22 research outputs found
Conversion of Waste Marble Powder into a Binding Material
In the marble industry, a lot of marble is wasted in the form of odd blocks of various sizes and slurry consisting of water and micro-fine particles. The slurry on drying converts into powder. Both slurry and powder have adverse effects on the environment. This research is focused on the gainful utilization of waste marble powder (WMP) by converting it into a valuable binding material. For this purpose, WMP and clay were collected, and their physical and chemical properties were determined. A mix of WMP and clay was prepared and burnt at a temperature around 1300 oC. The burnt mix was ground to powder form to get marble cement (MC). The MC was then used in mortar. The compressive and flexural strengths of mortar cubes and prisms were determined. Apart from this, X-ray diffraction (XRD) analysis, thermo-gravimetric analysis (TGA) and scanning electron microscopic (SEM) analysis were also carried out. The chemical composition showed that the MC has 52.5% di-calcium silicate (C2S) and 3.5% tri-calcium silicate (C3S).The compressive strength of MC mortar after 28 days curing is 6.03 MPa, which is higher than M1 mortar of building code of Pakistan (5 MPa). The compressive strength of MC mortar after one year is 20.67 MPa, which is only 17% less than OPC mortar
Utilization of Marble Wastes in Clay Bricks: A Step towards Lightweight Energy Efficient Construction Materials
Marble dust is one of the hazardous byproducts of marble-processing factories and requires planned disposal. Its beneficial use as a construction material will add to the sustainability, and most importantly, might overcome the burden of marble waste disposal. However, the use of marble dust in concrete has a negative impact. Therefore, this research examines various properties related to the utilization of such material in ceramic clay, and therefore its effects on the use of clay bricks are investigated. The research activity covers the categorization of marble dust powder from three different sources: Ziarat in Mohmand Agency, Buneer, and Mullagori (Pakistan). Its utilization in different proportions preparation of bricks is also addressed. Through the partial replacement of clay with marble dust from 0 to 30% by weight with amplification of 5%, seven mix designs are examined. The test result includes Bulk density, water absorption, porosity, thermal insulation, and strength. The partial replacement of clay with marble dust reduced its weight, strength and increased its porosity, water absorption, and thermal insulation. Furthermore, the utilization of marble powder in bricks minimizes soil erosion and reduces pollution to the environment. Doi: 10.28991/cej-2021-03091738 Full Text: PD
The Effects of Osmosis and Thermo-Priming on Salinity Stress Tolerance in Vigna radiata L.
A plant’s response to osmotic stress is a complex phenomenon that causes many abnormal symptoms due to limitations in growth and development or even the loss of yield. The current research aimed to analyze the agronomical, physiological, and biochemical mechanisms accompanying the acquisition of salt resistance in the Vigna radiata L. variety ‘Ramzan’ using seed osmo- and thermopriming in the presence of PEG-4000 and 4 °C under induced salinity stresses of 100 and 150 mM NaCl. Seeds were collected from CCRI, Nowshera, and sowing was undertaken in triplicate at the Department of Botany, Peshawar University, during the 2018–2019 growing season. Rhizospheric soil pH (6.0), E.C (2.41 ds/m), field capacity, and moisture content level were estimated in the present study. We observed from the estimated results that the agronomic characteristics, i.e., shoot fresh weight and shoot dry weight in T9 (4oC + 150 mM NaCl), root fresh weight and root dry weight in T4 (PEG + 100 mM NaCl), shoot moisture content in T5 (PEG + 100 mM NaCl), and root moisture content in T6 (PEG + 150 mM NaCl) were the highest, followed by the lowest in T1 (both shoot and root fresh weights) and T2 (shoot and root dry weights). Similarly, the shoot moisture content was the maximum in T5 and the minimum in T6, and root moisture was the highest in T6. We observed from the estimated results that agronomical parameters including dry masses (T4, T6, T4), leaf area index, germination index, leaf area, total biomass, seed vigor index under treatment T9, and relative water content and water use efficiency during T5 and T6 were the highest. Plant physiological traits such as proline, SOD enhanced by T1, carotenoids in treatment T2, and chlorophyll and protein levels were the highest under treatment T4, whereas sugar and POD were highest under treatments T7 and T8. The principal component analysis enclosed 63.75% of the total variation among all biological components. These estimated results confirmed the positive resistance by Vigna radiata during osmopriming (PEG) and thermopriming (4 °C) on most of the features with great tolerance under a low-saline treatment such as T4 (PEG), T5 (PEG + 100 mM NaCl), T7 (4 °C), and T8 (4 °C + 100 mM NaCl), while it was susceptible in the case of T6 (PEG + 150 mM NaCl) and T9 (4 °C + 150 mM NaCl) to high salt application. We found that the constraining impact of several priming techniques improved low salinity, which was regarded as economically inexpensive and initiated numerous metabolic processes in plants, hence decreasing germination time. The current study will have major applications for combatting the salinity problem induced by climate change in Pakistan
The Effects of Osmosis and Thermo-Priming on Salinity Stress Tolerance in Vigna radiata L.
