A Self-Sustainable and Micro-Second Time Synchronized Multi-Node Wireless System for Aerodynamic Monitoring on Wind Turbines

Wind energy generation plays a vital role in transitioning from fossil fuel-based energy sources and in alleviating the impacts of global warming. However, global wind energy coverage still needs to rise, while requiring a significant step up in conversion efficiency: monitoring wind flow and operational parameters of wind turbines is an essential prerequisite for coverage and conversion efficiency optimization. This paper presents a low-power, self-sustainable, and time-synchronised system for aerodynamic and acoustic measurements on operating wind turbines. It includes 40 high-accuracy barometers, 10 microphones, 5 differential pressure sensors, and implements a coarse time synchronisation on top of a Bluetooth Low Energy 5.1 protocol tuned for long-range communications. Moreover, we field-assessed the node capability to collect precise and accurate aerodynamic data with a multi-node setup. Outdoor experimental tests revealed that the system can acquire heterogeneous data with a time synchronisation error below 100 mu s and sustain a data rate of 600 kbps over 400 m with up to 5 sensor nodes, enough to fully instrument a wind turbine. The proposed method does not add any traffic overhead on the Bluetooth Low Energy 5.1 protocol, fully relying only on connection events and withstands transmission discontinuity often present in long range wireless communications

Performance enhancement of downwind sails due to leading edge flapping: A wind tunnel investigation

This work presents a wind tunnel experimental study on the effect of the leading edge flapping on the aerodynamic performance of a spinnaker. Four J80-class spinnaker models, combining two different assembling structures (panel layout) and two different sail materials are tested at various wind speeds and wind angles in a wind tunnel. Results show that, for the wind angle range the spinnaker is designed for, the sustained periodic flapping of the sail leading edge has a significant benefit on performance, with 10% increase in drive force. In these model-scale tests, the sail structural properties did not show significant differences in performance, but affect the point where flapping sets in: a model with a stiffer material and a cross-cut panel layout starts flapping for a longer sheet length, compared to a lighter cloth and a tri-radial layout. Finally, it is shown that the nondimensional flapping frequency is rather constant 0.4 in the design range of wind angle, but it varies with the wind speed and sail structural properties on a smaller wind angle where the spinnaker is more stretched.FP7 PEOPLE IRSES and COFUN

Numerical study of a flexible sail plan : effect of pitching decomposition and adjustments

A numerical investigation of the dynamic Fluid Structure Interaction (FSI) of a yacht sail plan submitted to harmonic pitching is presented to analyse the effects of motion simplifications and rigging adjustments on aerodynamic forces. It is shown that the dynamic behaviour of a sail plan subject to yacht motion clearly deviates from the quasi-steady theory. The aerodynamic forces presented as a function of the instantaneous apparent wind angle show hysteresis loops. These hysteresis phenomena do not result from a simple phase shift between forces and motion. Plotting the hysteresis loops in the appropriate coordinate system enables the associated energy to be determined. This amount of exchanged energy is shown to increase almost linearly with the pitching reduced frequency and to increase almost quadratically with the pitching amplitude in the investigated ranges. The effect of reducing the real pitching motion to a simpler surge motion is investigated. Results show significant discrepancies on the aerodynamic forces amplitude and the hysteresis phenomenon between pitching and surge motion. However, the superposition assumption consisting in a decomposition of the surge into two translations normal and collinear to the apparent wind is verified. Then, simulations with different dock tunes and backstay loads highlight the importance of rig adjustments on the aerodynamic forces and the dynamic behaviour of a sail plan

Dynamic measurements of pressures, sail shape and forces on a full-scale spinnaker

