Ultrasound Driven Biofilm Removal for Stable Power Generation in Microbial Fuel Cell

Anodic biofilm plays a crucial role in bioelectrochemical system to make it sustainable for long-term performance. However, the accumulation of dead cells over time within the anode biofilm can be particularly detrimental for current generation. In this study, the effect of ultrasound on anode biofilm thickness was investigated in microbial fuel cells (MFCs). Ultrasonic treatment was employed for different durations to evaluate its ability to control the thickness of the biofilm to maintain stable power generation. Cell viability count and field emission scanning electron microscopy (FESEM) analysis of the biofilms over time showed that the number of dead cells increased with the increase of biofilm thickness, and eventually exceeded the number of live cells by many-fold. Electrochemical impedance spectroscopy (EIS) analysis indicated that the high polarization resistance appeared due to the dead layer formation, and thus the catalytic efficiency was reduced in MFCs. The stable power generation was achieved by employing ultrasonic treatment for 30 min every 6 days with some initial exception. The low frequency ultrasound treatment successfully dislodged the ineffective biofilm from the surface of the anode. Moreover, the ultrasound could increase the mass transfer rate of the nutrients and cellular waste through the biofilm leading to the increase in cell growth. Therefore, ultrasonic treatment is verified as an efficient method to control the thickness of the biofilm as well as enhance the cell viability in biofilm thereby maintaining the stable power generation in the MFC

Application of Electroporation Technique in Biofuel Processing

Biofuels production is mostly oriented with fermentation process, which requires fermentable sugar as nutrient for microbial growth. Lignocellulosic biomass (LCB) represents the most attractive, low-cost feedstock for biofuel production, it is now arousing great interest. The cellulose that is embedded in the lignin matrix has an insoluble, highly-crystalline structure, so it is difficult to hydrolyze into fermentable sugar or cell protein. On the other hand, microbial lipid has been studying as substitute of plant oils or animal fat to produce biodiesel. It is still a great challenge to extract maximum lipid from microbial cells (yeast, fungi, algae) investing minimum energy. Electroporation (EP) of LCB results a significant increase in cell conductivity and permeability caused due to the application of an external electric field. EP is required to alter the size and structure of the biomass, to reduce the cellulose crystallinity, and increase their porosity as well as chemical composition, so that the hydrolysis of the carbohydrate fraction to monomeric sugars can be achieved rapidly and with greater yields. Furthermore, EP has a great potential to disrupt the microbial cell walls within few seconds to bring out the intracellular materials (lipid) to the solution. Therefore, this study aims to describe the challenges and prospect of application of EP technique in biofuels processing

Augmentation of Air Cathode Microbial Fuel Cell Performance using Wild Type Klebsiella Variicola

In the present work, simultaneous power generation and wastewater treatment in the single chamber air cathode microbial fuel cell (MFC) have been enhanced by introducing wild-type Klebsiella variicola (K. variicola) as an efficient inoculum for the anode operated with palm oil mill effluent (POME). K. variicola was isolated from municipal wastewater (MWW) and identified using BIOLOG gene III analysis, PCR and sequencing. The performance of K. variicola in MFC was evaluated by polarization curve measurement, electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) analysis. The MFC with K. variicola achieved a maximum power density of about 1.7 W m−3 which is comparatively higher than most widely used anaerobic sludge (215 mW m−3) as an inoculum whereas COD removal efficiency is (43%) lower than anaerobic sludge (74%). Moreover, K. variicola has the ability to produce electron shuttles and to form biofilms on the electrode surface which helps to significantly reduce the anode charge transfer (Rct) resistance compared to the anaerobic sludge. These results revealed the potential of K. variicola to be used in MFC

Carbon Nanotube-Modified MnO2: An Efficient Electrocatalyst for Oxygen Reduction Reaction

