Traction Characteristics of a 30 by 11.5-14.5, Type 8, Aircraft Tire on Dry, Wet and Flooded Surfaces

A limited test program was conducted to extend and supplement the braking and cornering data on a 30 x 11.5-14.5, type VIII, aircraft tire to refine the tire/runway friction model for use in the development of an aircraft ground performance simulation. Tire traction data were obtained on dry, wet and flooded runway surfaces at ground speeds ranging from 5 to 100 knots and at yaw angles extending up to 12 deg. These friction coefficients are presented as a function of slip characteristics, namely, the maximum and skidding drag coefficients and the maximum cornering coefficients are presented as a function of both ground speed and yaw angle to extend existing data on that tire size. Tire braking and cornering capabilities were shown to be affected by vehicle ground speed, wheel yaw attitude and the extent of surface wetness

Friction characteristics of 20 x 4.4, type 7, aircraft tires constructed with different tread rubber compounds

A test program was conducted at the Langley aircraft landing loads and traction facility to evaluate the friction characteristics of 20 x 4.4, type, aircraft tires constructed with experimental cut-resistant, tread rubber compounds. These compounds consisted of different blends of natural rubber (NR) and an alfin catalyzed styrene-butadiene copolymer rubber (SBR). One tire having a blend of 30 SBR and 70 NR and another having a blend of 60 SBR and 40 NR in the tread were tested together with a standard production tire with no SBR content in the tread rubber. The results of this investigation indicated that the test tires constructed with the special cut-resistant tread rubber compositions did not suffer any significant degradation in tire friction capability when compared with the standard tire. In general, tire friction capability decreased with increasing speed and surface wetness condition. As yaw angle increased, tire braking capability decreased while tire cornering capability increased. Tread-wear data based on number of brake cycles, however, suggested that the tires with alfin SBR blends experienced significantly greater wear than the standard production tire

Experimental investigation of the cornering characteristics of 18 by 5.5, type 7, aircraft tires with different tread patterns

The characteristics, which include the cornering-force and drag-force friction coefficients and self-alining torque, were obtained on dry, damp, and flooded runway surfaces over a range of yaw angles from 0 deg to 12 deg and at ground speeds from approximately 5 to 90 knots. The results indicate that a tread pattern with pinholes in the ribs reduces the tire cornering capability at high yaw angles on a damp surface but improves cornering on a dry surface. A tread pattern which has transverse grooves across the entire width of the tread improves the tire cornering performance slightly at high speeds on the flooded runway surface. The cornering capability of all the tires is degraded at high ground speeds by thin film lubrication and/or tire hydroplaning effects. Alterations to the conventional tread pattern provide only marginal improvements in the tire cornering capability which suggests that runway surface treatments may be a more effective way of improving aircraft ground performance during wet operations

Studies of some unconventional systems for solving various landing problems

Solutions to various landing problems were obtained through unconventional systems. The first, of these is the air cushion landing system, where efforts were concentrated on development of adequate braking and steering systems and an improved understanding of scaling laws and behavior. The second was concentrated on use of a wire brush skid as a drag producing device, which was shown to have good friction coefficients and reasonable wear rates at ground bearing pressures up to 689 kPa and forward speeds up to 80 km/hr. The third showed great promise in an active control landing gear where significant load reductions were possible during landing impact and subsequent rollout

Accelerometer-controlled automatic braking system

Braking system, which employs angular accelerometer to control wheel braking and results in low level of tire slip, has been developed and tested. Tests indicate that system is feasible for operations on surfaces of different slipperinesses. System restricts tire slip and is capable of adapting to rapidly-changing surface conditions

Molecular dynamics study of the thermopower of Ag, Au, and Pt nanocontacts

Using molecular dynamics simulations of many junction stretching processes we analyze the thermopower of silver (Ag), gold (Au), and platinum (Pt) atomic contacts. In all cases we observe that the thermopower vanishes on average within the standard deviation and that its fluctuations increase for decreasing minimum cross-section of the junctions. However, we find a suppression of the fluctuations of the thermopower for the s-valent metals Ag and Au, when the conductance originates from a single, perfectly transmitting channel. Essential features of the experimental results for Au, Ag, and copper (Cu) of Ludoph and van Ruitenbeek [Phys. Rev. B 59, 12290 (1999)], as yet unaddressed by atomistic studies, can hence be explained by considering the atomic and electronic structure at the disordered narrowest constriction of the contacts. For the multivalent metal Pt our calculations predict the fluctuations of the thermopower to be larger by one order of magnitude as compared to Ag and Au, and suppressions of the fluctuations as a function of the conductance are absent.Comment: 13 pages, 10 figure

Experimental investigation of an accelerometer controlled automatic braking system

An investigation was made to determine the feasibility of an automatic braking system for arresting the motion of an airplane by sensing and controlling braked wheel decelerations. The system was tested on a rotating drum dynamometer by using an automotive tire, wheel, and disk-brake assembly under conditions which included two tire loadings, wet and dry surfaces, and a range of ground speeds up to 70 knots. The controlling parameters were the rates at which brake pressure was applied and released and the Command Deceleration Level which governed the wheel deceleration by controlling the brake operation. Limited tests were also made with the automatic braking system installed on a ground vehicle in an effort to provide a more realistic proof of its feasibility. The results of this investigation indicate that a braking system which utilizes wheel decelerations as the control variable to restrict tire slip is feasible and capable of adapting to rapidly changing surface conditions

Dynamics of aircraft antiskid braking systems

A computer study was performed to assess the accuracy of three brake pressure-torque mathematical models. The investigation utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC-9 series 10 airplane. The investigation indicates that the performance of aircraft antiskid braking systems is strongly influenced by tire characteristics, dynamic response of the antiskid control valve, and pressure-torque response of the brake. The computer study employed an average torque error criterion to assess the accuracy of the models. The results indicate that a variable nonlinear spring with hysteresis memory function models the pressure-torque response of the brake more accurately than currently used models

Experimental investigation of active loads control for aircraft landing gear

Aircraft dynamic loads and vibrations resulting from landing impact and from runway and taxiway unevenness are recognized as significant in causing fatigue damage, dynamic stress on the airframe, crew and passenger discomfort, and reduction of the pilot's ability to control the aircraft during ground operations. One potential method for improving operational characteistics of aircraft on the ground is the application of active control technology to the landing gears to reduce ground loads applied to the airframe. An experimental investigation was conducted which simulated the landing dynamics of a light airplane to determine the feasibility and potential of a series hydraulic active control main landing gear. The experiments involved a passive gear and an active control gear. Results of this investigation show that a series hydraulically controlled gear is feasible and that such a gear is very effective in reducing the loads transmitted by the gear to the airframe during ground operations

Physics development of web-based tools for use in hardware clusters doing lattice physics

Jefferson Lab and MIT are developing a set of web-based tools within the Lattice Hadron Physics Collaboration to allow lattice QCD theorists to treat the computational facilities located at the two sites as a single meta-facility. The prototype Lattice Portal provides researchers the ability to submit jobs to the cluster, browse data caches, and transfer files between cache and off-line storage. The user can view the configuration of the PBS servers and to monitor both the status of all batch queues as well as the jobs in each queue. Work is starting on expanding the present system to include job submissions at the meta-facility level (shared queue), as well as multi-site file transfers and enhanced policy-based data management capabilities