Evaluation of a pneumatic boot deicing system on a general aviation wing model

The aerodynamic characteristics of a typical modern general aviation airfoil were investigated with and without a pneumatic boot ice protection system. The ice protection effectiveness of the boot was studied. This includes the change in drag on the airfoil with the boot inflated and deflated, the change in drag due to primary and residual ice formation, drag change due to cumulative residual ice formation, and parameters affecting boot effectiveness. Boot performance was not affected by tunnel total temperature or velocity. Marginal effect in performance was associated with angle of attack. Significant effects on performance were caused by variations in droplet size, LWC, ice cap thickness inflation pressure, and surface treatment

Icing tunnel tests of a glycol-exuding porous leading edge ice protection system on a general aviation airfoil

A glycol-exuding porous leading edge ice protection system was tested. Results show that the system is very effective in preventing ice accretion (anti-ice mode) or removing ice from an airfoil. Minimum glycol flow rates required for anti-icing are a function of velocity, liquid water content in the air, ambient temperature, and droplet size. Large ice caps were removed in only a few minutes using anti-ice flow rates. It was found that the shed time is a function of the type of ice, size of the ice cap, angle of attack, and glycol flow rate. Wake survey measurements show that there is no significant drag penalty for the installation or operation of the system tested

Signatures of electron-boson coupling in half-metallic ferromagnet Mn5_5Ge3_3: study of electron self-energy Σ(ω)\Sigma(\omega) obtained from infrared spectroscopy

We report results of our infrared and optical spectroscopy study of a half-metallic ferromagnet Mn$_5$Ge$_3$. This compound is currently being investigated as a potential injector of spin polarized currents into germanium. Infrared measurements have been performed over a broad frequency (50 - 50000 cm$^{-1}$) and temperature (10 - 300 K) range. From the complex optical conductivity $\sigma(\omega)$ we extract the electron self-energy $\Sigma(\omega)$. The calculation of $\Sigma(\omega)$ is based on novel numerical algorithms for solution of systems of non-linear equations. The obtained self-energy provides a new insight into electron correlations in Mn$_5$Ge$_3$. In particular, it reveals that charge carriers may be coupled to bosonic modes, possibly of magnetic origin

Burst Testing of Triaxial Braided Composite Tubes

Applications using triaxial braided composites are limited by the materials transverse strength which is determined by the delamination capacity of unconstrained, free-edge tows. However, structural applications such as cylindrical tubes can be designed to minimize free edge effects and thus the strength with and without edge stresses is relevant to the design process. The transverse strength of triaxial braided composites without edge effects was determined by internally pressurizing tubes. In the absence of edge effects, the axial and transverse strength were comparable. In addition, notched specimens, which minimize the effect of unconstrained tow ends, were tested in a variety of geometries. Although the commonly tested notch geometries exhibited similar axial and transverse net section failure strength, significant dependence on notch configuration was observed. In the absence of unconstrained tows, failure ensues as a result of bias tow rotation, splitting, and fracture at cross-over regions

Localized and Delocalized Charge Transport in Single-Wall Carbon-Nanotube Mats

We measured the complex dielectric constant in mats of single-wall carbon-nanotubes between 2.7 K and 300 K up to 0.5 THz. The data are well understood in a Drude approach with a negligible temperature dependence of the plasma frequency (omega_p) and scattering time (tau) with an additional contribution of localized charges. The dielectric properties resemble those of the best ''metallic'' polypyrroles and polyanilines. The absence of metallic islands makes the mats a relevant piece in the puzzle of the interpretation of tau and omega_p in these polymers.Comment: 4 pages including 4 figure

Approaches for Tensile Testing of Braided Composites

For angleply composites, lamina tension and compression strengths are commonly determined by applying classical lamination theory to test data obtained from testing of angleply composite specimens. For textile composites such as 2D triaxial braids, analysis is more complex and standard test methods do not always yield reliable strength measurements. This paper describes recent research focused on development of more reliable tensile test methods for braided composites and presents preliminary data for various approaches. The materials investigated in this work have 0deg+/-60 2D triaxial braid architecture with nearly equal fiber volume fraction in each of the three fiber directions. Flat composite panels are fabricated by resin transfer molding (RTM) using six layers of the braided preform aligned along the 0deg fiber direction. Various epoxy resins are used as matrix materials. Single layer panels are also fabricated in order to examine local variations in deformation related to the braid architecture. Specimens are cut from these panels in the shape of standard straight-sided coupons, an alternative bowtie geometry, and an alternative notched geometry. Axial tensile properties are measured using specimens loaded along the 0deg fiber direction. Transverse tensile properties are measured using specimens loaded perpendicular to the 0deg fibers. Composite tubes are also fabricated by RTM. These tubes are tested by internal pressurization using a soft rubbery material sealed between the inside diameter of the tube and the load fixtures. The ends of the tube are unconstrained, so the primary load is in the hoop direction. Tubes are fabricated with the 0deg fibers aligned along the tube axis by overbraiding the preform on a mandrel. Since the loading is in the hoop direction, testing of the overbraided tube provides a measure of transverse tensile strength. Previous work has indicated that straight-sided coupons yield a transverse tensile strength that is much lower than the expected material strength because of premature edge-initiated failure. Full-field strain measured during transverse tensile tests clearly showed accumulation of edge damage prior to failure. In the current work, high speed video and testing of single layer specimens are used to investigate potential failure mechanisms in more detail. High speed video clearly shows the edge initiation in six layer transverse tensile test coupons. Specimens with the bowtie geometry and the notched geometry minimize this edge effect and yield significantly higher transverse tensile strength values compared to the straight-sided coupons. However, bowtie and notched specimens geometries are not ideal because of the non-uniform stress and strain fields in the region of failure. Testing of tubes using internal pressurization eliminates edge-initiated failure and provides a more uniform state of stress and strain. Preliminary results indicate that bowtie, notched, and tube specimens yield comparable values for transverse tensile strength and that these values are much higher than the strength measured using a straight-sided coupon

