET) substrates. In order to demonstrate the role of the microstructure of a single film on the mechanical behavior of the whole multilayer coating, two sets of InSnOx (indium tin oxide, ITO) conductive coatings were prepared. Whereas a characteristic grain–subgrain structure was observed in ITO-1 films, grain growth was suppressed in ITO-2 films. ITO-1 bilayer coatings showed two-step failure under tensile load with cracks propagating along the ITO-1/a-Si:H-interface, whereas channeling cracks in comparable bi- and trilayers based on amorphous ITO-2 run through all constituent layers. A two-step failure is preferable from an application point of view, as it may lead to only a degradation of the performance instead of the ultimate failure of the device. Hence, the results demonstrate the importance of a fine-tuning of film microstructure not only for excellent electrical properties, but also for a high mechanical performance of flexible devices (e.g., a-Si:H based solar cells) during fabrication in a roll-to-roll process or under service
Improved timed-mating, non-invasive method using fewer unproven female rats with pregnancy validation via early body mass increases
For studies requiring accurate conception-timing, reliable, efficient methods of detecting oestrus reduce time and costs, whilst improving welfare. Standard methods use vaginal cytology to stage cycle, and breeders are paired–up using approximately five proven females with proven males to achieve at least one conception on a specific day. We describe an alternative, fast, consistent, non-invasive method of timed-mating using detection of lordosis behaviour in Wistar and Lister-Hooded rats that used unproven females with high success rates. Rats under reverse-lighting had body masses recorded pre-mating, day (d) 3-4, d8, d10 and d18 of pregnancy. Using only the presence of the oestrus dance to time-mate females for 24-hrs, 89% Wistar and 88% Lister-Hooded rats successfully conceived. We did not observe behavioural oestrus in Sprague-Dawleys without males present. Significant body mass increases following mating distinguished pregnant from non-pregnant rats, as early as d4 of pregnancy (10% ± 1.0 increase cf 3% ± 1.2). The pattern of increases throughout gestation was similar for all pregnant rats until late pregnancy, when there were smaller increases for primi- and multiparous rats (32% ± 2.5; 25% ± 2.4), whereas nulliparous rats had highest gains (38% ± 1.5). This method demonstrated a distinct refinement of the previous timed-mating common practice used, as disturbance of females was minimised. Only the number required of nulli-, primi- or multiparous rats were mated, and body mass increases validated pregnancy status. This new breeding-management method is now established practice for two strains of rat and resulted in a reduction in animal use
Band Formation during Gaseous Diffusion in Aerogels
We study experimentally how gaseous HCl and NH_3 diffuse from opposite sides
of and react in silica aerogel rods with porosity of 92 % and average pore size
of about 50 nm. The reaction leads to solid NH_4Cl, which is deposited in thin
sheet-like structures. We present a numerical study of the phenomenon. Due to
the difference in boundary conditions between this system and those usually
studied, we find the sheet-like structures in the aerogel to differ
significantly from older studies. The influence of random nucleation centers
and inhomogeneities in the aerogel is studied numerically.Comment: 7 pages RevTex and 8 figures. Figs. 4-8 in Postscript, Figs. 1-3 on
request from author
- …