372 research outputs found
Design and optimization of joint iterative detection and decoding receiver for uplink polar coded SCMA system
SCMA and polar coding are possible candidates for 5G systems. In this paper, we firstly propose the joint iterative detection and decoding (JIDD) receiver for the uplink polar coded sparse code multiple access (PC-SCMA) system. Then, the EXIT chart is used to investigate the performance of the JIDD receiver. Additionally, we optimize the system design and polar code construction based on the EXIT chart analysis. The proposed receiver integrates the factor graph of SCMA detector and polar soft-output decoder into a joint factor graph, which enables the exchange of messages between SCMA detector and polar decoder iteratively. Simulation results demonstrate that the JIDD receiver has better BER performance and lower complexity than the separate scheme. Specifically, when polar code length N=256 and code rate R=1/2 , JIDD outperforms the separate scheme 4.8 and 6 dB over AWGN channel and Rayleigh fading channel, respectively. It also shows that, under 150% system loading, the JIDD receiver only has 0.3 dB performance loss compared to the single user uplink PC-SCMA over AWGN channel and 0.6 dB performance loss over Rayleigh fading channel
Surface charging on HVDC spacers considering time-varying effect of temperature and electric fields
The dynamic behavior of surface charging on spacers in DC-GILs can be influenced by multi-factors including the non-uniform distributed electric field as well as the time-varying temperature gradient. In this paper, the time-varying effect of surface charging phenomenon on spacers is studied and a time-varying mathematical model is established, based on the influence of temperature and electric field on the ion mobility at the gas phase and the bulk conductivity in the solid phase. The results verify that the bulk conductivity can be greatly influenced by temperature, which leads to an increase in the surface charge density on the spacer. This allows the surface charge accumulation to stabilize more quickly. However, the ion mobility from the gas phase is less affected by temperature. When the non-uniform distributed electric field changes from 1.3 to 6.4 kV/mm, ion mobility is less influenced and the surface charge density on the spacer varies slightly. In this case, the effects of the non-uniformly distributed electric field in surface charge density variation is much smaller and can be ignored
Validation of S-NPP VIIRS Day-Night Band and M Bands Performance Using Ground Reference Targets of Libya 4 and Dome C
This paper provides methodologies developed and implemented by the NASA VIIRS Calibration Support Team (VCST) to validate the S-NPP VIIRS Day-Night band (DNB) and M bands calibration performance. The Sensor Data Records produced by the Interface Data Processing Segment (IDPS) and NASA Land Product Evaluation and Algorithm Testing Element (PEATE) are acquired nearly nadir overpass for Libya 4 desert and Dome C snow surfaces. In the past 3.5 years, the modulated relative spectral responses (RSR) change with time and lead to 3.8% increase on the DNB sensed solar irradiance and 0.1% or less increases on the M4-M7 bands. After excluding data before April 5th, 2013, IDPS DNB radiance and reflectance data are consistent with Land PEATE data with 0.6% or less difference for Libya 4 site and 2% or less difference for Dome C site. These difference are caused by inconsistent LUTs and algorithms used in calibration. In Libya 4 site, the SCIAMACHY spectral and modulated RSR derived top of atmosphere (TOA) reflectance are compared with Land PEATE TOA reflectance and they indicate a decrease of 1.2% and 1.3%, respectively. The radiance of Land PEATE DNB are compared with the simulated radiance from aggregated M bands (M4, M5, and M7). These data trends match well with 2% or less difference for Libya 4 site and 4% or less difference for Dome C. This study demonstrate the consistent quality of DNB and M bands calibration for Land PEATE products during operational period and for IDPS products after April 5th, 2013
Initial On-Orbit Radiometric Calibration of the Suomi NPP VIIRS Reflective Solar Bands
The on-orbit radiometric response calibration of the VISible/Near InfraRed (VISNIR) and the Short-Wave InfraRed (SWIR) bands of the Visible/Infrared Imager/Radiometer Suite (VIIRS) aboard the Suomi National Polar-orbiting Partnership (NPP) satellite is carried out through a Solar Diffuser (SD). The transmittance of the SD screen and the SD's Bidirectional Reflectance Distribution Function (BRDF) are measured before launch and tabulated, allowing the VIIRS sensor aperture spectral radiance to be accurately determined. The radiometric response of a detector is described by a quadratic polynomial of the detector?s digital number (dn). The coefficients were determined before launch. Once on orbit, the coefficients are assumed to change by a common factor: the F-factor. The radiance scattered from the SD allows the determination of the F-factor. In this Proceeding, we describe the methodology and the associated algorithms in the determination of the F-factors and discuss the results