Dopant-induced crossover from 1D to 3D charge transport in conjugated polymers

The interplay between inter- and intra-chain charge transport in bulk polythiophene in the hopping regime has been clarified by studying the conductivity as a function of frequency (up to 3 THz), temperature and doping level. We present a model which quantitatively explains the observed crossover from quasi-one-dimensional transport to three-dimensional hopping conduction with increasing doping level. At high frequencies the conductivity is dominated by charge transport on one-dimensional conducting chains.Comment: 4 pages, 2 figure

Strong localization of electrons in quasi-one-dimensional conductors

We report on the experimental study of electron transport in sub-micron-wide ''wires'' fabricated from Si $\delta$-doped GaAs. These quasi-one-dimensional (Q1D) conductors demonstrate the crossover from weak to strong localization with decreasing the temperature. On the insulating side of the crossover, the resistance has been measured as a function of temperature, magnetic field, and applied voltage for different values of the electron concentration, which was varied by applying the gate voltage. The activation temperature dependence of the resistance has been observed with the activation energy close to the mean energy spacing of electron states within the localization domain. The study of non-linearity of the current-voltage characteristics provides information on the distance between the critical hops which govern the resistance of Q1D conductors in the strong localization (SL) regime. We observe the exponentially strong negative magnetoresistance; this orbital magnetoresistance is due to the universal magnetic-field dependence of the localization length in Q1D conductors. The method of measuring of the single-particle density of states (DoS) in the SL regime has been suggested. Our data indicate that there is a minimum of DoS at the Fermi level due to the long-range Coulomb interaction.Comment: 12 pages, 11 figures; the final version to appear in Phys. Rev.

Genomic profiling using array comparative genomic hybridization define distinct subtypes of diffuse large b-cell lymphoma: a review of the literature

Diffuse large B-cell lymphoma (DLBCL) is the most common type of non-Hodgkin Lymphoma comprising of greater than 30% of adult non-Hodgkin Lymphomas. DLBCL represents a diverse set of lymphomas, defined as diffuse proliferation of large B lymphoid cells. Numerous cytogenetic studies including karyotypes and fluorescent in situ hybridization (FISH), as well as morphological, biological, clinical, microarray and sequencing technologies have attempted to categorize DLBCL into morphological variants, molecular and immunophenotypic subgroups, as well as distinct disease entities. Despite such efforts, most lymphoma remains undistinguishable and falls into DLBCL, not otherwise specified (DLBCL-NOS). The advent of microarray-based studies (chromosome, RNA, gene expression, etc) has provided a plethora of high-resolution data that could potentially facilitate the finer classification of DLBCL. This review covers the microarray data currently published for DLBCL. We will focus on these types of data; 1) array based CGH; 2) classical CGH; and 3) gene expression profiling studies. The aims of this review were three-fold: (1) to catalog chromosome loci that are present in at least 20% or more of distinct DLBCL subtypes; a detailed list of gains and losses for different subtypes was generated in a table form to illustrate specific chromosome loci affected in selected subtypes; (2) to determine common and distinct copy number alterations among the different subtypes and based on this information, characteristic and similar chromosome loci for the different subtypes were depicted in two separate chromosome ideograms; and, (3) to list re-classified subtypes and those that remained indistinguishable after review of the microarray data. To the best of our knowledge, this is the first effort to compile and review available literatures on microarray analysis data and their practical utility in classifying DLBCL subtypes. Although conventional cytogenetic methods such as Karyotypes and FISH have played a major role in classification schemes of lymphomas, better classification models are clearly needed to further understanding the biology, disease outcome and therapeutic management of DLBCL. In summary, microarray data reviewed here can provide better subtype specific classifications models for DLBCL

A notched coupon approach for tensile testing of braided composites

A notched coupon geometry was evaluated as a method for tensile testing of 2D triaxial braid composites. Edge initiated shear failure has been observed in transverse tension tests using straight-sided coupons based on ASTM D3039. The notched coupon was designed to reduce the effects of edge initiated failure and produce the desired tensile failure. A limited set of tests were performed with partial pressurization of tubes to determine the transverse tensile strength in the absence of edge initiated failure. The transverse strength measured with the notched coupons was considerably higher than the straight-sided coupons, comparable to the tube results, and closer to the maximum possible strength based on maximum fiber strain. Further investigations of the effects of the observed biaxial stress state and stress concentrations in the notched geometry are needed