In this work, manganese dioxide/carbon nanotube (MnO2/CNT) have been synthesized by sonochemical-coprecipitation method and demonstrated that it could be an effective electrocatalyst for oxygen reduction reaction (ORR). Moreover, the effect of CNT inclusion with MnO2 was also investigated for ORR. The physical and electrochemical properties of the MnO2/CNT were examined by powder X-ray diffraction (XRD), Fourier Transform Infrared (FT-IR) spectroscopy, Brunauer-Emmett-Teller (BET), Transmission Electron Microscopy (TEM), Field Emission Scanning Electron Microscopy/Energy Dispersive X-ray (FESEM/EDX), Cyclic Voltammetry (CV), Electrochemical Impedance Spectroscopy (EIS), Mott-Schottky and Rotating Disk Electrode (RDE) analysis. CV showed higher currents for the ORR in MnO2/CNT than CNT; however, ORR current dropped when the MnO2 loading was increased from 20–40 %. The EIS analysis showed that charge-transfer resistance for MnO2/CNT was significantly lower compared to the MnO2 indicating that MnO2 has good contact with CNT and the composite possess high electrical conductivity. Mott-Schottky results demonstrated that incorporation of CNT into MnO2 resulted in producing larger electron density in n-type MnO2/CNT compared to MnO2 which is liable for efficient electron donation from the Mn3+ to adsorbed oxygen in the rate determining step. RDE results showed that MnO2/CNT follows 4e− transfer pathway, indicating its ability to act as an effective ORR electrocatalyst

Enhanced biohydrogen production from citrus wastewater using anaerobic sludge pretreated by an electroporation technique

In the present study, the applicability of electroporation (EP) has been investigated as a pretreatment method for enriching hydrogen producers and eliminating hydrogen consumers in anaerobic sludge (AS). Citrus wastewater was used as a feed source for biohydrogen production. Different treatment intensities (TI) of EP for 0.5 min (TI = 30 kWh/m3), 1 min (TI = 60 kWh/m3), and 2 min (TI = 120 kWh/m3) were employed to observe the effects of EP on the microbial community of AS. Furthermore, sonication with a probe, sonication in a bath, and heat-shock pretreatments were also conducted to compare the hydrogen yield with EP. The cell inactivation was evaluated and visualized using colony-forming units (CFU) and field emission scanning electron microscopy (FESEM), respectively. Among the different TIs, the TI of 60 kWh/m3 achieved higher methanogen inactivation with maximum hydrogen (896 mL) production compared to other EP pretreatments after 180 h of dark fermentation. In comparison with other pretreatments, the highest hydrogen production of 896 mL was achieved with EP treatment, followed by sonication with a probe (678 mL) and sonication in a bath (563 mL). The heat-shock pretreatment exhibited the lowest ultimate hydrogen production of 545 mL among the four different methods applied in this study. The outcome of this study suggests that EP is a promising technique for pretreating mixed cultures for the enhanced production of biohydrogen

Real-time flow simulation of indoor environments using lattice Boltzmann method

A novel lattice Boltzmann method (LBM) based 3D computational fluid dynamics (CFD) technique has been implemented on the graphics processing unit (GPU) for the purpose of simulating the indoor environment in real-time. We study the time evolution of the turbulent airflow and temperature inside a test chamber and in a simple model of a four-bed hospital room. The predicted results from LBM are compared with traditional CFD based large eddy simulations (LES). Reasonable agreement between LBM results and LES method is observed with significantly faster computational times

Performance of Klebsiella oxytoca to Generate Electricity from POME in Microbial Fuel Cell

This study is aimed to evaluate the electricity generation from microbial fuel cell (MFC) and to analyze the microbial community structure of city wastewater and anaerobic sludge to enhance the MFC performance. MFCs, enriched with palm oil mill effluent (POME) were employed to harvest electricity by innoculating of Klebsiella oxytoca, collected from city wastewater and other microbes from anaerobic sludge (AS). The MFC showed maximum power density of 207.28 mW/m3 with continuous feeding of POME using microbes from AS. Subsequent replacement with Klebsiella oxytoca resulted maximum power density of 1236 mW/m3 by utilizing complex substrate POME which was six times higher as compared to MFC operated with AS. Based on Biolog gene III analysis, relatively higher abundance of Klebsiella oxytoca was detected in the city wastewater. Predominant microorganisms such as Gammaproteobacteria, Azospiraoryzae, Acetobacterperoxydans and Solimonasvariicoloris were isolated from palm oil anaerobic sludge as well as from biofilm of MFC. Enriched electrochemically active bacteria Klebsiella oxytoca showed better performance to generate electricity from complex POME substrates compare to AS. These results demonstrate that the power output of MFCs can be increased significantly using Klebsiella oxytoca

