Au/Zn Contacts to rho-InP: Electrical and Metallurgical Characteristics and the Relationship Between Them

The metallurgical and electrical behavior of Au/Zn contacting metallization on p-type InP was investigated as a function of the Zn content in the metallization. It was found that ohmic behavior can be achieved with Zn concentrations as small as 0.05 atomic percent Zn. For Zn concentrations between 0.1 and 36 at. percent, the contact resistivity rho(sub c) was found to be independent of the Zn content. For low Zn concentrations the realization of ohmic behavior was found to require the growth of the compound Au2P3 at the metal-InP interface. The magnitude of rho(sub c) is shown to be very sensitive to the growth rate of the interfacial Au2P3 layer. The possibility of exploiting this sensitivity to provide low resistance contacts while avoiding the semiconductor structural damage that is normally attendant to contact formation is discussed

Tribology and Microstructure of PS212 with a Cr2O3 Seal Coat

PS212 is a plasma sprayed metal bonding chrome carbide coating with solid lubricant additives which has lubricating properties at temperatures up to about 900 deg C. The coating is diamond ground to achieve an acceptable tribological surface. But, as with many plasma spray coatings, PS212 is not fully-dense. In this study, a chromium oxide base seal coating is used in an attempt to seal any porosity that is open to the surface of the PS212 coating, and to study the effect of the sealant on the tribological properties of PS212. The results indicate that the seal coating reduces friction and wear when it is applied and then diamond ground leaving a thin layer of seal coating which fills in the surface pits of the PS212 coating

Oxygen Plasma Treatment and Deposition of CNx on a Fluorinated Polymer Matrix Composite for Improved Erosion Resistance

The use of polymer matrix composites in aerospace propulsion applications is currently limited by insufficient resistance to erosion by abrasive media. Erosion resistant coatings may provide necessary protection; however, adhesion to many high temperature polymer matrix composite (PMC) materials is poor. A low pressure oxygen plasma treatment process was developed to improve adhesion of CNx coatings to a carbon reinforced, fluorinated polymer matrix composite. Fullerene-like CNx was selected as an erosion resistant coating for its high hardness-to-elastic modulus ratio and elastic resilience which were expected to reduce erosion from media incident at different angles (normal or glancing) relative to the surface. In situ x-ray photoelectron spectroscopy was used to evaluate the effect of the plasma treatment on surface chemistry, and electron microscopy was used to identify changes in the surface morphology of the PMC substrate after plasma exposure. The fluorine concentration at the surface was significantly reduced and the carbon fibers were exposed after plasma treatment. CNx coatings were then deposited on oxygen treated PMC substrates. Qualitative tests demonstrated that plasma treatment improved coating adhesion resulting in an erosion resistance improvement of a factor of 2 compared to untreated coated composite substrates. The combination of PMC pretreatment and coating with CNx reduced the erosion rate by an order of magnitude for normally incident particles

Physical and Tribological Characteristics of Ion-Implanted Diamond Films

Unidirectional sliding friction experiments were conducted with a natural, polished diamond pin in contact with both as-deposited and carbon-ion-implanted diamond films in ultrahigh vacuum. Diamond films were deposited on silicon, silicon carbide, and silicon nitride by microwave-plasma-assisted chemical vapor deposition. The as-deposited diamond films were impacted with carbon ions at an accelerating energy of 60 keV and a current density of 50 micron A/cm(exp 2) for approximately 6 min, resulting in a dose of 1.2 x 10(exp 17) carbon ions/cm(exp 2). The results indicate that the carbon ion implantation produced a thin surface layer of amorphous, nondiamond carbon. The nondiamond carbon greatly decreased both friction and wear of the diamond films. The coefficients of friction for the carbon-ion-implanted, fine-grain diamond films were less than 0.1, factors of 20 to 30 lower than those for the as-deposited, fine-grain diamond films. The coefficients of friction for the carbon-ion-implanted, coarse-grain diamond films were approximately 0.35, a factor of five lower than those for the as-deposited, coarse-grain diamond films. The wear rates for the carbon-ion-implanted, diamond films were on the order of 10(exp -6) mm(exp 3)/Nm, factors of 30 to 80 lower than that for the as-deposited diamond films, regardless of grain size. The friction of the carbon-ion-implanted diamond films was greatly reduced because the amorphous, nondiamond carbon, which had a low shear strength, was restricted to the surface layers (less than 0.1 micron thick) and because the underlying diamond materials retained their high hardness. In conclusion, the carbon-ion-implanted, fine-grain diamond films can be used effectively as wear resistant, self-lubricating coatings for ceramics, such as silicon nitride and silicon carbide, in ultrahigh vacuum