This work presents a full-scale experimental study on a sailing yacht in downwind conditions with simultaneous time-resolved measurements of pressures, sail shape and loads. Those on-water experiments on a J/80 class yacht permit the dynamic behaviour of the fluid structure system made of a light cloth sail and highly curved flow to be investigated. Aerodynamic forces on the asymmetric spinnaker were determined from pressure distribution and shape measurements and also from strain gauges located on the corners of the sail. Both time-averaged and instantaneous data are analysed. The time-averaged pressures and forces were studied according to the apparent wind angle. The pressure distribution and thus the loads tend to decrease when the apparent wind angle is increased. The standard deviation of pressures was largest near the luff, decreasing downstream. Simultaneous time series recordings of the pressure distributions, flapping sail shapes, and forces in the sheets show a strong correlation. Flapping of spinnaker creates pressure peaks at the leading edge, increasing the aerodynamic forces dynamically by 50 to 70%. These results will also give reliable benchmark data to validate unsteady fluid structure interaction predictions from numerical simulations of downwind sails

Experimental studies of fluid-structure interaction on downwind sails

Cette thèse présente une étude expérimentale sur un voilier instrumenté, menée pour décrire le comportement aéro-élastique des voiles et du gréement pour des navigations au portant. Les formes des voiles utilisées sont des surfaces non développables avec de fortes courbures provoquant une séparation massive de l’écoulement. De plus, les spinnakers sont des voiles fines et souples rendant l’interaction fluide-structure fortement couplée. A cause du non-respect de certaines règles de similitude, le comportement dynamique d’un spinnaker se prête mal à l’étude en soufflerie et nécessite une comparaison avec des mesures in-situ. Les simulations numériques instationnaires modélisant le comportement aéro-élastique des voiles et du gréement doivent être qualifiées et demandent également des validations. C’est pourquoi un système d’instrumentation embarquée est mis en place sur un J/80, un voilier de huit mètres de long. Il s’agit de mesurer dynamiquement la forme en navigation du spinnaker, les efforts dans les gréements dormant et courant, la répartition de pression sur la voile ainsi que le vent et les attitudes du bateau. La forme du spinnaker en navigation est obtenue grâce à un système de mesure photogrammétrique développé pendant la thèse. La précision de ce système, meilleure que 1,5%, permet de mesurer la forme générale de la voile ainsi que les déformations importantes telles que celles liées au faseyement du guindant. L’effort aérodynamique produit par le spinnaker est obtenu grâce à la mesure de l’intensité des efforts et de leurs directions aux trois extrémités (drisse, amure, écoute) ainsi que par la mesure des pressions sur la voile. Le comportement général du spinnaker est analysé en fonction de l’angle du vent apparent. Une nouvelle représentation utilisant les surfaces de Bézier triangulaires est développée pour décrire la forme tridimensionnelle du spinnaker. Quelques points de contrôles suffisent pour représenter la voile et caractériser le type de voile. Un comportement dynamique propre au spinnaker est également étudié. Le réglage supposé optimal d’un spinnaker est à la limite du faseyement, en laissant le guindant se replier légèrement. Cependant ce réglage n’a jamais été scientifiquement étudié auparavant. Nous avons montré qu’il s’agit d’une forte interaction fluide-structure tridimensionnelle où une importante dépression apparaît au bord d’attaque, qui augmente temporairement les efforts, ce qui n’est pas observé avec un réglage plus bordé.A full-scale experimental study on an instrumented sailing yacht is conducted to better assess the aero-elastic behaviour of the sails and rigging in downwind navigations. The downwind sail shape is a non-developable surface with high curvature leading to massive flow separation. In addition, spinnakers are thin and flexible sails leading to a strongly coupled Fluid-Structure Interaction. Due to the non-respect of some rules of similitude, the unsteady behaviour of downwind sails cannot be easily investigated with wind tunnel tests that would need comparison with full-scale experiments. Moreover unsteady numerical simulations modelling the aero-elastic behaviour of the sails and rigging require validations. An inboard instrumentation system has been developed on a 8 meter J/80 sailboat to simultaneously and dynamically measure the flying shape of the spinnaker, the aerodynamic loads transmitted to the rigging, the pressure distribution on the sail as well as the boat and wind data. The shape of the spinnaker while sailing is acquired by a photogrammetric system developed during this PhD. The accuracy of this new system, better than 1.5%, is used to measure the global shape and the main dynamic deformations, such as the flapping of the luff. The aerodynamic load produced by the spinnaker is assessed by the measurements of the load magnitudes and directions on the three corners of the sail (head, tack and clew), and also by the pressure distribution on the spinnaker. The global behaviour of the spinnaker is analysed according to the apparent wind angle. A new representation using Bézier triangular surfaces defines the spinnaker 3D shape. A few control points enable to represent the sail and can easily characterise the type of sail. A typical unsteady behaviour of the spinnaker is also analysed. Letting the luff of the sail flap is known by sailors as the optimal trim but has never been scientifically studied before. It is found that it is a complex three dimensional fluid-structure interaction problem where a high suction near the leading edge occurs, producing a temporary increase of the force coefficient that would not be possible otherwise