Bioremediation of Palm Oil Mill Effluent and Lipid Production by Lipomyces Starkeyi: A Combined Approach

The discharge of palm oil mill effluent (POME) on arable land causes large amounts of environmental distress due to its high concentration of phenolic compounds and chemical oxygen demand (COD). The approach of simultaneous microbial oil production and wastewater treatment is an attractive option to combine renewable energy production and environmental resilience. This study aims to produce cost effective microbial lipids using the oleaginous yeast Lipomyces starkeyi through the bioremediation of POME. A moderately dilute solution (50%) of POME showed higher microbial growth and lipid accumulation and offered a significantly higher degree of bioremediation. A lipid content of 21.32% was achieved with 50% POME, whereas the value was 15.14% for 25% POME. Three different techniques including ultrasonic treatment, Fenton's reagent and Fenton's + ultrasonic were employed to extract lipids from microbial biomass, and the maximum lipid concentration was obtained using the Fenton's + ultrasonic treatment. The degree of bioremediation was evaluated by the calculating seed germination index (GI) values. Higher GI values were observed for the 25% and 50% dilutions compared to undiluted (100%) POME. This combined approach can be a potential alternative technology that integrates bioremediation of POME with microbial lipid production

Prolonged Stability of Air-Cathode Microbial Fuel Cell Performance by Inhibiting Aerobic Microbial Growth Using Platinum and Carbon Nanotube (PT-CNT) Nanoparticles as a Cathode Catalyst

The inescapable growth of heterotrophic aerobic bacteria on the surface of air cathodes is an important factor causing oxygen depletion and substrate loss thus reduce the performance stability of air cathode single-chamber microbial fuel cells (MFCs). In this study, the possible use of platinum and carbon nanotube (Pt-CNT) nanoparticles as an antimicrobial agents as well as cathode catalyst for air-cathode MFCs was examined. The biomass content on carbon air-cathodes (CACs) was substantially decreased by 38.2% with Pt-CNT treatment after 26 days of MFCs operation. As a result, the oxygen reduction catalytic performance of the Pt-CNT treated CACs was much stable whereas the fast performance decline of the untreated cathode. Consequently, a quite stable electricity production was obtained for the MFCs with the Pt-CNT treated CACs, alternatively with a 22.5% decrease in maximum power density of the MFCs observed with the untreated cathode. Based on these results, it can be concluded that (1) the growth of oxygenconsuming heterotrophic microbes could be inhibited by Pt-CNT, (2) Pt-CNT could be applied as a cathode catalyst for oxygen reduction, thus (4) the MFC with the Pt-CNT -coated cathode led to the enhenced stable current generation

Evaluation of Electricity Generation and Wastewater Treatment from Palm Oil Mill Effluent Using Single and Dual Chamber Microbial Fuel Cell

Microbial Fuel Cells (MFCs) can be simultaneously used for the treatment of wastewater and generation of electricity. In this study, single chamber air-cathode MFC (sMFC) and double chambered MFC (dMFC) were compared for the palm oil mill effluent (POME) treatment and generation of electricity while Pseudomonas aeruginosa (ATCC – 27,853) was used as inoculum and POME used as substrate. The dMFC was efficient and found to be producing maximum power density of 4.2 W/m3 whereas sMFC produced a maximum power density 1.7 W/m3. Moreover, the dMFC showed higher COD (54%) removal when compared with sMFC (41%). The significant power generation and COD removal efficiency observed in dMFC might be attributed to the microbial catalyzed and reversible electrochemical reactions occurring in the anodic chamber and cathode chamber of dMFC. These results suggest that dMFC is efficient than sMFC in producing electricity as well as in treating wastewater