Effect of long‐term fluorination on surface electrical performance of ethylene propylene rubber
n/
Effect of thermal ageing on space charge in ethylene propylene rubber at DC voltage
To understand the space charge characteristics of ethylene propylene rubber (EPR) used in MV/HV power cables under thermal stress, the space charge profile is measured by the pulsed electro-acoustic method under 20 kV/mm at 120 and 160 \ub0C. The complex permittivity and physicochemical properties at the different ageing stages are measured and analyzed for an understanding of the effects of thermal ageing on space charge characteristics. The trap properties of EPR during thermal ageing is calculated and analyzed based on the space charge decay model. The results show that both the ageing time and temperature can affect the space charge characteristics of EPR The space charge characteristics of EPR can be ascribed to the trapping sites caused by the complex chemical and physical structures during thermal ageing. Under the thermal oxygen process, the polar groups and ions increase because of the EPR molecular chain breakages, and the charge injection from the electrodes increases. Based on the decay model of space charge and isothermal decay current theory, the distribution of trap levels in EPR at different ageing stages is obtained. The trap distribution under different ageing process can be explained by the theory of trap filling
Ecofriendly electrospun membranes loaded with visible-light-responding nanoparticles for multifunctional usages : highly efficient air filtration, dye scavenging, and bactericidal activity
Ambient particulate matter pollution has posed serious threats to global environment and public health. However, highly efficient filtration of submicron particles, the so-named "secondary pollution" caused by, e.g., bacterial growth in filters and the use of nondegradable filter materials, remains a serious challenge. In this study, poly(vinyl alcohol) (PVA) and konjac glucomannan (KGM)-based nanofiber membranes, loaded with ZnO nanoparticles, were prepared through green electrospinning and ecofriendly thermal cross-linking. Thus obtained fibrous membranes not only show highly efficient air-filtration performance but also show superior photocatalytic activity and antibacterial activity. The filtration efficiency of the ZnO@PVA/KGM membranes for ultrafine-particles (300 nm) was higher than 99.99%, being superior to that of commercial HEPA filters. By virtue of the high photocatalytic activity, methyl orange was efficiently decolorized with a removal efficiency of more than 98% at an initial concentration of 20 mg under 120 min of solar irradiation. A multifunctional membrane with high removal efficiency, low flow resistance, superior photocatalytic activity, and superior antibacterial activity was successfully achieved. It is conceivable that the combination of a biodegradable polymer and an active metal particle would form an unprecedented photocatalytic system, which will be quite promising for environmental remediation such as air filtration and water treatment
Improvements of VIIRS and MODIS Solar Diffuser and Lunar Calibration
Both VIIRS and MODIS instruments use solar diffuser (SD) and lunar observations to calibrate their reflective solar bands (RSB). A solar diffuser stability monitor (SDSM) is used to track the SD on-orbit degradation. On-orbit observations have shown similar wavelength-dependent SD degradation (larger at shorter VIS wavelengths) and SDSM detector response degradation (larger at longer NIR wavelengths) for both VIIRS and MODIS instruments. In general, the MODIS scan mirror has experienced more degradation in the VIS spectral region whereas the VIIRS rotating telescope assembly (RTA) mirrors have seen more degradation in the NIR and SWIR spectral region. Because of this wavelength dependent mirror degradation, the sensor's relative spectral response (RSR) needs to be modulated. Due to differences between the solar and lunar spectral irradiance, the modulated RSR could have different effects on the SD and lunar calibration. In this paper, we identify various factors that should be considered for the improvements of VIIRS and MODIS solar and lunar calibration and examine their potential impact. Specifically, we will characterize and assess the calibration impact due to SD and SDSM attenuation screen transmission (uncertainty), SD BRF uncertainty and onorbit degradation, SDSM detector response degradation, and modulated RSR resulting from the sensor's optics degradation. Also illustrated and discussed in this paper are the calibration strategies implemented in the VIIRS and MODIS SD and lunar calibrations and efforts that could be made for future improvements
- …