Etudes expérimentales de l'Interaction fluide-structure sur les voiles de bateaux au portant

A full-scale experimental study on an instrumented sailing yacht is conducted to better assess the aero-elastic behaviour of the sails and rigging in downwind navigations. The downwind sail shape is a non-developable surface with high curvature leading to massive flow separation. In addition, spinnakers are thin and flexible sails leading to a strongly coupled Fluid-Structure Interaction. Due to the non-respect of some rules of similitude, the unsteady behaviour of downwind sails cannot be easily investigated with wind tunnel tests that would need comparison with full-scale experiments. Moreover unsteady numerical simulations modelling the aero-elastic behaviour of the sails and rigging require validations. An inboard instrumentation system has been developed on a 8 meter J/80 sailboat to simultaneously and dynamically measure the flying shape of the spinnaker, the aerodynamic loads transmitted to the rigging, the pressure distribution on the sail as well as the boat and wind data. The shape of the spinnaker while sailing is acquired by a photogrammetric system developed during this PhD. The accuracy of this new system, better than 1.5%, is used to measure the global shape and the main dynamic deformations, such as the flapping of the luff. The aerodynamic load produced by the spinnaker is assessed by the measurements of the load magnitudes and directions on the three corners of the sail (head, tack and clew), and also by the pressure distribution on the spinnaker. The global behaviour of the spinnaker is analysed according to the apparent wind angle. A new representation using Bézier triangular surfaces defines the spinnaker 3D shape. A few control points enable to represent the sail and can easily characterise the type of sail. A typical unsteady behaviour of the spinnaker is also analysed. Letting the luff of the sail flap is known by sailors as the optimal trim but has never been scientifically studied before. It is found that it is a complex three dimensional fluid-structure interaction problem where a high suction near the leading edge occurs, producing a temporary increase of the force coefficient that would not be possible otherwise.Cette thèse présente une étude expérimentale sur un voilier instrumenté, menée pour décrire le comportement aéro-élastique des voiles et du gréement pour des navigations au portant. Les formes des voiles utilisées sont des surfaces non développables avec de fortes courbures provoquant une séparation massive de l’écoulement. De plus, les spinnakers sont des voiles fines et souples rendant l’interaction fluide-structure fortement couplée. A cause du non-respect de certaines règles de similitude, le comportement dynamique d’un spinnaker se prête mal à l’étude en soufflerie et nécessite une comparaison avec des mesures in-situ. Les simulations numériques instationnaires modélisant le comportement aéro-élastique des voiles et du gréement doivent être qualifiées et demandent également des validations. C’est pourquoi un système d’instrumentation embarquée est mis en place sur un J/80, un voilier de huit mètres de long. Il s’agit de mesurer dynamiquement la forme en navigation du spinnaker, les efforts dans les gréements dormant et courant, la répartition de pression sur la voile ainsi que le vent et les attitudes du bateau. La forme du spinnaker en navigation est obtenue grâce à un système de mesure photogrammétrique développé pendant la thèse. La précision de ce système, meilleure que 1,5%, permet de mesurer la forme générale de la voile ainsi que les déformations importantes telles que celles liées au faseyement du guindant. L’effort aérodynamique produit par le spinnaker est obtenu grâce à la mesure de l’intensité des efforts et de leurs directions aux trois extrémités (drisse, amure, écoute) ainsi que par la mesure des pressions sur la voile. Le comportement général du spinnaker est analysé en fonction de l’angle du vent apparent. Une nouvelle représentation utilisant les surfaces de Bézier triangulaires est développée pour décrire la forme tridimensionnelle du spinnaker. Quelques points de contrôles suffisent pour représenter la voile et caractériser le type de voile. Un comportement dynamique propre au spinnaker est également étudié. Le réglage supposé optimal d’un spinnaker est à la limite du faseyement, en laissant le guindant se replier légèrement. Cependant ce réglage n’a jamais été scientifiquement étudié auparavant. Nous avons montré qu’il s’agit d’une forte interaction fluide-structure tridimensionnelle où une importante dépression apparaît au bord d’attaque, qui augmente temporairement les efforts, ce qui n’est pas observé avec un réglage plus bordé