A plant’s response to osmotic stress is a complex phenomenon that causes many abnormal symptoms due to limitations in growth and development or even the loss of yield. The current research aimed to analyze the agronomical, physiological, and biochemical mechanisms accompanying the acquisition of salt resistance in the Vigna radiata L. variety ‘Ramzan’ using seed osmo- and thermopriming in the presence of PEG-4000 and 4 °C under induced salinity stresses of 100 and 150 mM NaCl. Seeds were collected from CCRI, Nowshera, and sowing was undertaken in triplicate at the Department of Botany, Peshawar University, during the 2018–2019 growing season. Rhizospheric soil pH (6.0), E.C (2.41 ds/m), field capacity, and moisture content level were estimated in the present study. We observed from the estimated results that the agronomic characteristics, i.e., shoot fresh weight and shoot dry weight in T9 (4oC + 150 mM NaCl), root fresh weight and root dry weight in T4 (PEG + 100 mM NaCl), shoot moisture content in T5 (PEG + 100 mM NaCl), and root moisture content in T6 (PEG + 150 mM NaCl) were the highest, followed by the lowest in T1 (both shoot and root fresh weights) and T2 (shoot and root dry weights). Similarly, the shoot moisture content was the maximum in T5 and the minimum in T6, and root moisture was the highest in T6. We observed from the estimated results that agronomical parameters including dry masses (T4, T6, T4), leaf area index, germination index, leaf area, total biomass, seed vigor index under treatment T9, and relative water content and water use efficiency during T5 and T6 were the highest. Plant physiological traits such as proline, SOD enhanced by T1, carotenoids in treatment T2, and chlorophyll and protein levels were the highest under treatment T4, whereas sugar and POD were highest under treatments T7 and T8. The principal component analysis enclosed 63.75% of the total variation among all biological components. These estimated results confirmed the positive resistance by Vigna radiata during osmopriming (PEG) and thermopriming (4 °C) on most of the features with great tolerance under a low-saline treatment such as T4 (PEG), T5 (PEG + 100 mM NaCl), T7 (4 °C), and T8 (4 °C + 100 mM NaCl), while it was susceptible in the case of T6 (PEG + 150 mM NaCl) and T9 (4 °C + 150 mM NaCl) to high salt application. We found that the constraining impact of several priming techniques improved low salinity, which was regarded as economically inexpensive and initiated numerous metabolic processes in plants, hence decreasing germination time. The current study will have major applications for combatting the salinity problem induced by climate change in Pakistan
Photocatalytic degradation of organic dyes and biological potentials of biogenic zinc oxide nanoparticles synthesized using the polar extract of Cyperus scariosus R.Br. (Cyperaceae)
In this study, the polar root extract of Cyperus scariosus R.Br. was used for the biogenic synthesis of ZnO NPs. The results of this study show that ZnO NPs have a spherical structure with an average size of 85.4 nm. The synthesized catalysts were tested for their photocatalytic activity by degrading methyl orange and methylene blue under sunlight. Improved degradation efficiencies of 79.44% and 84.92% were achieved within 120 min. ZnO NPs exhibited strong antibacterial activity against both Gram-positive Listeria monocytogenes (18 mm) and Staphylococcus epidermidis (20 mm) and Gram-negative strains of Escherichia coli (16 mm) and Bordetella bronchiseptica (14 mm), as shown by the inhibition zones, which were comparable to the positive control (ceftriaxone) but larger than the plant root extract. ZnO NPs showed high antioxidant activity, as a ferric-reducing antioxidant power assay value of 66.29 µg (AAE µg·mL−1) and a DPPH value of 57.44 µg (AAE µg·mL−1) were obtained at a concentration of 500 µL, which was higher than those of the C. scariosus root extract. Quantification of the total phenolic and flavonoid content yielded values of 57.63 µg (GAE µg·mL−1) and 70.59 µg (QCE µg·mL−1), respectively. At a concentration of 500 μL (1 mg·mL−1), the tested nanoparticles (NPs) showed a greater anti-inflammatory effect (84.12%) compared to the root extract of C. scariosus (34.39%). Overall, our findings highlight the versatile properties of green synthesized ZnO NPs and demonstrate their potential for environmental remediation and antimicrobial formulations, as well as promising candidates for further investigation in biomedical fields such as drug delivery and therapy
Global age-sex-specific mortality, life expectancy, and population estimates in 204 countries and territories and 811 subnational locations, 1950–2021, and the impact of the COVID-19 pandemic: a comprehensive demographic analysis for the Global Burden of Disease Study 2021
