Evaluation of Selected Chemical Processes for Production of Low-cost Silicon, Phase 3

Refinements of the design of the 50 MT/year Experimental Process System Development Unit were made and competitive bids were received from mechanical, electrical, and structural contractors. Bids on most of the equipment were received and cataloged. Emergency procedures were defined to counter a variety of contingencies disclosed in operations and safety reviews. Experimental work with an electrolytic cell for zinc chloride disclosed no significant increase in power efficiency by steps taken to increase electrolyte circulation. On the basis of materials compatibility and permeability tests, 310 stainless steel was chosen for the shell of the fluidized-bed reactor and SiC-coated graphite for the liner

Evaluation of selected chemical processes for production of low-cost silicon, phases 1 and 2

A miniplant, consisting of a 5 cm-diameter fluidized-bed reactor and associated equipment was used to study the deposition parameters, temperature, reactant composition, seed particle size, bed depth, reactant throughput, and methods of reactant introduction. It was confirmed that the permissible range of fluidized-bed temperature was limited at the lower end by zinc condensation (918 C) and at higher temperatures by rapidly decreasing conversion efficiency. Use of a graded bed temperature was shown to increase the conversion efficiency over that obtained in an isothermal bed. Other aspects of the process such as the condensation and fused-salt electrolysis of the ZnCl2 by-product for recycle of zinc and chlorine were studied to provide information required for design of a 50 MT/year experimental facility. In view of the favorable technical and economic indications obtained, it was recommended that construction and operation of the 50 MT/year experimental facility be implemented

Evaluation of Selected Chemical Processes for Production of Low-cost Silicon, Phase 3

The construction of the 50 MT Si/year experimental process system development unit was deferred until FY 1980, and the fluidized bed, zinc vaporizer, by-product condenser, and electrolytic cell were combined with auxiliary units, capable of supporting 8-hour batchwise operation, to form the process development unit (PDU), which is scheduled to be in operation by October 1, 1979. The design of the PDU and objectives of its operation are discussed. Experimental program support activities described relate to: (1) a wetted-wall condensor; (2) fluidized-bed modeling; (3) zinc chloride electrolysis; and (4) zinc vaporizer

Evaluation of selected chemical processes for production of low-cost silicon, phase 3

A Process Development Unit (PDU), which consisted of the four major units of the process, was designed, installed, and experimentally operated. The PDU was sized to 50MT/Yr. The deposition took place in a fluidized bed reactor. As a consequences of the experiments, improvements in the design an operation of these units were undertaken and their experimental limitations were partially established. A parallel program of experimental work demonstrated that Zinc can be vaporized for introduction into the fluidized bed reactor, by direct induction-coupled r.f. energy. Residual zinc in the product can be removed by heat treatment below the melting point of silicon. Current efficiencies of 94 percent and above, and power efficiencies around 40 percent are achievable in the laboratory-scale electrolysis of ZnCl2

Evaluation of selected chemical processes for production of low-cost silicon

Plant construction costs and manufacturing costs were estimated for the production of solar-grade silicon by the reduction of silicon tetrachloride in a fluidized bed of seed particles, and several modifications of the iodide process using either thermal decomposition on heated filaments (rods) or hydrogen reduction in a fluidized bed of seed particles. Energy consumption data for the zinc reduction process and each of the iodide process options are given and all appear to be acceptable from the standpoint of energy pay back. Information is presented on the experimental zinc reduction of SiCl4 and electrolytic recovery of zinc from ZnCl2. All of the experimental work performed thus far has supported the initial assumption as to technical feasibility of producing semiconductor silicon by the zinc reduction or iodide processes proposed. The results of a more thorough thermodynamic evaluation of the iodination of silicon oxide/carbon mixtures are presented which explain apparent inconsistencies in an earlier cursory examination of the system

Evaluation of selected chemical processes for production of low-cost silicon, phase 2

Potential designs for an integrated fluidized-bed reactor/zinc vaporizer/SiCl4 preheater unit are being considered and heat-transfer calculations have been initiated on versions of the zinc vaporizer section. Estimates of the cost of the silicon prepared in the experimental facility have been made for projected capacities of 25, 50, 75, and 100 metric ton of silicon. A 35 percent saving is obtained in going from 25 metric ton/year to the 50 metric ton/year level. This analysis, coupled with the recognition that use of two reactors in the 50 metric ton/year version allows for continued operation (at reduced capacity) with one reactor shut down, has resulted in a recommendation for adoption of an experimental facility capacity of 50 metric ton/year or greater. At this stage, the change to a larger size facility would not increase the design costs appreciably. In the experimental support program, the effects of seed bed particle size and depth were studied, and operation of the miniplant with a new zinc vaporizer was initiated, revealing the need for modification of the latter

Wren’s Walk-Off Bests No. 23 Clemson to Even the Series

Wren’s Walk-Off Bests No. 23 Clemson to Even the Series Junior right fielder hits a bases loaded single with two outs in the nint

Prediction of corporate financial distress : an application of the composite rule induction system

The economic consequence of corporate failure is enormous, especially for the stakeholders of public-held companies. Prior to a corporate failure, the firm’s financial status is frequently in distress. Consequently, finding a method to identify corporate financial distress as early as possible is clearly a matter of considerable interest to investors, creditors, auditors and other stakeholders. This paper uses a composite rule induction system (CRIS; Liang 1992) to derive rules for predicting corporate financial distress in Taiwan. In addition, this paper compares the prediction performance of cris, neural computing and the logit model. The empirical results indicate that both CRIS and neural computing outperform the logit model in predicting financial distress. Although both CRIS and neural computing perform rather well, CRIS has the advantage that the derived rules are easier to understand and interpret.La consecuencia económica de un fracaso corporativo es enorme, especialmente para los actores clave de las compañías públicas. En las fases previas a un fracaso corporativo, es común que el estatus financiero de la firma se encuentre normalmente en apuros. Consecuentemente, encontrar un método para identificar peligros financieros en una corporación tan pronto como sea posible es claramente un asunto con gran interés para los inversores, acreedores, auditores y otros actores clave. Este artículo usa un sistema de reglas inductivas compuestas (CRIS; Liang 1992) para elaborar reglas y patrones que ayuden a predecir problemas económicos en Taiwan. Además, este artículo compara el rendimiento y predicciones de CRIS, la informática neuronal y el modelo logístico. Los resultados empíricos indican que tanto CRIS como la informática neuronal funcionan generalmente bien a la hora de predecir los problemas financieros. Aunque ambos funcionan correctamente, CRIS tiene la ventaja de que sus reglas son más sencillas de entender e interpretar

LSA silicon material task closed-cycle process development

The initial effort on feasibility of the closed cycle process was begun with the design of the two major items of untested equipment, the silicon tetrachloride by product converter and the rotary drum reactor for deposition of silicon from trichlorosilane. The design criteria of the initial laboratory equipment included consideration of the reaction chemistry, thermodynamics, and other technical factors. Design and construction of the laboratory equipment was completed. Preliminary silicon tetrachloride conversion experiments confirmed the expected high yield of trichlorosilane, up to 98 percent of theoretical conversion. A preliminary solar-grade polysilicon cost estimate, including capital costs considered extremely conservative, of $6.91/kg supports the potential of this approach to achieve the cost goal. The closed cycle process appears to have a very likely potential to achieve LSA goals