Fretting wear behavior of duplex PEO/chameleon coating on Al alloy

Plasma electrolytic oxidation (PEO) is an attractive technology for improving resistance to wear, heat and corrosion of aluminum alloys. PEO results in a hard, well-adhered alumina ceramic coating with a morphology which is graded from a dense region near the substrate interface to a porous outer region. Such properties mean that PEO can be an ideal underlying layer for the application of solid lubricants which can be entrapped in outer pores and provide reservoirs for the tribological contact lubrication. This study investigates the fretting wear behavior and adaptive mechanisms for a PEO-produced alumina surface of about 11–12 GPa hardness with a top layer of an MoS2/Sb2O3/C chameleon solid lubricating coating, the composition of which was designed to self-adapt in variable humidity environments for friction and wear reduction. Coupons of AA 6082 alloy were coated by the PEO process and then were over-coated by a burnishing process with a MoS2/Sb2O3/C chameleon coating to prepare a duplex coating combination. The coated surfaces were investigated using nanoindenation, Raman spectroscopy and scanning electroscopy and were then subjected to fretting wear tests against steel and alumina balls with variable amplitude (0–100 μm) and loads (10–100 N) in both humid air and in dry nitrogen environment conditions. The tests demonstrated low friction coefficients, considerable reduction in critical amplitude for the stick-slip transition, and self-adaptive tribological behavior in cycled environment tests. Friction coefficients of the order of 0.10–0.15 in humid air and 0.06–0.09 in dry nitrogen were recorded and linked with the surface self-adjustment from graphite to MoS2 lubrication, respectively, which was confirmed by Raman spectroscopy. The studies demonstrate the effectiveness of the PEO/chameleon duplex coating system for the friction reduction of and fretting wear in the gross-slip regime, as well as significantly reducing the critical amplitude of stick-slip transition for fatigue wear mitigation

Dust Climatology of the NASA Dryden Flight Research Center (DFRC) in Lancaster, California, USA

Abstract: A 15-year (1997–2011) climatology of dust events at the NASA DFRC in Lancaster, California, USA, was performed to evaluate how the extratropical systems were associated with dust storms over this region. For this study, we collected meteorological data for Edwards Air Force Base (EAFB) in Lancaster, California, which is very close to NASA DFRC, from wunderground.com, National Centers for Environmental Prediction (NCEP)/North American Regional Reanalysis (NARR), NCEP/Hydro-meteorological Prediction Center/National Weather Service (NWS), and Unisys analyses. We find that the dust events were associated with the development of a deep convective boundary layer, turbulence kinetic energy (TKE) ≥3 J/kg, a deep unstable lapse rate layer, a wind speed above the frictional threshold wind speed necessary to ablate dust from the surface (≥7.3 m/s), a presence of a cold trough above the deep planetary boundary layer (PBL), a strong cyclonic jet, an influx of vertical sensible heat from the surrounding area, and a low volumetric soil moisture fraction <0.3. The annual mean number of dust events, their mean duration, and the unit duration per number of event for each visibility range, when binned as <11.2 km, <8 km, <4.8 km, <1.6 km, and <1 km were calculated. The visibility range values were positively correlated with the annual mean number of dust events, duration of dust events, and the ratio of duration of dust events. The percentage of the dust events by season shows that most of the dust events occurred in autumn (44.7%), followed by spring (38.3%), and equally in summer and winter with these seasons each accounting for 8.5% of events. This study also shows that the summer had the highest percentage (10%) of the lowest visibility condition (<1 km) followed by autumn (2%). Neither of the other two seasons—winter and spring—experienced such a low visibility condition during the entire dust events over 15 years. Winter had the highest visibility (<11.2 km) percentage, which was 67% followed by spring (55%). Wind speed increasing to a value within the range of 3.6–11 m/s was typically associated with the dust events