Background: Estimates of demographic metrics are crucial to assess levels and trends of population health outcomes. The profound impact of the COVID-19 pandemic on populations worldwide has underscored the need for timely estimates to understand this unprecedented event within the context of long-term population health trends. The Global Burden of Diseases, Injuries, and Risk Factors Study (GBD) 2021 provides new demographic estimates for 204 countries and territories and 811 additional subnational locations from 1950 to 2021, with a particular emphasis on changes in mortality and life expectancy that occurred during the 2020–21 COVID-19 pandemic period. Methods: 22 223 data sources from vital registration, sample registration, surveys, censuses, and other sources were used to estimate mortality, with a subset of these sources used exclusively to estimate excess mortality due to the COVID-19 pandemic. 2026 data sources were used for population estimation. Additional sources were used to estimate migration; the effects of the HIV epidemic; and demographic discontinuities due to conflicts, famines, natural disasters, and pandemics, which are used as inputs for estimating mortality and population. Spatiotemporal Gaussian process regression (ST-GPR) was used to generate under-5 mortality rates, which synthesised 30 763 location-years of vital registration and sample registration data, 1365 surveys and censuses, and 80 other sources. ST-GPR was also used to estimate adult mortality (between ages 15 and 59 years) based on information from 31 642 location-years of vital registration and sample registration data, 355 surveys and censuses, and 24 other sources. Estimates of child and adult mortality rates were then used to generate life tables with a relational model life table system. For countries with large HIV epidemics, life tables were adjusted using independent estimates of HIV-specific mortality generated via an epidemiological analysis of HIV prevalence surveys, antenatal clinic serosurveillance, and other data sources. Excess mortality due to the COVID-19 pandemic in 2020 and 2021 was determined by subtracting observed all-cause mortality (adjusted for late registration and mortality anomalies) from the mortality expected in the absence of the pandemic. Expected mortality was calculated based on historical trends using an ensemble of models. In location-years where all-cause mortality data were unavailable, we estimated excess mortality rates using a regression model with covariates pertaining to the pandemic. Population size was computed using a Bayesian hierarchical cohort component model. Life expectancy was calculated using age-specific mortality rates and standard demographic methods. Uncertainty intervals (UIs) were calculated for every metric using the 25th and 975th ordered values from a 1000-draw posterior distribution. Findings: Global all-cause mortality followed two distinct patterns over the study period: age-standardised mortality rates declined between 1950 and 2019 (a 62·8% [95% UI 60·5–65·1] decline), and increased during the COVID-19 pandemic period (2020–21; 5·1% [0·9–9·6] increase). In contrast with the overall reverse in mortality trends during the pandemic period, child mortality continued to decline, with 4·66 million (3·98–5·50) global deaths in children younger than 5 years in 2021 compared with 5·21 million (4·50–6·01) in 2019. An estimated 131 million (126–137) people died globally from all causes in 2020 and 2021 combined, of which 15·9 million (14·7–17·2) were due to the COVID-19 pandemic (measured by excess mortality, which includes deaths directly due to SARS-CoV-2 infection and those indirectly due to other social, economic, or behavioural changes associated with the pandemic). Excess mortality rates exceeded 150 deaths per 100 000 population during at least one year of the pandemic in 80 countries and territories, whereas 20 nations had a negative excess mortality rate in 2020 or 2021, indicating that all-cause mortality in these countries was lower during the pandemic than expected based on historical trends. Between 1950 and 2021, global life expectancy at birth increased by 22·7 years (20·8–24·8), from 49·0 years (46·7–51·3) to 71·7 years (70·9–72·5). Global life expectancy at birth declined by 1·6 years (1·0–2·2) between 2019 and 2021, reversing historical trends. An increase in life expectancy was only observed in 32 (15·7%) of 204 countries and territories between 2019 and 2021. The global population reached 7·89 billion (7·67–8·13) people in 2021, by which time 56 of 204 countries and territories had peaked and subsequently populations have declined. The largest proportion of population growth between 2020 and 2021 was in sub-Saharan Africa (39·5% [28·4–52·7]) and south Asia (26·3% [9·0–44·7]). From 2000 to 2021, the ratio of the population aged 65 years and older to the population aged younger than 15 years increased in 188 (92·2%) of 204 nations. Interpretation: Global adult mortality rates markedly increased during the COVID-19 pandemic in 2020 and 2021, reversing past decreasing trends, while child mortality rates continued to decline, albeit more slowly than in earlier years. Although COVID-19 had a substantial impact on many demographic indicators during the first 2 years of the pandemic, overall global health progress over the 72 years evaluated has been profound, with considerable improvements in mortality and life expectancy. Additionally, we observed a deceleration of global population growth since 2017, despite steady or increasing growth in lower-income countries, combined with a continued global shift of population age structures towards older ages. These demographic changes will likely present future challenges to health systems, economies, and societies. The comprehensive demographic estimates reported here will enable researchers, policy makers, health practitioners, and other key stakeholders to better understand and address the profound changes that have occurred in the global health landscape following the first 2 years of the COVID-19 pandemic, and longer-term trends beyond the pandemic