Experimental studies of fluid-structure interaction on downwind sails

Cette thèse présente une étude expérimentale sur un voilier instrumenté, menée pour décrire le comportement aéro-élastique des voiles et du gréement pour des navigations au portant. Les formes des voiles utilisées sont des surfaces non développables avec de fortes courbures provoquant une séparation massive de l’écoulement. De plus, les spinnakers sont des voiles fines et souples rendant l’interaction fluide-structure fortement couplée. A cause du non-respect de certaines règles de similitude, le comportement dynamique d’un spinnaker se prête mal à l’étude en soufflerie et nécessite une comparaison avec des mesures in-situ. Les simulations numériques instationnaires modélisant le comportement aéro-élastique des voiles et du gréement doivent être qualifiées et demandent également des validations. C’est pourquoi un système d’instrumentation embarquée est mis en place sur un J/80, un voilier de huit mètres de long. Il s’agit de mesurer dynamiquement la forme en navigation du spinnaker, les efforts dans les gréements dormant et courant, la répartition de pression sur la voile ainsi que le vent et les attitudes du bateau. La forme du spinnaker en navigation est obtenue grâce à un système de mesure photogrammétrique développé pendant la thèse. La précision de ce système, meilleure que 1,5%, permet de mesurer la forme générale de la voile ainsi que les déformations importantes telles que celles liées au faseyement du guindant. L’effort aérodynamique produit par le spinnaker est obtenu grâce à la mesure de l’intensité des efforts et de leurs directions aux trois extrémités (drisse, amure, écoute) ainsi que par la mesure des pressions sur la voile. Le comportement général du spinnaker est analysé en fonction de l’angle du vent apparent. Une nouvelle représentation utilisant les surfaces de Bézier triangulaires est développée pour décrire la forme tridimensionnelle du spinnaker. Quelques points de contrôles suffisent pour représenter la voile et caractériser le type de voile. Un comportement dynamique propre au spinnaker est également étudié. Le réglage supposé optimal d’un spinnaker est à la limite du faseyement, en laissant le guindant se replier légèrement. Cependant ce réglage n’a jamais été scientifiquement étudié auparavant. Nous avons montré qu’il s’agit d’une forte interaction fluide-structure tridimensionnelle où une importante dépression apparaît au bord d’attaque, qui augmente temporairement les efforts, ce qui n’est pas observé avec un réglage plus bordé.A full-scale experimental study on an instrumented sailing yacht is conducted to better assess the aero-elastic behaviour of the sails and rigging in downwind navigations. The downwind sail shape is a non-developable surface with high curvature leading to massive flow separation. In addition, spinnakers are thin and flexible sails leading to a strongly coupled Fluid-Structure Interaction. Due to the non-respect of some rules of similitude, the unsteady behaviour of downwind sails cannot be easily investigated with wind tunnel tests that would need comparison with full-scale experiments. Moreover unsteady numerical simulations modelling the aero-elastic behaviour of the sails and rigging require validations. An inboard instrumentation system has been developed on a 8 meter J/80 sailboat to simultaneously and dynamically measure the flying shape of the spinnaker, the aerodynamic loads transmitted to the rigging, the pressure distribution on the sail as well as the boat and wind data. The shape of the spinnaker while sailing is acquired by a photogrammetric system developed during this PhD. The accuracy of this new system, better than 1.5%, is used to measure the global shape and the main dynamic deformations, such as the flapping of the luff. The aerodynamic load produced by the spinnaker is assessed by the measurements of the load magnitudes and directions on the three corners of the sail (head, tack and clew), and also by the pressure distribution on the spinnaker. The global behaviour of the spinnaker is analysed according to the apparent wind angle. A new representation using Bézier triangular surfaces defines the spinnaker 3D shape. A few control points enable to represent the sail and can easily characterise the type of sail. A typical unsteady behaviour of the spinnaker is also analysed. Letting the luff of the sail flap is known by sailors as the optimal trim but has never been scientifically studied before. It is found that it is a complex three dimensional fluid-structure interaction problem where a high suction near the leading edge occurs, producing a temporary increase of the force coefficient that would not be possible otherwise

