26,839 research outputs found
A study of 35-ghz radar-assisted orbital maneuvering vehicle/space telescope docking
An experiment was conducted to study the effects of measuring range and range rate information from a complex radar target (a one-third scale model of the Edwin P. Hubble Space Telescope). The radar ranging system was a 35-GHz frequency-modulated continuous wave unit developed in the Communication Systems Branch of the Information and Electronic Systems Laboratory at Marshall Space Flight Cneter. Measurements were made over radar-to-target distances of 5 meters to 15 meters to simulate the close distance realized in the final stages of space vehicle docking. The Space Telescope model target was driven by an antenna positioner through a range of azimuth and elevation (pitch) angles to present a variety of visual aspects of the aft end to the radar. Measurements were obtained with and without a cube corner reflector mounted in the center of the aft end of the model. The results indicate that range and range rate measurements are performed significantly more accurately with the cooperative radar reflector affixed. The results further reveal that range rate (velocity) can be measured accurately enough to support the required soft docking with the Space Telescope
An investigation of pre-launch and in-flight STS range safety radio signal degradation and dropout
The range safety system (RSS) transmitters operate at a frequency of 416.500 MHz. The transmitting antennas transmit left circularly polarized waves, and the shuttle range safety system (SRSS) receiving antennas onboard the shuttle vehicle receive left circular polarization. Preliminary explanations are proposed for many of the observed fluctuations in signal levels. It is recommended that experiments and further investigation be performed to test the validity of certain of these explanations
A study of radar cross section measurement techniques
Past, present, and proposed future technologies for the measurement of radar cross section were studied. The purpose was to determine which method(s) could most advantageously be implemented in the large microwave anechoic chamber facility which is operated at the antenna test range site. The progression toward performing radar cross section measurements of space vehicles with which the Orbital Maneuvering Vehicle will be called upon to rendezvous and dock is a natural outgrowth of previous work conducted in recent years of developing a high accuracy range and velocity sensing radar system. The radar system was designed to support the rendezvous and docking of the Orbital Maneuvering Vehicle with various other space vehicles. The measurement of radar cross sections of space vehicles will be necessary in order to plan properly for Orbital Maneuvering Vehicle rendezvous and docking assignments. The methods which were studied include: standard far-field measurements; reflector-type compact range measurements; lens-type compact range measurement; near field/far field transformations; and computer predictive modeling. The feasibility of each approach is examined
Flat-plate solar array project. Volume 1: Executive summary
In 1975, the U.S. Government contracted the Jet Propulsion Lab. to develop, by 1985, in conjunction with industry, the photovoltaics (PV) module and array technology required for widespread use of photovoltaics as a significant terrestrial energy source. As a result, a project that eventually became known as the Flat Plate Solar Array (FSA) Project was formed to manage an industry, university, and Government team to perform the necessary research and development. The original goals were to achieve widespread commercial use of PV modules and arrays through the development of technology that would allow them to be profitably sold for $1.07/peak watts (1985 dollars). A 10% module conversion efficiency and a 20 year lifetime were also goals. It is intended that the executive summary provide the means by which one can gain a perspective on 11 years of terrestrial photovoltaic research and development conducted by the FSA Project
Negative Group Velocity
The group velocity for pulses in an optical medium can be negative at
frequencies between those of a pair of laser-pumped spectral lines. The gain
medium then can amplify the leading edge of a pulse resulting in a time advance
of the pulse when it exits the medium, as has been recently demonstrated in the
laboratory. This effect has been called superluminal, but, as a classical
analysis shows, it cannot result in signal propgation at speeds greater than
that of light in vacuum.Comment: v3 adds discussion of "rephasing", and adds a figure. v4 adds
references to the early history of negative group velocity, and adds a
figure; thanks to Alex Grani
Matthew Baillie's specimens and engravings
In 1799, Matthew Baillie, William Hunter's nephew, published his famous atlas of pathology. It was entitled A Series of Engravings Accompanied with Explanations which are Intended to Illustrate the Morbid Anatomy of Some of the Most Important Parts of the Human Body. The present study aims to match the illustrations to extant specimens in the collections of William and John Hunter, preserved at the University of Glasgow and at the Royal College of Surgeons of England respectively.