A Question Mark on Emerging Zinc-Related Nutritional Deficiencies in Pakistani Population
Performance of Concrete Confined with a Jute–Polyester Hybrid Fiber Reinforced Polymer Composite: A Novel Strengthening Technique
The strengthening and rehabilitation of concrete members is an important issue which arises worldwide. Carbon, aramid and glass fiber reinforced polymer (FRP) composites are mainly used for strengthening and rehabilitation. However, its use is limited on a small scale because of its high price, lack of availability and environmental impacts. The solution of this issue gives rise to the use of locally available natural fibers and low-cost synthetic fibers. This paper presents the experimental and analytical results of circular and square concrete columns confined with jute–polyester hybrid FRP composites. The main objective of this study is to evaluate the viability and performance of concrete confined with the hybridization of jute and polyester (FRP) composite sheets to utilize its superior properties. A novel hybrid technique has been applied for the wrapping of fiber sheets. The fiber sheets were applied in such a way that a uniform bond between the inner and outer layer was achieved. A total of 32 plain, standard size circular and square concrete specimens, externally wrapped with a jute–polyester FRP (JPFRP) composite, were tested under monotonic axial compressive loads. The result shows that JPFRP confinement increased the strength, strain and ductility index ranged between 1.24 and 2.61, 1.38 and 8.97, and 4.94 and 26.5 times the un-jacketed specimen, respectively. Furthermore, the wrapping has a significant effect on the low-strength specimens, having a circular cross-section. For high strength specimens, the post-peak stress-strain behavior was dominated by the outer polyester jacket because of its large rupture strain. Additionally, the test results were used to evaluate the existing strength-strain models derived for conventional FRPs. The models predicted values either underestimating or overestimating the compressive strength and strain of JPFRP-confined specimens. However, the strength models performed better than the strain models. The JPFRP wrapping significantly enhanced the strength, fracture energy, ductility index, and post-peak response. Therefore, JPFRP confinement can be used for a small-scale application, where little strength and high ductility is demanded. Moreover, it can be used to prevent the peeling of the concrete cover and moisture penetration into the concrete
A Question Mark on Emerging Zinc-Related Nutritional Deficiencies in Pakistani Population
Evaluation of Mechanical and Microstructural Properties and Global Warming Potential of Green Concrete with Wheat Straw Ash and Silica Fume
Cement and concrete are among the major contributors to CO2 emissions in modern society. Researchers have been investigating the possibility of replacing cement with industrial waste in concrete production to reduce its environmental impact. Therefore, the focus of this paper is on the effective use of wheat straw ash (WSA) together with silica fume (SF) as a cement substitute to produce high-performance and sustainable concrete. Different binary and ternary mixes containing WSA and SF were investigated for their mechanical and microstructural properties and global warming potential (GWP). The current results indicated that the binary and ternary mixes containing, respectively, 20% WSA (WSA20) and 33% WSA together with 7% SF (WSA33SF7) exhibited higher strengths than that of control mix and other binary and ternary mixes. The comparative lower apparent porosity and water absorption values of WSA20 and WSA33SF7 among all mixes also validated the findings of their higher strength results. Moreover, SEM–EDS and FTIR analyses has revealed the presence of dense and compact microstructure, which are mostly caused by formation of high-density calcium silicate hydrate (C-S-H) and calcium hydroxide (C-H) phases in both blends. FTIR and TGA analyses also revealed a reduction in the portlandite phase in these mixes, causing densification of microstructures and pores. Additionally, N2 adsorption isotherm analysis demonstrates that the pore structure of these mixes has been densified as evidenced by a reduction in intruded volume and a rise in BET surface area. Furthermore, both mixes had lower CO2-eq intensity per MPa as compared to control, which indicates their significant impact on producing green concretes through their reduced GWPs. Thus, this research shows that WSA alone or its blend with SF can be considered as a source of revenue for the concrete industry for developing high-performance and sustainable concretes