Effect of Process Variables on Mechanical and Transport Properties of Carbon Fibers from Mesophase Pitch

To obtain mesophase pitch-based carbon fibers with improved mechanical strength while retaining superior electrical and thermal properties by i) Systematic investigation of the relationship between DDR versus longitudinal and transverse microstructure of mesophase MP fibers; and ii) Developing a novel type of microstructur

Surface Anchoring of Nematic Phase on Carbon Nanotubes: Nanostructure of Ultra-High Temperature Materials

Nuclear energy is a dependable and economical source of electricity. Because fuel supply sources are available domestically, nuclear energy can be a strong domestic industry that can reduce dependence on foreign energy sources. Commercial nuclear power plants have extensive security measures to protect the facility from intruders [1]. However, additional research efforts are needed to increase the inherent process safety of nuclear energy plants to protect the public in the event of a reactor malfunction. The next generation nuclear plant (NGNP) is envisioned to utilize a very high temperature reactor (VHTR) design with an operating temperature of 650-1000ðC [2]. One of the most important safety design requirements for this reactor is that it must be inherently safe, i.e., the reactor must shut down safely in the event that the coolant flow is interrupted [2]. This next-generation Gen IV reactor must operate in an inherently safe mode where the off-normal temperatures may reach 1500ðC due to coolant-flow interruption. Metallic alloys used currently in reactor internals will melt at such temperatures. Structural materials that will not melt at such ultra-high temperatures are carbon/graphtic fibers and carbon-matrix composites. Graphite does not have a measurable melting point; it is known to sublime starting about 3300ðC. However, neutron radiation-damage effects on carbon fibers are poorly understood. Therefore, the goal of this project is to obtain a fundamental understanding of the role of nanotexture on the properties of resulting carbon fibers and their neutron-damage characteristics. Although polygranular graphite has been used in nuclear environment for almost fifty years, it is not suitable for structural applications because it do not possess adequate strength, stiffness, or toughness that is required of structural components such as reaction control-rods, upper plenum shroud, and lower core-support plate [2,3]. For structural purposes, composites consisting of strong carbon fibers embedded in a carbon matrix are needed. Such carbon/carbon (C/C) composites have been used in aerospace industry to produce missile nose cones, space shuttle leading edge, and aircraft brake-pads. However, radiation-tolerance of such materials is not adequately known because only limited radiation studies have been performed on C/C composites, which suggest that pitch-based carbon fibers have better dimensional stability than that of polyacrylonitrile (PAN) based fibers [4]. The thermodynamically-stable state of graphitic crystalline packing of carbon atoms derived from mesophase pitch leads to a greater stability during neutron irradiation [5]. The specific objectives of this project were: (i) to generating novel carbonaceous nanostructures, (ii) measure extent of graphitic crystallinity and the extent of anisotropy, and (iii) collaborate with the Carbon Materials group at Oak Ridge National Lab to have neutron irradiation studies and post-irradiation examinations conducted on the carbon fibers produced in this research project

MICRO‐TEXTURED BORON NITRIDE NANOPLATELET MODIFIED POLYETHYLENE FILMS

Linear low density polyethylene (LLDPE) micro‐textured films filled with boron nitride nanoplatelets (BNN) were produced by continuous melt extrusion. Nanoparticles displayed a significant extent of dispersion inside the matrix. The addition of BNN led to more than 10‐fold increase of the in‐plane thermal conductivity (TC) of the nanocomposite (7.7 W/m.K vs 0.3 W/m.K for pure LLDPE), and 1.3‐fold increase of through thickness TC. To increase the surface area available for convective heat transfer, micro‐textured films (T‐BNN) were produced from a micro‐patterned die. Nanoplatelets were aligned parallel to the film machine direction. Film stiffness and tensile strength are comparable to the base LLDPE. Textures and BNN lubricant property helped to decrease the coefficientof friction

Surface Anchoring of Nematic Phase on Carbon Nanotubes: Nanostructure of Ultra-High Temperature Materials

Nuclear energy is a dependable and economical source of electricity. Because fuel supply sources are available domestically, nuclear energy can be a strong domestic industry that can reduce dependence on foreign energy sources. Commercial nuclear power plants have extensive security measures to protect the facility from intruders [1]. However, additional research efforts are needed to increase the inherent process safety of nuclear energy plants to protect the public in the event of a reactor malfunction. The next generation nuclear plant (NGNP) is envisioned to utilize a very high temperature reactor (VHTR) design with an operating temperature of 650-1000ðC [2]. One of the most important safety design requirements for this reactor is that it must be inherently safe, i.e., the reactor must shut down safely in the event that the coolant flow is interrupted [2]. This next-generation Gen IV reactor must operate in an inherently safe mode where the off-normal temperatures may reach 1500ðC due to coolant-flow interruption. Metallic alloys used currently in reactor internals will melt at such temperatures. Structural materials that will not melt at such ultra-high temperatures are carbon/graphtic fibers and carbon-matrix composites. Graphite does not have a measurable melting point; it is known to sublime starting about 3300ðC. However, neutron radiation-damage effects on carbon fibers are poorly understood. Therefore, the goal of this project is to obtain a fundamental understanding of the role of nanotexture on the properties of resulting carbon fibers and their neutron-damage characteristics. Although polygranular graphite has been used in nuclear environment for almost fifty years, it is not suitable for structural applications because it do not possess adequate strength, stiffness, or toughness that is required of structural components such as reaction control-rods, upper plenum shroud, and lower core-support plate [2,3]. For structural purposes, composites consisting of strong carbon fibers embedded in a carbon matrix are needed. Such carbon/carbon (C/C) composites have been used in aerospace industry to produce missile nose cones, space shuttle leading edge, and aircraft brake-pads. However, radiation-tolerance of such materials is not adequately known because only limited radiation studies have been performed on C/C composites, which suggest that pitch-based carbon fibers have better dimensional stability than that of polyacrylonitrile (PAN) based fibers [4]. The thermodynamically-stable state of graphitic crystalline packing of carbon atoms derived from mesophase pitch leads to a greater stability during neutron irradiation [5]. The specific objectives of this project were: (i) to generating novel carbonaceous nanostructures, (ii) measure extent of graphitic crystallinity and the extent of anisotropy, and (iii) collaborate with the Carbon Materials group at Oak Ridge National Lab to have neutron irradiation studies and post-irradiation examinations conducted on the carbon fibers produced in this research project