Experimental analysis of a strong fluid–structure interaction on a soft membrane — Application to the flapping of a yacht downwind sail

In the present study we investigate the flapping instability of a light, soft, highly cambered membrane subject to wind loading. An original in-situ experiment is developed where time-resolved pressures and forces are measured on a full-scale yacht downwind sail called a spinnaker. Particular features of this aero-elastic problem are that the membrane is weakly constrained – held only at three corners –, has a free leading edge, and has no proper shape in the absence of wind loading. In usual operating conditions, the soft structure is subject to a flapping instability giving rise to almost periodic folding and unfolding of the fore part of the sail, associated to strong variations of pressures and forces. This dynamic behavior is analyzed in detail and the space–time evolution of pressures on the membrane is linked to the flapping phenomenon. A peak in forces is observed when the membrane recovers its full shape. Thanks to the Bi-Orthogonal Decomposition (BOD) applied to the pressure fields, the dynamic behavior is reasonably well represented by the two first modes where mode 1 mostly carries the global aerodynamic force behavior and mode 2 mostly represents the effects of the membrane flapping. A physical mechanism of the flapping process is proposed based on the discussion of aerodynamic pressures and strains in the membrane.FP7 PEOPLE - IRSE

Experimental analysis of a strong fluid–structure interaction on a soft membrane — Application to the flapping of a yacht downwind sail

In the present study we investigate the flapping instability of a light, soft, highly cambered membrane subject to wind loading. An original in-situ experiment is developed where time-resolved pressures and forces are measured on a full-scale yacht downwind sail called a spinnaker. Particular features of this aero-elastic problem are that the membrane is weakly constrained – held only at three corners –, has a free leading edge, and has no proper shape in the absence of wind loading. In usual operating conditions, the soft structure is subject to a flapping instability giving rise to almost periodic folding and unfolding of the fore part of the sail, associated to strong variations of pressures and forces. This dynamic behavior is analyzed in detail and the space–time evolution of pressures on the membrane is linked to the flapping phenomenon. A peak in forces is observed when the membrane recovers its full shape. Thanks to the Bi-Orthogonal Decomposition (BOD) applied to the pressure fields, the dynamic behavior is reasonably well represented by the two first modes where mode 1 mostly carries the global aerodynamic force behavior and mode 2 mostly represents the effects of the membrane flapping. A physical mechanism of the flapping process is proposed based on the discussion of aerodynamic pressures and strains in the membrane