Baillie's book contains 10 fasciculi, consisting of 73 plates and 206 figures. The specimens Baillie illustrated came from his own collection and those of ten others, including his uncles, William and John Hunter. The book was illustrated by William Clift and engraved by James Basire, William Skelton and James Heath.
Excluding eight illustrations of intestinal worms where the provenance of the specimens is uncertain, a total of 98 specimens from William Hunter's collection were illustrated in 104 figures. Eight of the specimens were calculi impossible to identify specifically. Excluding worms and calculi, 72 of William Hunter's specimens illustrated by Baillie are extant in the Hunterian Collection at the University of Glasgow. All but one of the 20 specimens illustrated that had belonged to John Hunter were identified in the on-line catalogue of the Royal College of Surgeons of England. Baillie's own collection was destroyed when the Royal College of Surgeons of England was bombed in 1941. Baillie is credited with being the first to produce an illustrated systematic textbook of morbid anatomy and probably the first to illustrate emphysema and transposition of the great vessels. His book, however, was not comprehensive. It did not cover a number of topics such as muscles and bones and there is little coverage of the nervous system. Baillie's book, however, was an original concept as an atlas of morbid anatomy and showed his deep insight into pathology
Recommended from our members
The mechanism of anaphase spindle elongation: uncoupling of tubulin incorporation and microtubule sliding during in vitro spindle reactivation.
To study tubulin polymerization and microtubule sliding during spindle elongation in vitro, we developed a method of uncoupling the two processes. When isolated diatom spindles were incubated with biotinylated tubulin (biot-tb) without ATP, biot-tb was incorporated into two regions flanking the zone of microtubule overlap, but the spindles did not elongate. After biot-tb was removed, spindle elongation was initiated by addition of ATP. The incorporated biot-tb was found in the midzone between the original half-spindles. The extent and rate of elongation were increased by preincubation in biot-tb. Serial section reconstruction of spindles elongating in tubulin and ATP showed that the average length of half-spindle microtubules increased due to growth of microtubules from the ends of native microtubules. The characteristic packing pattern between antiparallel microtubules was retained even in the new overlap region. Our results suggest that the forces required for spindle elongation are generated by enzymes in the overlap zone that mediate the sliding apart of antiparallel microtubules, and that tubulin polymerization does not contribute to force generation. Changes in the extent of microtubule overlap during spindle elongation were affected by tubulin and ATP concentration in the incubation medium. Spindles continued to elongate even after the overlap zone was composed entirely of newly polymerized microtubules, suggesting that the enzyme responsible for microtubule translocation either is bound to a matrix in the spindle midzone, or else can move on one microtubule toward the spindle midzone and push another microtubule of opposite polarity toward the pole
A permeabilized cell model for studying cell division: a comparison of anaphase chromosome movement and cleavage furrow constriction in lysed PtK1 cells.
After lysis in a Brij 58-polyethylene glycol medium, PtK1 cells are permeable to small molecules, such as erythrosin B, and to proteins, such as rhodamine-labeled FAB, myosin subfragment-1, and tubulin. Holes are present in the plasma membrane, and the mitochondria are swollen and distorted, but other membrane-bounded organelles of the lysed cell model are not noticeably altered. After lysis, the mitotic apparatus is functional; chromosomes move poleward and the spindle elongates. Cells lysed while in cytokinesis will continue to divide for several minutes. Addition of crude tubulin extracts, MAP-free tubulin, or taxol to the lysis medium retards anaphase chromosome movements but does not affect cleavage. On the other hand, N-ethylmaleimide-modified myosin subfragment-1, phalloidin, and cytochalasin B inhibit cleavage but have no effect on anaphase chromosome movements under identical lysis conditions. These results suggest that actomyosin plays no functional role in anaphase chromosome movement in mammalian tissue culture cells and that microtubule depolymerization is a rate-limiting step for chromosome-to-pole movements
- …