Processing of Carbon Fiber Reinforced Composites by Three Dimensional Photolithography

The reinforcement of photoresins with continuous carbon fibers is discussed in this paper. The processing was conducted in an automated desktop photolithography unit (ADPU) developed and built in-house. Continuous fibers were added in situ to the photoresin to obtain composite samples containing over 20 vol% of the fibers. The tensile strength of these composites improved by at least a factor of 2 as compared to that of the pure photoresins. It is also noted that the photoresin could be partially cured to develop sufficient green strength in the composite samples even though the fibers are opaque to ultraviolet radiation. These results indicate the potential of this technique to produce functional composite components in conjunction with a 3-D photolithography apparatus.Mechanical Engineerin

Fabrication and Analysis of Soy Flour Filled Polyethylene Fibers

Fibers composed of soy flour (soy) and linear low density polyethylene (PE) were produced by melt spinning method. The mixing time of soy flour and PE was adjusted to get better dispersion of soy flour inside the matrix. The inclusion of soy decreased tensile modulus by 35% and tensile strength by 30% of the fibers compared with 950 MPa and 43 MPa, respectively, for PE fibers. Strain to failure for soy-PE fibers was 292% where PE fibers have strain to failure at 513%. Tensile properties of soy-PE fibers are comparable to those of pure PE. Even washing did not deteriorated the tensile properties, significantly. Microstructural analysis showed that fibers have a well morphology without phase distinction. Soy was dispersed well inside PE matrix with little agglomeration

Prediction of Mold Spoilage for Soy/Polyethylene Composite Fibers

Mold spoilage was determined over 109 days on soy/PE fibers held under controlled temperatures (T) ranging from 10°C to 40°C and water activities (aw) from 0.11 to 0.98. Water activities were created in sealed containers using saturated salt solutions and placed in temperature-controlled incubators. Soy/PE fibers that were held at 0.823 aw or higher exhibited mold growth at all temperatures. As postulated, increased water activity (greater than 0.89) and temperature (higher than 25°C) accelerated mold growth on soy/PE fibers. A slower mold growth was observed on soy/PE fibers that were held at 0.87 aw and 10°C. A Weibull model was employed to fit the observed logarithmic values of T, aw, and an interaction term log⁡T×log⁡aw and was chosen as the final model as it gave the best fit to the raw mold growth data. These growth models predict the expected mold-free storage period of soy/PE fibers when exposed to various environmental temperatures and humidities

Fluorescent patterning of paper through laser engraving

While thermal treatment of paper can lead to the formation of aromatic structures via hydrothermal treatment (low temperature) or pyrolysis (high temperature), neither of these approaches allow patterning the substrates. Somewhere in between these two extremes, a handful of research groups have used CO2 lasers to pattern paper and induce carbonization. However, none of the previously reported papers have focused on the possibility to form fluorescent derivatives via laser-thermal engraving. Exploring this possibility, this article describes the possibility of using a CO2 laser engraver to selectively treat paper, resulting in the formation of fluorescent compounds, similar to those present on the surface of carbon dots. To determine the most relevant variables controlling this process, 3 MM chromatography paper was treated using a standard 30 W CO2 laser engraver. Under selected experimental conditions, a blue fluorescent pattern was observed when the substrate was irradiated with UV light (365 nm). The effect of various experimental conditions (engraving speed, engraving power, and number of engraving steps) was investigated to maximize the fluorescence intensity. Through a comprehensive characterization effort, it was determined that 5-(hydroxymethyl)furfural and a handful of related compounds were formed (varying in amount) under all selected experimental conditions. To illustrate the potential advantages of this strategy, that could complement those applications traditionally developed from carbon dots (sensors, currency marking, etc.), a redox-based optical sensor for sodium hypochlorite was developed.Fil: Clark, Kaylee M.. Clemson University; Estados UnidosFil: Skrajewski, Lauren. Clemson University; Estados UnidosFil: Benavidez, Tomás Enrique. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Investigaciones en Físico-química de Córdoba. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Instituto de Investigaciones en Físico-química de Córdoba; Argentina. Clemson University; Estados UnidosFil: Mendes, Letícia F.. Universidade de Sao Paulo; BrasilFil: Bastos, Erick L.. Universidade de Sao Paulo; BrasilFil: Dörr, Felipe A.. Universidade de Sao Paulo; BrasilFil: Sachdeva, Rakesh. Clemson University; Estados UnidosFil: Ogale, Amod A.. Clemson University; Estados UnidosFil: Paixão, Thiago R. L. C.. Universidade de Sao Paulo; BrasilFil: Garcia, Carlos D.. Clemson University; Estados Unido